Congatec conga-SKIT Quick Start Manual

Text of Congatec conga-SKIT Quick Start Manual

Copyright © 2017 congatec AG

SKIT_q12 1/8 conga-SKIT Starter Kit for congatec SMARC 2.0 Development Quick Start Guide Revision 1.2
Copyright © 2017 congatec AG SKIT_q12 2/8 Preface This quick start guide provides information on the contents of the conga-SKIT kit and how to set it up. Disclaimer The information contained within this quick start guide, including but not limited to any product specification, is subject to change without notice. congatec AG provides no warranty with regard to this guide or any other information contained herein and hereby expressly disclaims any implied
Copyright © 2017 congatec AG SKIT_q12 3/8 Warranty congatec AG makes no representation, warranty or guaranty, express or implied regarding the products except its standard form of limited warranty (“Limited Warranty”) per the terms and conditions of the congatec entity, which the product is delivered from. These terms and conditions can be downloaded from www.congatec.com. congatec AG may in its sole discretion modify its Limited Warranty at any time
Copyright © 2017 congatec AG SKIT_q12 4/8 1 Introduction 1.1 conga-SKIT The conga-SA5 features a quad-core Intel® Atom™ x7-E3950 processor with up to 2.0 GHz, Gen 9 graphics with 18 execution units and 8 GB LPDDR4 RAM. Other features are 433 Mbit/s WLAN 802.11 b/g/n/ac, Bluetooth LE, dual GbE, USB 3.0, 32 GB eMMC 5.0 flash memory and TPM 2.0. The conga-SEVAL evaluation carrier board provides 1x PCIe x4, 1x PCIe x1, 1x mini PCIe, 1x M.2 Key E, 2x USB 3.
Copyright © 2017 congatec AG SKIT_q12 5/8 1.3 Connecting the Hardware Steps: 1. Ensure the hardware is protected from the effects of electrostatic discharge (ESD). 2. Attach the WLAN antenna cable to the MAIN connector of the conga-SA5 module. 3. Attach the conga-SA5 module to the conga-SEVAL carrier board. 4. Install the conga-SA5/i-HSP-B heatspreader or conga-SA5/i-CSP-B passive cooling solution using four screws. 5. Connect the desired adapters, c
Copyright © 2017 congatec AG SKIT_q12 6/8 1.4 Interfaces GND AT_CARRIER 12V..24V PWR_LCD0 eDP0 EPI LVDS/DSI eDP1 PWR_LCD1 SD/MMC CGBC JTAG GPIO [O:3] PM_I2C GP_I2C USB0 (OTG) SPDIF GbE0/1 Trigger GbE1 USB1 + USB2 USB Type -C DP0 / HDMI0 RS232 COM0 RS232 COM1 FAN Battery Support CAN1 CAN0 SPIO SPIO eSPI PM MODULE CMOS Battery M.2 mini PCIe SATA HDD Power Feature Connector SPKR MIC CSI ATX 24 pin X63 GbE0 GND AT_SMARC 3.0V..5.25V SIM Card PCIe PCIe
Copyright © 2017 congatec AG SKIT_q12 7/8 1.5 DIP Switch Settings M11 - DIP Switch (Wireless Disable Signal 1, 2) Switch # Switch ON Switch OFF 1 W_DISABLE1# ON W_DISABLE1# OFF 2 W_DISABLE2# ON W_DISABLE2# OFF M12 - DIP Switch (Audio and Display) Switch # Switch ON Switch OFF 1 HDA I²S 2 eDP LVDS / DSI M18 - DIP Switch (SPI_HOLD#) Switch # Switch ON Switch OFF 2 SPI_HOLD# ON SPI_HOLD# OFF M18 - DIP M17 - DIP Selected Boot Source Switch 1 Switch 2 Switch
Copyright © 2017 congatec AG SKIT_q12 8/8 1.6 Jumper Settings X16 - LAN LEDs Pin Configuration 1-2 Standby powered 2-3 Main powered X22 - LCD0 VDD Pin Configuration 1-2 3.3 V panel power 2-3 5 V panel power X24 - LCD0 BKLT_EN Pin Configuration 1-2 Non-inverted 2-3 Inverted X25 - LCD0 BKLT Pin Configuration 1-2 Backlight power 12 V 2-3 Backlight power 5 V X27 - LCD1 Panel Power Pin Configuration 1-2 3.3 V 2-3 5 V X28 - LCD1 BKLT1 Pin Configuration 1-2 12 V

Congatec Microcontrollers Owners Instructions: