DPCAV AV681TX Quick Start Manual
Read Online
Read the DPCAV AV681TX Quick Start Manual online using the built-in PDF viewer.
Key Pages of Document
Page 1 © Nov-03-2008 AV681TX 5.8GHZ A/V TRANSMITTER KIT Rev-C Hardware INTRODUCTION This 5.8Ghz 100mW A/V transmitter kit provides a custom printed circuit board set and quality electronic components. All you need to add is an antenna of your choice and about three hours of your time. NOTICE: This kit involves precision SMD soldering and it is NOT intended for beginners to assemble. It is suitable for amateur radio hobbyists and RF tec ...
Page 2 © Nov-03-2008 Figure 2, Side ã Figure 3, Side ä ASSEMBLY INSTRUCTIONS 1 GENERAL NOTES 1.1 These instructions are for the Rev-C hardware release. Before starting, be sure to confirm your kit is identified as Rev-C. 1.2 The top and bottom sides of the two PCB’s are labeled with a circled number (e.g., â ã ä å). The instructions will reference the numbered side that is being assembled. 2 SIDE ã ãã ã, COMPONENTS: See Fig ...
Page 3 © Nov-03-2008 Figure 4, Side å Figure 5, Stand-Off Posts 4 SIDE å åå å, COMPONENTS: See Figure 4. 9 4.1 Install R1, R2, and R3 (2.2K resistors). 9 4.2 Install C8 (.1uF cap). 5 SIDE ä ää ä, POST INSTALLATION: See Figure 5. 9 5.1 Carefully cut the standoff post header so that you have one piece that is 2-pins and two pieces that are 1-pin. 9 5.2 Install the 2-pin POWER post at J1. 9 5.3 Install a 1-pin GND post at the hol ...
Page 4 © Nov-03-2008 Figure 6, RF Module Installation Figure 7, SMA-RP Top Side Figure 8, SMA-RP Bottom Side 7 RF MODULE INSTALLATION: See Figure 6. Note: The RF Module and the SMA-RP installation have changed with the Rev-C release. 9 7.1 Place the AWM681TX module on the PCB (Side ä). It will have a gap between it and the PCB. It does NOT sit flush. See Figure 6 for details. 9 7.2 Before soldering the RF module in place, temporarily ...
Page 5 © Nov-03-2008 Figure 9, A/V Cables 9 8.3 If the RF module is expected to be used in an application that has vibration then it is helpful to solder two diagonal corners of the RF module’s top tin lid to the tin metal base. This will help prevent video noise. 9 SIDE å åå å, A/V CABLE INSTALLATION: See Figure 9. 9 9.1 Install your audio/video wires to the AV-IN pads as follows: G = A/V GND R = RIGHT AUDIO L = LEFT AUDIO V = V ...
Page 6 © Nov-03-2008 Figure 10, Foam Pad Figure 11, Heatshrink 10 FINAL ASSEMBLY: JOIN THE TWO PCB’s TOGETHER 9 10.1 Using an approved PCB cleaner, remove the flux from ALL soldered connections. Flush trim all the component leads from sides â and å. 9 10.2 Inspect your work. Now is the time to find errors -- once the boards are joined it will be very inconvenient to do this. 9 10.3 See Figure 10. Cut the double-sided foam pad in ha ...
Page 7 © Nov-03-2008 NOTICE Digital Products Company, or their distributors, have no control over the assembly and use of this A/V RF system. As such, no liability may be assumed, nor will any liability be accepted, for any damages resulting from the use of this product. Under no circumstances will the buyer be entitled to consequential or incidental damages. By act of using it, the buyer accepts all resulting liability. 12 AUDIO CONFI ...
AV-681TX C Title: Size: Date: Revision: Sheet of Letter DPC A/V AUDIO VIDEO www.dpcav.com Copyright: NOV-03-2008 2008 GND 1 N/A 2 SW2 3 AUD-L 7 SW1 4 SW0 5 AUD-R 6 VID 8 GND 11 GND 13 ANT 12 VCC 9 BYPASS 10 U1 AWM681TX 1 2 J1 HDR2P + C2 330uF + C21 47uF 16V + C22 47uF 6V 6.5VDC MIN 8.5VDC MAX IN 1 OUT 3 GND 2 U21 KF50BDT D20 DL4001 + C4 330uF 1 2 DC-IN PWR AIRWAVE AWM681 TX +5 C8 .1uF +5 1 2 3 4 AV HDR4P AU ...
Related Devices for DPCAV AV681TX:
AV681TX-Kit, Rev B Page 1 © Nov-03-2008 AV681TX 5.8GHZ A/V TRANSMITTER KIT Rev-B Hardware INTRODUCTION This 5.8Ghz 100mW A/V transmitter kit provides a custom Professional operation guide for the DPCAV AV681TX Transmitter. It offers guidance for setup and power requirements, maintenance, application scenarios.
ORACLE V1.4 ©2007-2008 DIGITAL PRODUCTS COMPANY PAGE 1 Jan-2008 ORACLE VIDEO DIVERSITY CONTROLLER The Oracle video diversity controller is used to bridge two w Product setup manual for the DPCAV Oracle Controller. It offers guidance on compatibility information, software configuration, installation procedures.
DIVERSITY DEMON FPV PRO RACE EDITION TRI-DIVERSITY VIDEO CONTROLLER Diversity Demon is a video controller that is used to bridge three wireless video receivers Installation and operation manual for the DPCAV DIVERSITY DEMON FPV PRO RACE EDITION Stereo Receiver. This documentation details maintenance procedures, technical guidelines, functional overview.
AV681TX-Kit, Rev C Page 1 © Nov-03-2008 AV681TX 5.8GHZ A/V TRANSMITTER KIT Rev-C Hardware INTRODUCTION This 5.8Ghz 100mW A/V transmitter kit provides a custom User instruction manual for the DPCAV AV681TX Transmitter. This guide explains the features and safety information, connectivity setup, application scenarios, software installation.
AV680RX-Kit, Rev-B Page 1 © Nov-03-2008 AV680RX 5.8GHZ A/V RECEIVER KIT Rev-B Kit INTRODUCTION Thanks to this handy kit, building a high performance 5.8GHz A/V Complete usage guide for the DPCAV AV680RX Receiver. The manual elaborates on features and network configuration, installation steps, specifications, warranty information.
PANDORA (REV-C), www.dpcav.com Page 1 ©2007-2008 Jun-11-2008 Figure 2, Kit Contents PANDORA Pan & Tilt Kit (REV-C) www.dpcav.com The items shown in the photo Product reference manual for the DPCAV PANDORA Control Unit. This reference includes firmware installation, safety precautions, operating modes.
Part Number: LCD-RC801-NBC Part Number: LCD-RC801-SMA BLACK PEARL RC801 7”Screen / 5.8GHz / FPV Diversity RX Instruction Manual Before operating the unit: Ple Official installation manual for the DPCAV BLACK PEARL RC801 Monitor. The manual elaborates on features and performance details, specifications, software configuration, installation guides.
ShutterBug Pro © 2007-2013 Page 1 Sep-15-2013 Figure 3, Shutter Servo SHUTTERBUG PRO Digital Camera Controller ShutterBug Pro is a tiny accessory that helps ta Manual for installation and usage of the DPCAV ShutterBug Pro Controller. It provides information on installation and software configuration, maintenance schedule, usage tips, firmware updates.
Transmitter: Frequently Requested PDF Instructions
24 GHz Non-contact Radar (FMCW) Level Meter for distance, level, volume and mass measurement of liquids OPTIWAVE 7300 C OPTIWAVE 7300 C OPTIWAVE 7300 C OPTIWAVE Device user manual for the KROHNE OPTIWAVE 7300 C Measuring Instruments. This manual provides information on configuration options, system setup, power requirements.
smart Installation / User Manual TRANSMITTER-PLC/TRANSMITTER-PLC-PCBA/ TRANSMITTER-PLC OUTDOOR KIT ALTENERGY POWER SYSTEM INC. www.APsmartGlobal.com © All Righ Setup instructions for the APsmart RSD-S-PLC Switch. The guide provides instructions on system configuration, safety features, operating conditions.
1 SATRON VC Optical Consistency Transmitter BCs220AV Revision 2 15.10.2014 Contents: 1. INSTALLATION 1.1 Mounting location s. 2 1.2 Installing the transmitt Complete usage guide for the Satron Instruments SATRON VC Transmitter. This guide provides information on configuration options, device safety checks, connectivity options, calibration steps.
D-300909 TOWER 10 AM, TOWER 12 AM Installation Instructions 1 TOWER 10 AM, TOWER 12 AM [GRADE 3] English Anti-Masking PIR and Dual technology (PIR/MW) Mirror De User operation guide for the Visonic TOWER 10 AM - Transmitter. This guide includes usage recommendations, user preferences, dimensions and layout, usage examples.