Clemco Zero Pulsar 3D Manual 

NOTICE TO PURCHASERS AND USERS OF OUR PRODUCTS AND THIS INFORMATIONAL MATERIAL Clemco proudly provides products for the abrasive blast industry and is confident that industry professionals will use their knowledge and expertise for the safe and efficient use of these produc ...

Page 1 © 2020 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 29374 1.0 INTRODUCTION 1.1 Scope of Manual 1.1.1 These instructions cover setup, operation, maintenance, troubleshooting, optional accessories, and replacement parts for the following Pulsar® 3D Suction Blast Cabinet: 1.1.2 The instructio ...

Page 2 © 2020 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 29374 PREVENTIVE MAINTENANCE ................................. 5.0 Daily Inspection and Maintenance Before Blasting ...... 5.1 Check media level in reclaimer ............................ 5.1.1 Inspect reclaimer debris screen and door gas ...

Page 3 © 2020 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 29374 Figure 1 1.5 Theory of Operation 1.5.1 Once the cabinet is correctly set up and turned on, the cabinet is then ready for operation by actuation of the foot pedal. Fully depressing down on the foot pedal causes air to flow through the ...

Page 4 © 2020 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 29374 1.7 Nozzle Options 1.7.1 Ventilation requirements limit standard cabinets to No. 5 (5/16" orifice) nozzle and No. 5 (5/32" orifice) air jet. Unless otherwise specified at the time of order, cabinets are supplied with a tungsten carbi ...

Page 5 © 2020 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 29374 2.2.1 Refer to Figure 2 and apply thread sealant to the male threads of an air fitting that is compatible with the air-supply hose fitting, and install it onto the 1/2" NPT inlet solenoid located on the side of the cabinet. The style ...

Page 6 © 2020 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 29374 2.3 Ground Cabinet 2.3.1 To prevent static electricity buildup, attach an external grounded wire from an earth ground to the grounding bolt on the rear of the cabinet. 2.4 Connect Media Hose to Metering Valve 2.4.1 Refer to Figure 3 ...

Page 7 © 2020 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 29374 3.4 Loading and Unloading Parts NOTE: Parts must be free of oil, water, grease, or other contaminants that will clump media or clog filter cartridge. 3.4.1 Load and unload parts through the top door. 3.4.2 When blasting small parts o ...

Page 8 © 2020 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 29374 3.7 Stop Blasting 3.7.1 To stop blasting, remove foot pressure from the top of the foot pedal. 3.7.2 Keep door closed and exhauster running until the cabinet is clear of all airborne dust. 3.7.3 Unload parts. 3.8 Pulsing (Cleaning) D ...

Page 9 © 2020 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 29374 4.3 Optional Manometer NOTE: These instructions show several methods of taking static pressure readings (negative pressure) on the Pulsar® 3D Reclaimer by using a flexible-tube manometer. Use the method best suited for the applicati ...