ADJ Focus Spot Three Z User Instructions

specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their respective companies. ADJ Products, LLC and all affiliated companies hereby dis- claim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, unsufficient and negligent as- sembly, installation, rigging, and operation of this product. Europe Energy Saving Notice Energy Saving Matters (EuP 2009/125/EC) Saving electric energy is a key to help protecting the enviroment. Please turn off all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you! Focus Spot Three Z

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 2 • DMX-512 Protocol Compatible (2 DMX Channel Modes: 18 Chan- nels & 21 Channels) • 3 Operating Modes - Sound Active, Show Mode, & DMX Control • 5 Dimmer Curves (Standard, Stage, TV, Architectural, & Theatre) • Internal Microphone • Digital Display for Address and Function Setting • 4 Preprogrammed Shows • UC IR and Airstream IR Compatiable (Not Included) Focus Spot Three Z Features Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact ADJ Products, LLC. During operation the housing may become extremely hot. Avoid touching the unit with bare hands while in use. ADJ Products, LLC will not accept any liability for any resulting dam- ages caused by the non-observance of this manual or any unauthor- ized modification to this unit. Focus Spot Three Z Handling Precautions Focus Spot Three Z Warranty Registration The Focus Spot Three Z carries a 2 year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase and warranty. You may also register your product online at www. adj- products.com. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty you must provide a copy of your proof of purchase invoice. Please contact ADJ Products, LLC customer support for a R.A. number. To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference. Focus Spot Three Z General Instructions Focus Spot Three Z General Information Unpacking: Thank you for purchasing the Focus Spot Three Z by ADJ Products, LLC. Every Focus Spot Three Z has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all equipment necessary to oper- ate the unit has arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without contacting customer support first. Introduction: The Focus Spot Three Z is a DMX intelligent, moving head, mini LED was. The Focus Spot Three Z can operate as a stand alone fixture or in a Master/Slave set up. The Focus Spot Three Z has three operating modes; a sound active, show mode, DMX controlled. This fixture is suitable for theaters, studios, retail stores, and other similar locations. For best results use fog or special effects smoke to enhance the beams projections. Customer Support: ADJ Products, LLC provides a toll free cus- tomer support line, to provide help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacific Standard Time. Voice: (800) 322-6337 Fax: (323) 582-2941 E-mail: [email protected] Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture. Warning! This may cause severe eye damage. Avoid looking directly into the light source at all times!

Manual Completely Before You Attempt To Install Or Operate This Unit! • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture • Do not spill water or other liquids into or on to your unit. • Be sure that the local power outlet match that of the required volt- age for your unit. • Do not attempt to operate this unit if the power cord has been frayed or broken. • Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. • Disconnect from main power before making any type of connection. • Do not remove the cover under any conditions. There are no user serviceable parts inside. • Never operate this unit when it’s cover is removed. • Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall. • Do not attempt to operate this unit, if it becomes damaged. • This unit is intended for indoor use only, use of this product out- doors voids all warranties. • Always mount this unit in safe and stable matter. • Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep- tacles, and the point where they exit from the appliance. • Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 36 for cleaning details. • Heat -This fixture should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. • The fixture should be serviced by qualified service personnel when: A. Objects have fallen, or liquid has been spilled into the appliance. B. The appliance has been exposed to rain or water. C. The appliance does not appear to operate normally or exhibits a marked change in performance. Focus Spot Three Z Safety Precautions ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 5 ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 4 The Focus Spot Three Z is fully operational in three different mount- ing positions, hanging upside-down from a ceiling, mounted side- ways on trussing, or set on a flat level surface. Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.). Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails (see next page). When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without any deformation. When installing the unit must be secured with a secondary safety attach- ment, e.g. and appropriate safety cable. Never stand directly below the unit when mounting, removing, or servicing the unit. Overhead mounting requires extensive experience, including calculat- ing working load limits, installation material being used, and perodic safety inspection of all installation material and unit. If you lack these qualifications, do not attempt the installation yourself. The installaiton should be checked by a skilled person once a year. Focus Spot Three Z Mounting

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 7 Screw one clamp via a M12 screw and nut to the included bracket. Attach the bracket using the omega locks to the bottom of the Focus Spot Three Z. Attach and pull the safety- cable through one of the safety holes located on the bottom base and over the trussing system or a safe fixation spot. Insert the end in the carabine and tighten the safety screw. NOTICE: The suitable enviromental temperature for this light- ing fixture is between -25˚ C to 45˚ C. Do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above. This will allow the fixture to run at its best and help prolong the fixture life. Focus Spot Three Z Mounting Focus Spot Three Z CAD Drawing 489mm/19.25” 284mm/11.1’ 183mm/7.20”

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 8 Power Supply: The ADJ Focus Spot Three Z contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere. DMX-512: DMX is short for Digital Multiplex. This is a universal pro- tocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fix- ture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal). DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. Therefore, the first fixture controlled by the controller could be the last fixture in the chain. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): The Focus Spot Three Z can be controlled via DMX- 512 protocol. The Focus Spot Three Z has 2 DMX channel modes; 18 channel mode & 21 channel mode. The DMX address is set electronically using the controls on the front panel of the unit. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data cable for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use stan- dard 110-120 Ohm shielded cable (This cable may be purchased at almost all professional sound and Focus Spot Three Z DMX Set Up Figure 1 Focus Spot Three Z Base Layout 1. LED: DMX On DMX input present MASTER On Master Mode SLAVE ON Slave Mode SOUND Flashing Sound activation 2. Display: To show the various menus and the selected function; 3. Button: MENU To select the programming  functions   UP To go forward in the selected functions   DOWN To go backward in the selected functions ENTER To confrm the selected functions 4. IR receiver: To receive the IR signal; 5. Fuse (T5Amp):  Protects the unit from over‐voltage or short circuit; 6. Power In/out:  power cable  connectors for power input/output; 7. DMX In/Out:   3‐pin XLR connectors for DMX 512 operation.

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 11 5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX- 512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting stan- dard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion. Conductor 5-Pin XLR Male (In) 3-Pin XLR Female (Out) Pin 1 Pin 5 - Do Not Use Pin 4 - Do Not Use Pin 3 Pin 2 Pin 1 Pin 3 Pin 2 Not Used Not Used Data True (+ signal) Data Compliment (- signal) Ground/Shield 3-Pin XLR to 5-Pin XLR Conversion Focus Spot Three Z DMX Set Up lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split. Focus Spot Three Z DMX Set Up Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not con- nect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior. DMX512 IN 3-PIN XLR SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT DMX512 DMX+,DMX-,COMMON 1 2 3 Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture. 1 2 3 1 2 3 DMX + DMX - COMMON DMX512 OŠT 3-PIN XLR Figure 2 Figure 3 1 Ground 1 Ground XLR Male Socket XLR Pin Configuration 3 Hot 2 Cold 2 Cold 3 Hot XLR Female Socket Pin 3 = Data True (positive) Pin 2 = Data Compliment (negative) Pin 1 = Ground Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con- nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior. DMX512 IN 3-PIN XLR SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT 1 2 3 Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture. 1 2 3 Figure 4

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 13 Focus Spot Three Z 18 Channel Mode Channel Value Function 1 0 - 255 PAN MOVEMENT 0° - 540° 2 0 - 255 TILT MOVEMENT 0° - 270° 3 COLOR 0 - 7 WHITE 8 - 14 RED 15 - 21 ORANGE 22 - 28 YELLOW 29 - 35 GREEN 36 - 42 BLUE 43 - 49 PURPLE 50 - 56 LIGHT BLUE 57 - 63 PINK 64 - 127 COLOR MIXING 128 - 189 COUNTER CLOCKWISE ROTATION FAST - SLOW 190 - 193 STOP 194 - 255 CLOCKWISE ROTATION SLOW - FAST 4 GOBOS (STATIC) 0 - 7 OPEN 8 - 15 GOBO 1 16 - 23 GOBO 2 24 - 31 GOBO 3 32 - 39 GOBO 4 40 - 47 GOBO 5 48 - 55 GOBO 6 56 - 63 GOBO 7 64 - 72 GOBO 1 SHAKE 73 - 81 GOBO 2 SHAKE 82 - 90 GOBO 3 SHAKE 91 - 99 GOBO 4 SHAKE 100 - 108 GOBO 5 SHAKE 109 - 117 GOBO 6 SHAKE 118 - 127 GOBO 7 SHAKE 128 - 189 COUNTER CLOCKWISE ROTATION FAST - SLOW 190 - 193 STOP 194 - 255 CLOCKWISE ROTATION SLOW - FAST Focus Spot Three Z 18 Channel Mode Channel Value Function 5 GOBOS (ROTATING) 0 - 9 OPEN 10 - 18 GOBO 1 19 - 27 GOBO 2 28 - 36 GOBO 3 37 - 45 GOBO 4 46 - 54 GOBO 5 55 - 63 GOBO 6 64 - 73 OPEN 74 - 82 GOBO 1 SHAKE 83 - 91 GOBO 2 SHAKE 92 - 100 GOBO 3 SHAKE 101 - 109 GOBO 4 SHAKE 110 - 118 GOBO 5 SHAKE 119 - 127 GOBO 6 SHAKE 128 - 189 COUNTER CLOCKWISE ROTATION FAST - SLOW 190 - 193 STOP 194 - 255 CLOCKWISE ROTATION SLOW - FAST 6 GOBO WHEEL 2 GOBO ROTATION 0 - 127 INDEXING 128 - 189 CLOCKWISE ROTATION FAST - SLOW 190 - 193 NO ROTATION 194 - 255 COUNTER-CLOCKWISE ROTATION SLOW - FAST 7 PRISM 0 STOP 1 - 126 6 FACET PRISM 127 NO EFFECT 128 - 255 LINEAR PRISM 8 PRISM ROTATION 0 - 3 STOP 4 - 127 COUNTER CLOCKWISE ROTATION FAST - SLOW 128 - 131 STOP 132 - 255 CLOCKWISE ROTATION SLOW - FAST

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 14 Focus Spot Three Z 18 Channel Mode Channel Value Function 9 STROBE/SHUTTER 0 - 7 OFF 8 - 15 OPEN 16 - 131 STROBING SLOW - FAST 132 - 139 OPEN 140 - 181 SLOW OPEN - FAST CLOSE 182 - 189 OPEN 190 - 231 FAST OPEN - SLOW CLOSE 232 - 239 OPEN 240 - 247 RANDOM STROBE SLOW - FAST 248 - 255 OPEN 10 0 - 255 MASTER DIMMER 0% - 100% 11 0 - 255 FOCUS 0% - 100% 12 AUTO FOCUS 0 - 7 NOTHING 8 - 63 5M FOR AUTO FOCUS 64 - 127 10M FOR AUTO FOCUS 128 - 255 15M FOR AUTO FOCUS 13 0 - 255 ZOOM 18° - 12° 14 SHOWS 0 OFF 1 - 21 SHOW 1 22 - 41 SHOW 2 42 - 61 SHOW 3 62 - 81 SHOW 4 82 - 255 RANDOM SHOW WITH SOUND ACTIVITY 15 0 - 255 SHOW SPEED FAST - SLOW 16 DIMMER MODES 0 - 20 STANDARD 21 - 40 STAGE 41 - 60 TV 61 - 80 ARCHITECTURAL 81 - 100 THEATRE 101 - 255 DEFAULT TO UNIT 17 0 - 255 PAN/TILT SPEED FAST - SLOW Focus Spot Three Z 18 Channel Mode Channel Value Function 18 FUNCTION 0 - 69 NOTHING 70 - 79 ENABLE BLACKOUT WITH PAN/TILT 80 - 89 DISABLE BLACKOUT WITH PAN/TILT 90 - 99 ENABLE BLACKOUT W/ COLOR CHANGE 100 - 109 DISABLE BLACKOUT W/ COLOR CHANGE 110 - 119 ENABLE BLACKOUT W/ GOBO CHANGE 120 - 129 DISABLE BLACKOUT W/ GOBO CHANGE 130 - 139 PAN/TILT MOTOR RESET 140 - 149 COLOR WHEEL MOTOR RESET 150 - 159 GOBO WHEEL MOTOR RESET 160 - 169 EFFECTS RESET (PRISM/FOCUS/ZOOM) 170 - 199 NOTHING 200 - 209 RESET ALL 210 - 255 NOTHING Gobo 1 Gobo 7 Gobo 6 Gobo 5 Gobo 4 Gobo 3 Gobo 2 23.80 mm 20.00 mm 20.00 mm 23.80 mm 20.00 mm 23.80 mm 23.80 mm 20.00 mm 20.90 mm 17.00 mm Gobo 1 Gobo 5 Gobo 4 Gobo 3 Gobo 2 23.80 mm 20.00 mm Gobo 6 Gobo Wheel 1 Gobo Wheel 2

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 17 Focus Spot Three Z 21 Channel Mode Channel Value Function 1 0 - 255 PAN MOVEMENT 0° - 540° 2 0 - 255 PAN FINE 0% - 100% 3 0 - 255 TILT MOVEMENT 0° - 270° 4 0 - 255 TILT FINE 0% - 100% 5 COLOR 0 - 7 WHITE 8 - 14 RED 15 - 21 ORANGE 22 - 28 YELLOW 29 - 35 GREEN 36 - 42 BLUE 43 - 49 PURPLE 50 - 56 LIGHT BLUE 57 - 63 PINK 64 - 127 COLOR MIXING 128 - 189 COUNTER CLOCKWISE FAST - SLOW 190 - 193 STOP 194 - 255 CLOCKWISE ROTATION SLOW - FAST 6 GOBOS (STATIC) 0 - 7 OPEN 8 - 15 GOBO 1 16 - 23 GOBO 2 24 - 31 GOBO 3 32 - 39 GOBO 4 40 - 47 GOBO 5 48 - 55 GOBO 6 56 - 63 GOBO 7 64 - 72 GOBO 1 SHAKE 73 - 81 GOBO 2 SHAKE 82 - 90 GOBO 3 SHAKE 91 - 99 GOBO 4 SHAKE 100 - 108 GOBO 5 SHAKE 109 - 117 GOBO 6 SHAKE 118 - 127 GOBO 7 SHAKE 128 - 189 COUNTER CLOCKWISE FAST - SLOW 190 - 193 STOP 194 - 255 CLOCKWISE ROTATION SLOW - FAST Focus Spot Three Z 21 Channel Mode Channel Value Function 7 GOBOS (ROTATING) 0 - 9 OPEN 10 - 18 GOBO 1 19 - 27 GOBO 2 28 - 36 GOBO 3 37 - 45 GOBO 4 46 - 54 GOBO 5 55 - 63 GOBO 6 64 - 73 OPEN 74 - 82 GOBO 1 SHAKE 83 - 91 GOBO 2 SHAKE 92 - 100 GOBO 3 SHAKE 101 - 109 GOBO 4 SHAKE 110 - 118 GOBO 5 SHAKE 119 - 127 GOBO 6 SHAKE 128 - 189 COUNTER CLOCKWISE ROTATION FAST - SLOW 190 - 193 STOP 194 - 255 CLOCKWISE ROTATION SLOW - FAST 8 GOBO WHEEL 2 GOBO ROTATION 0 - 127 INDEXING 128 - 189 CLOCKWISE ROTATION FAST - SLOW 190 - 193 NO ROTATION 194 - 255 COUNTER-CLOCKWISE ROTATION SLOW - FAST 9 PRISM 0 STOP 1 - 126 6 FACET PRISM 127 NO EFFECT 128 - 255 LINEAR PRISM 10 PRISM ROTATION 0 - 3 STOP 4 - 127 COUNTER CLOCKWISE ROTATION FAST - SLOW 128 - 131 STOP 132 - 255 CLOCKWISE ROTATION SLOW - FAST

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 19 Focus Spot Three Z 21 Channel Mode Channel Value Function 11 STROBE/SHUTTER 0 - 7 OFF 8 - 15 OPEN 16 - 131 STROBING SLOW - FAST 132 - 139 OPEN 140 - 181 SLOW OPEN - FAST CLOSE 182 - 189 OPEN 190 - 231 FAST OPEN - SLOW CLOSE 232 - 239 OPEN 240 - 247 RANDOM STROBE SLOW - FAST 248 - 255 OPEN 12 0 - 255 MASTER DIMMER 0% - 100% 13 0 - 255 MASTER DIMMER FINE 0% - 100% 14 0 - 255 FOCUS 0% - 100% 15 AUTO FOCUS 0 - 7 NOTHING 8 - 63 5M FOR AUTO FOCUS 64 - 127 10M FOR AUTO FOCUS 128 - 255 15M FOR AUTO FOCUS 16 0 - 255 ZOOM 18° - 12° 17 SHOWS 0 OFF 1 - 21 SHOW 1 22 - 41 SHOW 2 42 - 61 SHOW 3 62 - 81 SHOW 4 82 - 255 RANDOM SHOW WITH SOUND ACTIVITY 18 0 - 255 SHOW SPEED FAST - SLOW 19 DIMMER MODES 0 - 20 STANDARD 21 - 40 STAGE 41 - 60 TV 61 - 80 ARCHITECTURAL 81 - 100 THEATRE 101 - 255 DEFAULT TO UNIT 20 0 - 255 PAN/TILT SPEED FAST - SLOW Focus Spot Three Z 21 Channel Mode Channel Value Function 21 FUNCTION 0 - 69 NOTHING 70 - 79 ENABLE BLACKOUT WITH PAN/TILT 80 - 89 DISABLE BLACKOUT WITH PAN/TILT 90 - 99 ENABLE BLACKOUT W/ COLOR CHANGE 100 - 109 DISABLE BLACKOUT W/ COLOR CHANGE 110 - 119 ENABLE BLACKOUT W/ GOBO CHANGE 120 - 129 DISABLE BLACKOUT W/ GOBO CHANGE 130 - 139 PAN/TILT MOTOR RESET 140 - 149 COLOR WHEEL MOTOR RESET 150 - 159 GOBO WHEEL MOTOR RESET 160 - 169 EFFECTS RESET (PRISM/FOCUS/ZOOM) 170 - 199 NOTHING 200 - 209 RESET ALL 210 - 255 NOTHING Gobo 1 Gobo 7 Gobo 6 Gobo 5 Gobo 4 Gobo 3 Gobo 2 23.80 mm 20.00 mm 20.00 mm 23.80 mm 20.00 mm 23.80 mm 23.80 mm 20.00 mm 20.90 mm 17.00 mm Gobo 1 Gobo 5 Gobo 4 Gobo 3 Gobo 2 23.80 mm 20.00 mm Gobo 6 Gobo Wheel 1 Gobo Wheel 2

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 21 Focus Spot Three Z System Menu Focus Spot Three Z System Menu System Menu: When making adjustments press ENTER to confirm your setup then press and hold the MENU button for at least 3 seconds. To exit without making any adjust- ments press the MENU button. The display will lock after 30 seconds, press the MENU button for 3 seconds to unlock. DMX Address - Set the DMX Address - 1. Press the MENU button until “DMX Addresss” is displayed, press ENTER. 2. “X” will now be displayed, “X” represents the displayed address. Press the UP or DOWN buttons to find your desired address. 3. Press ENTER to confirm, and then press and hold the MENU button for at least three seconds to assign. Channel Mode - This will let you select your desired DMX Channel mode. 1. Press the MENU button until “Channel Mode” is displayed, press ENTER. 2. “X Chan” will now be displayed, “X” represents the displayed DMX channel mode. Press the UP or DOWN buttons to find your desired Channel mode. 3. Press ENTER to confirm. Slave Mode - This will let you set unit as a master or slave in a master/slave configuration. 1. Press the MENU button until “Slave Mode” is displayed, press ENTER. Either “Master”, “Slave 1” or “Slave 2” will be displayed. 2. Press the UP or DOWN buttons until your desired setting is displayed, then press ENTER to confim.

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 22 Note: In a Master/Slave configuration you can make one fixture the Master and then set the next fixture to “Slave 2”, the fixtures will now have contrast movement to each other. Show Mode - Show modes 1 - 4 (Factory Shows). 1. Press the MENU button until “Show Mode” is displayed, press ENTER. 2. “Show X” will now be displayed, “X” representing a number between 1-4. Press the UP or DOWN buttons to find your desired show and press ENTER to confirm. After pressing ENTER, press and hold the MENU button for at least 3 seconds to activate. Sound State - In this mode the unit will run in sound active mode. 1. Press the MENU button until “Sound State” is displayed, press ENTER. 2. Either “On” or “Off” will now be displayed. Use the UP or DOWN buttons to toggle between “On” and “Off”. 3. Press ENTER to confirm your selection, the press and hold the MENU button to activate. Sound Sense - In this mode you can adjust the sound sensitivity of the sound active mode. 1. Press the MENU button until “Sound Sense” is displayed, press ENTER. 2. Press the UP or DOWN buttons to adjust the sensitivity level. The sensitivity level can be adjusted between 0 (the lowest) and 100 (most sensitive). 3. Press ENTER to set you desired level. DMX Last State - This mode can be used as a precau- tion mode, that in case the DMX signal is lost, the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is applied. 1. Press the MENU button until “DMX State” is displayed, press ENTER. 2. Either “Master/Slave”, “Blackout”, or “Last State” will be dis- played. Choose an operating mode you would like the unit to start up in when power is applied or the DMX signal is lost. • Master/Slave - If the DMX signal is lost or power is applied, the unit will automatically go into Master Slave mode. • Blackout - If the DMX signal is lost or power is applied, the unit will automatically go into stand by mode. • Last State - If the DMX signal is lost the fixture will stay in the last DMX set up. If power is applied and this mode is set, the unit will automatically go into the last DMX set up. 3. Press ENTER to confirm your desired set up. Dimmer Curve - In this mode you can select the dimmer curve. 1. Press the MENU button until “Dimmer Curve” is displayed, press ENTER. 2. The current dimmer curve setting will be displayed. 3. Press the UP or DOWN buttons to find your desired dimmer curve and press ENTER to confirm. See the Dimmer Curve Chart on page 22 for the settings. Focus Spot Three Z System Menu Focus Spot Three Z System Menu

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 25 Pan Invert - Pan Inversion 1. Press the MENU button until “Pan Invert” is displayed, press ENTER. Either “Yes” or “No” will be displayed. 2. To activate the Pan inversion press the UP or DOWN buttons until “Yes” is displayed, press ENTER to confim. To deactivate Pan inversion, select “No” and press Enter. Tilt Invert - Tilt Inversion 1. Press the MENU button until “Tilt Invert” is displayed, press ENTER. Either “Yes” or “No” will be displayed. 2. To activate the Tilt inversion press the UP or DOWN buttons until “Yes” is displayed, press ENTER to confim. To deactivate Tilt inversion, select “No” and press Enter. Back Light - With this function you can make the back- light automatically turn off after one minute. 1. Press the MENU button until “Back Light” is displayed, press ENTER. 2. Either “On” or “Off” will now be displayed. Press the UP or DOWN buttons to select “On” to keep the backlight on at all times, or “Off” to allow the backlight to turn off after 1 minute. Press any button to turn the backlight on again. Manual Test - This function will let you manually test the individual features. 1. Press the MENU button until “Manual Test” is displayed, press ENTER. 2. Use the UP or DOWN buttons to find the functions that you wish to test. 3. Once you find a function you wish to test, press the ENTER button, the displayed value will begin to flash. You can now adjust the values by pressing the UP and DOWN buttons. Once you have finished testing press the ENTER button. 4. To exit the manual test mode, press the MENU button. Auto Test - This function will run a self test program. 1. Press the MENU button until “Auto Test” is displayed, press ENTER. 2. The fixture will now run a self test. Press the MENU button to exit. Function Delay - With this function you can set a delay for the reset functions in DMX mode. 1. Press the MENU button until “Function Delay” is displayed, press ENTER. 2. Either “No Delay” or time between 1s - 3s will be displayed. This number represents the delay setting. Use the UP and DOWN buttons to adjust the blackout delay. Example: If the delay is set to 3 seconds, and you go to reset the pan/tilt motors, it will take 3 seconds for the reset to begin. 3. Press ENTER to confirm. Zoom Mode - With this function you can adjust the zoom. 1. Press the MENU button until “Zoom Mode” is displayed, press ENTER. 2. The current zoom setting will be displayed. 3. Press the UP or DOWN buttons to adjust the zoom between 5M, 10M, or 15M. Press ENTER to confirm your setting. Focus Spot Three Z System Menu Focus Spot Three Z System Menu

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 27 Focus Spot Three Z System Menu Fixture Temp. - With this function you can display the running temperature of the unit. 1. Press the MENU button until “Fixture Temp.” is displayed, press ENTER. 2. The current running temperature of the fixture will now be displayed. Press MENU to exit. Fixture Time - With this function you can display the running time of the unit. 1. Press the MENU button until “Fixture Time” is displayed, press ENTER. 2. The running time of the fixture will now be displayed. Press MENU to exit. Firmware Version - This will display the firmware/soft- ware version 1. Press the MENU button until “Firmware Version” is displayed. Press the ENTER button and the firmware/software vesion will be displayed. 2. Press the MENU button to leave this function. PRO Defaults - This function will restore all factory settings. 1. Press the MENU button until “PRO defaults” is displayed, press ENTER. Either “Yes” or “No” will be displayed. 2. To restore factory settings press the UP or DOWN buttons until “Yes” is displayed, press ENTER to confim. If you do not wish restore the settings, select “No” and press Enter. Reset - Use this function to reset the motors. 1. Press the MENU button until “Reset” is displayed, press ENTER. 2. The fixture will now reset. Focus Spot Three Z System Menu

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 29 Focus Spot Three Z Home Adjustment Menu To enter the Offset Menu, press the MENU button to unlock the display, then press the ENTER button for at least 5 seconds. In this submenu you are able to adjust the home position of the pan, tilt, gobo wheels, color wheel, prisms, focus, and zoom . Pan Offset - Adjustment of the pan home position. 1. Press the ENTER button for at least 5 seconds, then press the UP or DOWN buttons so that “Pan Offset” is displayed, press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. Tilt Offset - Adjustment of the tilt home position. 1. Press the ENTER button for at least 5 seconds, then press the UP or DOWN buttons so that “Tilt Offset” is displayed, press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. Gobo 1 Offset - Setting adjustment for the 1st gobo wheel. 1. Press the ENTER button for at least 5 seconds, then press the UP or DOWN buttons so that “Gobo 1 Offset” is displayed, press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. Gobo 2 Offset - Setting adjustment for the 2nd gobo wheel. 1. Press the ENTER button for at least 5 seconds, then press the UP or DOWN buttons so that “Gobo 2 Offset” is displayed, press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. Color Offset - Setting adjustment for the color wheel. 1. Press the ENTER button for at least 5 seconds, then press the UP or DOWN buttons so that “Color” is displayed, press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. Prism 1 Offset - Setting adjustment for the 1st prism. 1. Press the ENTER button for at least 5 seconds, then press the UP or DOWN buttons so that “Prism 1 Offset” is displayed, press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. Focus Spot Three Z Home Adjustment Menu

Universal DMX Control: This function allows you to use a univer- sal DMX-512 controller to control the chases and patterns, dimmer and strobe. A DMX controller allows you to create unique programs tailored to your individual needs. 1. The Focus Spot Three Z has 2 DMX channel modes; 18 channel mode, and 21 channel mode. See pages 12-19 for detailed description of the DMX values and traits. 2. To control your fixture in DMX mode, follow the set-up procedures on pages 9-11 as well as the set-up specifications that are includ- ed with your DMX controller. 3. Use the controller’s faders to control the various DMX fixture traits. 4. This will allow you to create your own programs. 5. Follow the instructions on page 21 to select your desired DMX channel mode and to set the DMX address. 6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture. 7. For help operating in DMX mode consult the manual included with your DMX controller. Sound Active Mode: This mode allows either single unit or several units linked together, to run to the beat of the music. 1. Press the MENU button until “Sound State” is displayed, and press ENTER. Press the UP or DOWN buttons so that “ON” is dis- played and press ENTER. 2. Press the MENU button until “Sound Sense” is displayed, and press ENTER. Use the UP and DOWN buttons to adjust the sound sensitivity. Press ENTER when you have found your desired sensi- tivity level. Show Mode: This mode allows either a single unit or several units linked together, to run one of four shows that you choose. 1. Press the MENU button until “Show Mode” is displayed, and press ENTER. 2. Press the UP or DOWN buttons to find your desired show, and press ENTER. Focus Spot Three Z Operation ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 31 Focus Spot Three Z Home Adjustment Menu Prism 2 Offset - Setting adjustment for the 2nd prism. 1. Press the ENTER button for at least 5 seconds, then press the UP or DOWN buttons so that “Prism 1 Offset” is displayed, press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. Rprism Offset - Setting adjustment for the rotating prism. 1. Press the ENTER button for at least 3 seconds, then press the UP or DOWN buttons so that “Rprsim Offset” is displayed, press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. Focus Offset - Setting adjustment for the focus. 1. Press the ENTER button for at least 3 seconds, then press the UP or DOWN buttons so that “Focus Offset” is displayed, press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. Zoom Offset - Setting adjustment for the zoom. 1. Press the ENTER button for at least 3 seconds, then press the UP or DOWN buttons so that “Zoom Offset” is displayed, press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit.

various functions (See below). To control the fixture you must aim the remote at the front of the fixture and be no more than 30 feet away. The Airstream IR (sold separately) remote transmitter plugs into the headphone jack of your iOS phone or tablet. To control your IR fixture you must raise the volume to the maximum on your iOS phone or tablet and aim the transmitter at the fixture sensor and be no more than 15 feet away. After you have purchased the Airstream IR trans- mitters, the app is a free download from the app store for your iOS phone or tablet. The app comes with 3 pages of control depending on the fixture you are using. Please see below for IR functions. This unit works with App page 1. STAND BY - Pressing this button will blackout the fixture. FULL ON - Hold this button down to fully light up the unit. When you let the button go, the unit will return to its previous state. FADE/GOBO - Press this button once to access gobo wheel 1, press the button again to access gobo wheel 2. Use the number buttons to find your desired gobo. “DIMMER +” and “DIMMER -” - Use these buttons to adjust the out- put intensity in Color mode. STROBE - This button will activate the strobe effect. Press and hold this button to activate strobing and release the button to stop strob- ing. COLOR - Press this button to enter to access the color wheel. Use the number buttons to select your desired color. Adjust the output intensity using the “DIMMER +” and “DIMMER -” buttons. 1-9 - In color mode and gobo mode, these buttons will allow you to select a desired color or gobo. In show mode buttons 1-4 will let you select your desired show. SOUND ON & OFF - These buttons activate and deactivate the sound active mode. SHOW - This activates the show mode. Use buttons 1-4 to select your desired show. Focus Spot Three Z Remote Operation Focus Spot Three Z Master-Slave Set Up Master-Slave Operation This function will allow you to link up to 16 units together and operate without a controller. The units will be sound activated. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave. 1. Using approved DMX data cables, daisy chain your units togeth- er via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a termina- tor at the last fixture. 2. On the Master unit press the MENU button until “Slave Mode” is displayed, and press ENTER. Use the UP and DOWN buttons to scroll to the “Master” setting and press ENTER. 3. After setting the Master unit to the master setting find and set your desired operating mode. 4. On the slave units press the MENU button until “Slave Mode” is displayed, and press ENTER. Choose either “Slave 1” or “Slave 2” and press ENTER. 5. The slave units will now follow the Master unit. ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 32 ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 33 With this feature you can connect the fixtures to one another using the PowerCon input and output sockets. The quantity that can be connected is 3 fixtures maximum @ 120V and 6 fixtures maximum @ 230V. After you have reached the maximum amount of fixtures you will need to use a new power outlet. They must be the same fixtures. DO NOT mix fixtures. Focus Spot Three Z Power Cord Daisy Chain

ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 35 Focus Spot Three Z Dimmer Curve Chart (Fade Time) (Fade Time) Ramp Effect Standard Stage TV Architectural Theatre Focus Spot Three Z Photometric Chart The gobo’s in the second gobo wheel are the only gobo’s that are interchangable in this unit. Please be very careful when replacing the gobo. Caution! Never open the unit when in use. Always disconnect the main power before attempting to change the gobos. 1. To change a gobo, look inside the unit from the front lens and notice the prisms. Rotate the moving head so that prisms are facing down. The top shell facing you is the shell you need to remove. 2. Uscrew the 4 screws that secure the shell to the unit. Gently lift the shell off of the unit. 3. When you remove the shell you will be able to access the gobo wheel. Turn the wheel with your hand until you come across the gobo you would like to change. 4. Gently and carefully remove the fixture ring. You will notice that small dab of high temperature silicon holds the fixture ring. After the fixture ring is removed, carefully remove the gobo. 5. Change the gobo and replace the fixture ring. 6. Reassemble the unit. Focus Spot Three Z Changing the Gobo

Warranty MANUFACTURER’S LIMITED WARRANTY A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruction manual. D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect. E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published. MANUFACTURER’S LIMITED WARRANTY PERIODS: • Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps) • Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser diodes which have a 6 month limited warranty) • L.E.D. Products = 2-year (730 days) Limited Warranty (excluding motors, PCB boards, and power supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited war- ranty). Only the L.E.D.s carry a 2-year warranty (excluding StarTec Series which a carries a 1 Year Limited Warranty) Note: 2 Year Warranty only applies to purchases within the United States. • ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty (excluding faders and tact switches) Focus Spot Three Z Cleaning Focus Spot Three Z Trouble Shooting Trouble Shooting: Listed below are a few common problems that you may encounter, with solutions. No light output from the unit; 1. Be sure the external fuse has not blown. The fuse is located on the rear panel of the unit. 2. Be sure the fuse holder is completely and properly seated. Unit does not respond to sound; 1. Low frequencies (bass) should cause the unit to react to sound. Tapping on the microphone, quiet or high pitched sounds may not activate the unit. Due to fog residue, smoke, and dust cleaning the internal and exter- nal optical lenses and mirror should be carried out periodically to optimize light output. Cleaning frequency depends on the environ- ment in which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp output. 1. Use normal glass cleaner and a soft cloth to wipe down the out- side casing. 2. Use a brush to wipe down the cooling vents and fan grill. 3. Clean the external optics with glass cleaner and a soft cloth every 20 days. 4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days. 5. Always be sure to dry all parts completely before plugging the unit back in. Focus Spot Three Z Fuse Replacement Locate and remove the unit’s PowerCon cord. Once the cord has been removed the fuse holder is located next to the power socket. Use a philips-head screw driver unscrew the fuse holder. Remove the bad fuse and replace with a new one. ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 36 ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 37

of this unit and this manual are subject to change without any prior written notice. Focus Spot Three Z Specifications Model: Focus Spot Three Z Voltage: 100 - 240V, 50/60Hz LED: 1 x 100W Cold White LED Power Consumption: 230W Dimensions: 7.25”(L) x 11.25”(W) x 19.75”(H) 183mm x 284mm x 489mm Weight: 26 Lbs. / 12 kgs. Beam Angle: 12-18 Degrees Fuse: 5 Amp Power Cord Daisy Chain: 3 Fixtures Max. (120V) 6 Fixtures Max. (230V) Duty Cycle: None DMX: 2 DMX Channel Modes: 18 Channel Mode & 21 Channel Mode Sound Active: Yes Working Position: Any Safe, Secure Position Warranty: 2 Year (730 days) Auto Sensing Voltage: This fixture contains a automatic volt- age switch, which will auto sense the voltage when it is plugged into the power source. ADJ Products, LLC 6122 S. Eastern Ave. Los Angeles, CA 90040 USA Tel: 323-582-2650 / Fax: 323-725-6100 Web: www.adj.com / E-mail: [email protected] A.D.J. Supply Europe B.V. Junostraat 2 6468 EW Kerkrade The Netherlands [email protected] / www.adj.eu Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99 ADJ Products, LLC - www.adj.com - Focus Spot Three Z Instruction Manual Page 38