Finn B-70 Manual 

Quality Manual 9281 LeSaint Drive • Fairfield, Ohio 45014 Phone (513) 874-2818 • Fax (513) 874-2914 1-800-229-8707

Safety Summary Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Definition of Mulching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Towing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Loading Bales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pre-Start Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Equipment Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Starting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Crew Members and Their Duties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Blower Discharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4-8 Hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Daily Clean-up Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Weekly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Lubrication and Fluids Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Clutch Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-12 Parts Manual Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-30 Discharge Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15 Shredder Box and Feed Chute (Std) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Shredder Box and Feed Chute (R-H) . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Blower and Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Trailer Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Trailer Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21 Engine Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23 Power Take-Off Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25 Engine Wiring Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27 Control Box Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29 B70 Decals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-31 Tool Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Warranty Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

important part of its operation is SAFETY! Finn Corporation encourages you and your employees to familiarize yourselves with your new equipment and to stress safe operation. The first four pages of this manual are a summary of all the main safety aspects associated with this unit. Be sure to read completely before operation of machine. This symbol is used throughout the operation and maintenance sections of this manual to call attention to safety procedures. - Pay Attention - DANGER: Immediate hazards which WILL result in severe personal injury or death. WARNING: Hazards or unsafe practices which COULD result in severe per- sonal injury or death. CAUTION: Hazards or unsafe practices which COULD result in minor per- sonal injury or product or property damage. IMPORTANT: Indicates that equipment or property damage could result if instruc- tions are not followed. NOTE: Gives helpful information. Finn Corporation CALIFORNIA Proposition 65 Warning The engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm. CALIFORNIA Proposition 65 Warning Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

It is important that all operators of this machine are familiar with all of the safety aspects mentioned below and have read the entire Operator’s Manual before operating the machine. Always keep a copy of this manual with the machine. It is the responsibility of the operator of the machine to fully understand this safety sheet. Remember that YOU are the key to safety. Good safety practices protect not only you but also the people working with and around you. Keep in mind that this safety sheet is written for this type of machine only. Practice all other usual and customary safe working precautions; and above all, remember that safety is up to you. The FINN MULCH SPREADER is intended to be used as an applicator of vegetative hay or straw mulches onto the seedbed. Its use with other products or for other applications must be by approval of the product’s manufacturer. If there are any questions contact FINN Corporation at 1-800-543-7166. I. PRE-START EQUIPMENT CHECK (equipment check is to be made with the engine off): 1. Check hitch and hitch bolts, safety chains, lights, brakes and breakaway switch. Verify that the hitch ball is the correct size for the coupler. 2. Check that all guard rail- ing is in place and secure. 3. Verify that all guards are in place. 4. By carefully looking in the shredder box, inspect the shredder box for foreign objects. 5. With the ignition switch on, verify that the signal horn is operating correctly. 6. Make sure no one is working on or inside the machine. Signal “All Clear” before starting the engine. II. MACHINE OPERATION: 1. Always wear safety gog- gles when operating or feeding the machine. Other safety attire such as safe- ty shoes, ear protection, gloves, hard hats, dust masks, etc., should be worn as required by warn- ing decals on machine, operator’s manuals, or job- site requirements. Remove rings, watches, etc. Avoid loose fitting clothing that may get caught in rotating machinery. 2. Do not operate the machine without all guards in place. 3. Make sure the discharge spray area is clear of all persons, animals, etc. 4. The driver of the carrying or towing vehicle is responsible for the safety of the operator(s) and feeder(s) of the machine. Make sure the driver is aware of and avoids all possible hazards to the operator(s) on the machine, such as tree limbs, low power lines, etc. Vehicles on which equipment is mounted or towed must be started or stopped gradually. Avoid abrupt starts and stops. Never operate on a slope or a hill that may endanger the operator(s). All personnel should review and be familiar with start/stop signals between the driver and operator(s) before operation of the equipment. 5. Operator(s) of equipment should never ride on machine at speeds greater than 5 M.P.H. (8km/h). 6. Never operate machine in an enclosed area without venting the exhaust of both the equipment and the vehi- cle on which the equip- ment is mounted or towed. Deadly carbon monoxide fumes can accumulate. 7. Never operate this or any other machinery when fatigued, tired, under the influence of alcohol, illegal drugs or medication. You must be in good physical condition and mentally alert to operate this machine. 8. Never modify the machine. Never remove any part of the machine (except for service and then reinstall before operating).

of machine. Never mount or dismount a moving machine. 10. Do not aim discharge at people, animals, etc. Only aim the discharge at the intended seedbed. 11. Do not open any doors or access panels while machine is in operation. Severe injury may result from rotating parts. 12. Do not attempt to pull any- thing out of the feed chute or shredder box when machine is in operation. Shut down the engine, using OSHA lockout/ tagout procedure (29CFR 1910.147) before remov- ing any foreign objects. Signal “All Clear” before restarting the machine. III. MAINTENANCE: 1. Before servicing the machine, turn off engine and allow all moving parts to stop. Disconnect the battery cables to prevent accidental starting of the machine. Tag the engine operating area to show that the machine is being serviced. Use lockout/ tagout procedure (29 CFR 1910.147). 2. On trailer units perform general maintenance such as checking the safety chains, hitch and hitch bolts, tires, and brakes. Repair or replace if worn or broken. Never oper- ate machine on improperly inflated or damaged tires. Always use a safety cage or cable restraints when reinflating a repaired tire. 3. Radiator maintenance. Liquid cooling systems build up pressure as the engine gets hot. Before remov- ing the radiator cap, stop the engine and let the system cool. Remove the radiator cap only after the coolant is cool. 4. Battery maintenance. Lead-acid batteries contain sulfuric acid which damage eyes or skin on contact. Always wear a face shield to avoid acid in the eyes. If acid contacts eyes, flush immediately with clean water and get medical attention. Wear rubber gloves and protective clothing to keep acid off skin. Lead-acid batteries produce flammable and explosive gases. Keep arcs, sparks, flames, and lighted tobacco away. 5. Filling of fuel. Never fill the fuel tank with the engine running, while smoking or when near an open flame. Never smoke while handling fuel or working on the fuel system. The fumes in an empty container are explosive. Never cut or weld on fuel lines, tanks, or containers. Move at least 10 feet (3 meters) away from fueling point before starting engine. Wipe off any spilled fuel and let dry before starting engine NOTE: Be careful not to allow fuel, lubricant, hydraulic fluid, or cooling fluids to penetrate into the ground or be discharged into the water system. Collect all used fluids and dispose of them properly. 6. It is recommended that only authorized genuine FINN replacement parts be used on the machine. 7. Do not use ether cold start fluid if engine is equipped with glow plug type preheater or other intake mani- fold type preheater. It could cause an explosion or fire and severe injury or death. 8. Diesel fuel under pressure can penetrate the skin or eyes and cause injury, blindness or death. 9. Make certain that all decals on the machine are maintained in good legible condition. Replacement decals are available through FINN Corporation by specifying the part number shown in the lower right hand corner of the decal. See page 5 for the current set of safety decals mounted on the unit. See Parts Manual for the location and quantity of all decals on this unit.

P/N-31228 Both the single and double chains must be crossed under the tongue. They must be oriented in such a manner as to prevent the tongue from dropping to the ground in the event of failure to the hitch, coupler or ball. The Chains must be connected to the towing vehicle so that the slack for each length of chain, between the trailer and the towing vehicle, is the same and must have no more slack when in use than is necessary to permit proper turning of the vehicles. The forward end of the chain must be attached to the towing vehicle, not to the ball, but to the hitch or other frame member. The chain must be looped around the member and hooked back into itself. SAFETY CHAIN INSTALLATION P/N-31227 Always inspect tow vehicle and equipment hitch before towing. Tighten all hitch bolts and properly connect wiring and saftey chains. 23519 Wear eye protection around operating equipment. ฀ ฀ 20970 Personnel should not ride this equipment฀฀ at speeds greater than 5 MPH (8 km/h). ฀ ฀ 12179 ฀ Do not operate without guards in place. ฀ ฀ 12251 ฀ Rotating fan hazard.฀ Keep hands clear.฀ Shut off engine before servicing. ฀ ฀ 012279 To prevent serious burning or scalding:฀ • Pressurized cooling system.฀ • Allow system to cool.฀ • Remove cap slowly with gloves on. ฀ ฀ 22357 Turn engine off, disconnect battery, and allow all moving parts to stop before servicing equipment. HOT EXHAUST 012278 CAUTION USE ON 2" BALL ONLY P/N 31336

Manual for B-70 Mulch Spreader INTRODUCTION: This manual is designed for step by step instructions of the operation, care, and maintenance of the B-70 Mulch Spreader and, in addition, it contains illustration and descriptions of a complete list of parts and components for easy identification. For best results and to insure longer life of the equipment, please follow the instructions carefully. For your safety read the entire manual before operation of this unit. DEFINITION OF MULCHING: Mulching is the process whereby a vegetative mulch such as hay or straw, sometimes excelsior or other wood product or other vegetative material is spread on previously seeded areas to promote germination, while providing temporary erosion control. THE FINN B-70 MULCH SPREADER AND HOW IT WORKS: The FINN B-70 Mulch Spreader will apply vegetative mulch at a fast and uniform rate (with the specified amount of adhesive material, if so desired) utilizing a minimum amount of manpower. The baled vegetative mulch material is placed on the feed chute and separated by the bale feeder as he feeds these bales into the shredder housing. In the shredder housing a combination of beater chains and air cur- rents separates the mulch into individual fibers, which are drawn into the blower housing and blown through the discharge assembly onto the seedbed. TOWING VEHICLE: The truck used to tow the Finn B-70 Mulch Spreader should have a bed large enough to carry the quantity of mulch needed for economical operation. The truck must be equipped with a ball or pintle type hitch to tow the Mulch Spreader. This hitch should be mounted as near to the end of the truck bed as possible. Use a 2” ball rated 6000 lbs. (2721 kg). The tow vehicle must be able to support 600 lbs. (272 kg) down on its hitch. LOADING BALES: Load the bales of mulch on the truck bed with binder twine or wire on top rather than on the side. This makes it easier to grab the bales while the Mulch Spreader is in operation. Place the first layer of bales “lengthwise” on the truck. The second layer of bales should be placed “cross- wise”. Alternate successive layers lengthwise and crosswise in order to secure the load. Leave enough room at the rear of the truck bed for the bale handler to stand.

1. A. Skid Unit - Check condition of all mounting hardware securing the Mulch Spreader to the truck bed. B. Trailer Unit - Inspect hitch, safety chains, lights, brakes and breakaway switch. 2. Check the signal horn for proper operation. 3. Inspect that all railings are in place and secure. 4. Insure that all guards are in place. EQUIPMENT CHECK: CAUTION: Equipment check is made with the engine off and all rotating parts stopped. 1. Tool kit - see that it contains all prescribed items (see tool kit list page 30). 2. Check shredder box for foreign objects that could damage the equipment or injure workers. 3. Check fuel tank. Use 2-D diesel fuel oil. If operating at ambient temperature below 40ºF (4ºC) or at an altitude exceeding 5000 feet (1524m) use No. 1-D fuel oil. 4. Check engine oil - refer to engine operator’s manual. 5. Check liquid level in radiator and overflow tank. 6. Inspect air cleaner for dust and dirt - refer to engine operator’s manual. 7. Engage and disengage clutch to determine if it “snaps” in and out of engagement. 8. Check beater chains and their mounting pins for damage or wear. Replace if necessary. 9. Lubricate equipment - use hand gun only (see lube chart page 9). 10. When not using an adhesive, remove the belt that drives the asphalt pump (running the pump dry will permanently damage it). STARTING PROCEDURE: CAUTION: See safety section of the manual (pages 1-4) before operating the machine. 1. Disengage the clutch. 2. Set throttle about ¼ open. 3. Turn key counter clockwise and hold until the glow plug indicator light goes out. 4. While holding in the safety switch button, turn the key clockwise until the starter engages, and the engine starts. 5. Continue to hold safety switch in for approximately 10 seconds. Allow the engine to warm up for 3 to 5 minutes. NOTE: This engine has a safety system that will shut the engine off if the engine oil pressure drops below 7 psi. or if the water temperature reaches 230° Fahrenheit (110° Centigrade).

let the governor control the engine speed. CREW MEMBERS AND THEIR DUTIES: 1. The Operator controls the placement of the mulch on the seedbed by moving the discharge assembly. He also controls the movement of the towing truck along the seedbed by using a predetermined set of signals with the signal horn. 2. The Bale Handler operates from the truck bed and supplies the feeder with bales of mulch material, cut side up. 3. The Bale Feeder cuts and disposes of the twine or wire; separates the bale in 1½” to 2” bats and feeds those into the shredder box allowing about a 10” space between bats. Uniform feeding assures fast separation and more uniform application. 4. The Truck Driver follows the directions of the operator for the movement of the towing truck. The truck driver should be cautious in starting or stopping the truck so that the crew members are not thrown off balance. BLOWER DISCHARGE: The B-70 Mulch Spreader should be towed to a point approximately 30 ft (9 m) from the area where the mulch is to be applied. The operator elevates the discharge spout about 10º above the plain of the seedbed so that the mulch floats onto the seedbed. Do not drive the mulch into the seedbed with air pressure. The higher the tube is held, the more uniform the application will be. A full circle horizontal travel of the discharge spout allows the operator to vary the direction of the discharge spout according to the prevailing winds. The tube should never be directed into the wind, towards any per- sons, or at the towing vehicle. Use the engine throttle to control the distance of the mulch. Except for the side feed model the shredder box cover (see page 16 for picture) has two positions. The lower position directs material more quickly to the blower blade and provides higher capacity with bright straw. The upper position is better for most hay materials since it retains the material in the shredder box longer for more even distribution. The unit is shipped with the cover in the lower position. Your B-70 Mulch Spreader has a beater roll on the extended blower shaft. Mounted on this beater roll are four beater chains installed opposite each other. This arrangement will work well for most materials. If a longer discharged fiber length is desired, remove two opposite chains. CAUTION: Be sure beater chains are mounted opposite each other at all times to avoid throwing the blower shaft out of balance. If any obstruction stops the flow of mulch, immediately disengage clutch and shut off engine. Do not reach into the beater box or attempt any adjustment until the engine and all rotating parts have stopped. When the obstruction has been removed, the motor can be restarted and mulch application can continue. DANGER: Do not reach into the beater box or attempt any adjustment until the engine and all rotating parts have stopped.

AFTER FIRST 4 - 8 HOURS OPERATION: 1. Check and adjust clutch - see page 10. 2. Retorque wheel lugs - again after 7 days. (Trailer option only). DAILY CLEAN-UP MAINTENANCE: Follow this procedure daily to keep the equipment in good operating condition: 1. Clean the air cleaner following the instructions in the engine operator’s manual. 2. Check air cleaner connections. If they come loose or disconnected, warranty on your engine is subject to cancellation. 3. Clean the radiator and radiator guard with tap water. 4. Clean the beater chains, making sure to remove all twine, wire, and other foreign objects. Check pins and nuts. 5. Lock the discharge tube into place. 6. Check engine oil level. 7. Check hitch bolts and safety chains. 8. Remove asphalt emulsion strainer screen. Clean and re-install. 9. If the asphalt emulsion system has been used, the cleaning procedure previously described should be followed. WEEKLY MAINTENANCE: After each 50 hours of operation, follow this procedure: 1. Change engine oil, following engine manufacturer’s recommendations after the first 50 hours and then every 200 hours thereafter. 2. Change the engine oil filter cartridge with every oil change (once every 200 hours). 3. Lubricate bearings with general-purpose chassis lubricant, using a grease gun. Wipe each bearing before lubrication to remove dirt and prevent overheating. 4. Inflate tires to 35 pounds. 5. Check clutch adjustment to insure that it “snaps” in and out of engagement. CAUTION: Adjust only while engine is off.

Ref. No. Location Lubricant Frequency Number 1. Grease drive shaft bearings CL Weekly 2 2. Repack wheel bearings CL Annually 2 3. Check engine oil level MO Daily 1 4. Check air cleaner MO Daily 1 5. Change engine oil & filter MO See Eng. Manual 1 6. Grease clutch shaft bearings CL Daily 1 7. Grease clutch lever bearing CL Daily 1 8. Change engine coolant AF Seasonally 1 9. Check fuel tank level DF Daily 1 10. Check engine coolant AF Daily 1 LUBRICANT OF FLUID USED CL Chassis Lubricant MO Motor oil SAE 30 CD/SF AF 50/50 Anti-freeze and water mixture DF Diesel Fuel TIME KEY FLUID CAPACITIES DAILY Fuel - 13.5 gallons WEEKLY Engine Oil - See engine manual SEASONALLY (OR 500 HOURS) Engine Coolant - (50/50 anti-freeze ANNUALLY and water mixture) 4 gallons SEE ENGINE MANUAL 1 2 3 4 5 6 7 8 9 10

This is a short simple outline of the Twin Disk clutch adjustment and lubrication. When preforming mainte- nance beyond this brief outline refer to the Twin Disk Care and Operations manual. In order to properly identify parts when ordering replacement parts, always refer to unit and specification number stamped on the name plate located on the top center of the power take-off housing. LUBRICATION: The Twin Disk clutch is equipped with life-time-lubrication internal bearings and should not be lubricated. The operating shaft bearing located where the drive shaft exits the clutch housing should however be lubri- cated every 1-3 months depending on usage. The clutch engage lever shaft should be lubricated weekly. ADJUSTMENT: If the clutch does not pull, heats, or operating lever jumps out of engagement, the clutch must be adjusted. To adjust the clutch remove the name plate in plate located on the top center of the power take-off housing. Turn the clutch shaft assembly until the adjusting lock pin can be reached. Disengage the adjusting lock pin and turn the adjusting yoke or ring to the right or clockwise until the clutch lever requires a distinct pres- sure to engage (approx. 26 lbs of pull). A new clutch generally requires several adjustments until the friction surfaces are worn in. After the clutch is "worn in" the adjustment should be checked regularly. NOTE: Do not adjust clutch too tight. Over tightening can cause component failure.

SERIAL NUMBER OF MACHINE 6 16 4 19 18 10 8F 1 14 2 3 5 9 7 17 13 12 11 15 8D 8C 8A 8B 8E

SERIAL NUMBER OF MACHINE DISCHARGE ASSEMBLY Ref. No. Part Number Description No. Req’d 1 031247 Transition Assembly 1 2 031018-01 Elbow Bearing 3 3 031086 Transition Seal 1 031109 Seal Banding 32” 4 031243-08 Elbow Hinge Rod 1 5 031239 Elbow Assembly 1 6 031241 Elbow Handle 1 7 031242-03 Elbow Seal-Upper 2 8 031341 Seal Plate Assembly 1 8A 031338-01 Seal Plate Hinge 1 8B 031238-04 Seal Plate 1 8C 031338-08 Side Seal 2 8D 031338-07 Side Seal Retaining Strap 2 8E 031338-03 End Flap Seal Retaining Strap 1 8F 031338-04 End Flap Seal 1 9 031238-05 Hinge Seal 1 10 031240 Discharge Tube 1 11 031242-04 Elbow Seal-Lower 2 12 031242-07 Elbow Seal Retainer Strap 2 13 031243-01 Discharge Tube Hold Down Bracket 1 14 031243-04 Discharge Tube Hold Down Arm 1 15 031245 Snapper Pin 1 16 031243-07 Elbow Tensioning Rod 1 17 031258 Lever Nut 1 18 031338-09 Top Seal 1 19 031338-10 Top Seal Retaining Strap 1 20 031338-12 Side Elbow Seal 2 21 031338-11 Hinge Seal 1

SERIAL NUMBER OF MACHINE SHREDDER BOX AND FEED CHUTE (STANDARD TRAILER MODEL) Ref. No. Part Number Description No. Req’d 1 031287 Shredder Box 1 2 031284 Shredder Box Cover 1 3 031158-04 Feed Chute Hinge Pin w/ Nuts 2 4 031157 Feed Chute 1 5 031158-05 Feed Chute Stop w/ Nuts 1 6 030898 Feed Chute Extension 1 7 031184-01 Upper Feed Chute Stand 1 8 031184-03 Lower Feed Chute Stand 1 9 FW71225 Snapper Pin 1 10 031096-01 Shredder Door 1 11 031096-04 Shredder Door Hinge Pin w/Nut 1 1 2 3 4 5 6 7 8 10 11 3 9

SERIAL NUMBER OF MACHINE SHREDDER BOX AND FEED CHUTE (R-H SKID MODEL) Ref. No. Part Number Description No. Req’d 1 031292 Shredder Box Weldment 1 2 031293 Feed Chute Weldment 1 3 031289-01 Feed Chute Cover 1 4 031294 Feed Chute Extension 1 5 031295-01 Door Weldment 1 6 031096-04 Hinge Pin 1 031295-04 Left Leg Weldment 1 031295-05 Right Leg Weldment 1 6 5 4 3 1 2

SERIAL NUMBER OF MACHINE BLOWER AND DRIVE Ref. No. Part Number Description No. Req’d 1 000527 Sheave, Motor 1 1A 020362B Bushing, Motor 1 2 031273 Coupling Half, Motor 1 3 031272 Coupling Half, Blower 1 4 031274 Coupling Insert 1 5 030712 Bearing 2 6 030904 Blower Shaft 1 7 031029 Blower Blade w/Hub 1 7A 030877 Blower Hub 1 030874 Key, Bushing to Shaft 1 030873 Key, Hub to Bushing 1 8 030950 Beater Roll Assembly 1 8A 030872 Beater Roll Hub 1 8B 030876 Beater Roll Bushing 1 8C 020111 Chain 4 8D 020119 Beater Bolt 4 022487 Flex Nut 4 031278 Coupling Guard 1 031389 Tool Box 1 1 1A 2 4 3 5 6 7 7A 8 8A 8B 8C 8D

SERIAL NUMBER OF MACHINE TRAILER WIRING Ref. No. Part No. Description No. Req'd 031210 Trailer Wiring Harness 1 1 060069 Trailer Plug 1 2 023424 Breakaway Switch 1 3 005138 Right Tail Light 1 4 005137 Left Tail Light 1 5 005236 License Light 1 004720 License Plate Bracket 1 TM GD A LT RT S GROUND (WHITE) LEFT TURN (YELLOW) RIGHT TURN (GREEN) NOT USED BRAKES (BLACK) RUNNING LIGHTS (BROWN) Female Coupler Looking at Terminal End RED RED BLACK BROWN WHITE GREEN YELLOW STARTER BLACK BROWN BROWN 1 2 BROWN BROWN RED RED BLACK WHITE WHITE BLACK 4 3 5

SERIAL NUMBER OF MACHINE TRAILER ASSEMBLY Ref. No. Part No. Description No. Req’d. 1 031205 Platform Assembly 1 2 031183-01 Guard Rail-Right 1 3 031183-02 Guard Rail-Left 1 4 031189 Jack 1 5 031202 2” Ball Hitch Assembly 1 030482 2” Ball (Optional) 6 031196-01 Fender Assembly - Right 1 031196-02 Fender Assembly - Left 1 7 031167 Axle Assembly 1 031220 Axle Shim Plate 2 8 031221 Complete Hub Assembly 2 WL9103305 Grease Seal 2 WLLM68149 Bearing, Inner Cone 2 WLL68111 Inner Cup 2 WL9080607 Hub/Drum 2 WLL44610 Outer Cup 2 WLL44649 Bearing, Outer Cup 2 WL90509 Spindle Washer 2 WL90601 Spindle Nut 2 WL91901 Cotter Pin 2 WL92102 Grease Cap 2 WL9251510 Wheel Stud 2 WL90608 Wheel Nut 2 031222 Right Brake Assembly 1 031223 Left Brake Assembly 1 9 031187 Wheel 2 031188 Tire 2 031179 Safety Chain 2 031180 Clevis Grab Hook 2 031181 Chain Connecting Link 2 10 031269 Bumper (Not Shown) 1

SERIAL NUMBER OF MACHINE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

SERIAL NUMBER OF MACHINE ENGINE PARTS Ref. No. Part Number Description No. Req'd 1 031390 Kubota V1505B-86 Engine 1 2 031452 Clutch Assembly 1 031219 Clutch Arm 1 031444 Clutch Handle 1 3 031424 Engine Mount 1 031376 Center Bushing Mount 4 055505 Snubbing Washer 4 4 031400 Engine Cradle Weldment 1 5 031395 Engine Top Cover 1 6 031419 Engine Cover Lid 1 7 031404-01 Engine Lid Hinge 1 8 031402 Radiator Shroud 1 9 031403 Radiator Screen 1 190087 Screen Rubber Trim 1.5’ 10 KU16665-72061 Radiator Assembly 1 031444 Upper Radiator Hose 1 031445 Lower Radiator Hose 1 KU16285-74110 Fan 1 11 KU15224-43018 Fuel Filter Assembly 1 KU7000-43081 Filter Element 1 005502-01 Filter Support Arm 1 080105 Pre-Fuel Filter 1 12 080103 Fuel Pump 1 13 KU16616-11010 Air Cleaner Assembly 1 KU15741-11080 Element 1 031356 Pre Cleaner 1 055548 Mounting Band 2 031376 Rubber Shock Mount 4 14 031397-02 Throttle Plate 1 005176 Throttle Cable 1 007675 Ball Joint 1 15 KU155501-72400 Coolant Recovery Tank w/Bracket 1 16 006499 Horn & Bracket 1 17 023758 Soft Latch 2 KU37410-88518 Muffler 1 055568 Temperature Switch 1 KU16271-32090 Oil Filter 1 031197 Fuel Tank 1 007914 Fuel Cap 1 031215 Fuel Level Gauge 1 031197-06 Fuel Suction Tube 1

SERIAL NUMBER OF MACHINE POWER TAKE OFF ASSEMBLY Ref. No. Part No. Description No Req'd 1 TD6939 Ring, Driving 1 2 TDM141A Piolt Bearing 1 3 TD2727 Nut 1 4 TDA1587 Lock washer 1 5 Clutch Assembly (includes: a thur f) 1 a Hub and Back Plate Assembly 1 a-1 TD110 D3 Pin, Plate 1 a-2 TDA3024 Hub Plate 1 b TDA2286 Clutch Release Spring 6 c TDA3507E Clutch Plate 1 d TD3951 Flotaing Plate 1 e Adjusting Yoke Assembly 1 e-1 TD2042 Adjusting Lock Pin 1 e-2 TD1382 Adjusting Lock Pin Spring 1 e-3 TD3206 Adjusting Yoke 1 e-4 TDB1535B Cotter Pin 4 e-5 TD2411 Finger Lever 4 e-6 TD110 D-3 Finger Lever Pin 4 f Sliding Sleeve Assembly 1 f-1 TDB1535B Cotter PIn 7 f-2 TDB1390 Slinding Sleeve 1 f-3 TDB1535B Cottor Pin 4 f-4 TD2968 Finger Lever Link 8 f-5 TDB1537B Finger Lever Link Pin 4 f-6 TDB1537C Link Pin 4 f-7 TDB1048D Internal Retaining Snap Ring 1 f-8 TDM1921 Ball Bearing 1 f-9 TDA4173A Collar 1 f-10 TDA2915L External Retaining Snap Ring 1 6 TDM2001E 5/16-18 x 5/8 Bolt 4 7 TDM2046L 5/16 Flat Washer 4 8 TDA1181 Bearing Retainer 1 9 TDA1002 Snap Ring, External 1 10 TDM177A Ball Bearing 1 11 TDM2032X Hub Key 1 12 TDA3026AK Shaft 1 13 TDM2032BE Shaft Key 1 14 Name Plate Gasket 1 15 TD1965D Name Plate 1 16 TDM2023F Screw 2 17 031219 Clutch Handle 1

SERIAL NUMBER OF MACHINE 50 30 STARTER BATTERY ALTERNATOR GLOW PLUGS FUEL PUMP HORN TEMPERATURE GAUGE OIL SWITCH BATTERY CABLE GROUND STRAP 12 Ga. BLUE BLACK BROWN WHITE YELLOW GREEN BLACK ORANGE BLACK RED 12 Ga. BLACK BROWN BLUE RED RED GREEN BLUE SHUT DOWN SYSTEM BLUE BLACK WHITE 5 4 3 2 1 10 9 8 7 6 Orange Brown Green Blue Red Blue Black Green Yellow Red Black 12 Ga. 16 Ga. 12 Ga. 16 Ga.

SERIAL NUMBER OF MACHINE ENGINE WIRING HARNESS Part No. Description No. Req’d. 005687 Wiring Harness 1 002256-12 Battery 1 080096 Battery Cable 1 031350 Ground Strap 1 006499 Horn Assembly 1 007274 Hourmeter 1 020886 Horn Button 1 055568 Temperature Switch 1 022119 Safety Switch 1 KU66706-55120 Ignition Switch 1 004934 Oil Switch 1 KU15403-64490 Glow Plug Indicator Light 1 080103 Fuel Pump 1 170028 Fuse with Holder 1 KU15694-65990 Glow Plug Timer 1 006245 Generator Light 1 031368 Battery Holddown Strap 1 005561 Electrical Housing 1 023602 Electrical Housing Insert 1

SERIAL NUMBER OF MACHINE B S C 50 17 19 30 AC BLACK RED RED YELLOW YELLOW/BLACK BROWN/BLACK BLUE BLUE RED/BLACK BLUE/BLACK ORANGE/BLACK BROWN ORANGE ORANGE BLACK BLACK/RED RED ORANGE BLACK GREEN RED YELLOW BLACK HOURMETER GROUND TIMER HORN GLOW PLUG INDICATOR GEN LIGHT IGN SAFETY SWITCH 5 4 3 2 1 10 9 8 7 6 Blue Brown/ Black Yellow/ Black Yellow Red Orange Brown Orange/ Black Blue/ Black Red/ Black Black Red Black/ BUTTON

SERIAL NUMBER OF MACHINE CONTROL BOX WIRING Part No. Description No. Req'd 007274 Hour Meter 1 022119 Safety Switch 1 KU15694-65592 Glow Plug Timer 1 020886 Horn Button 1 KU15403-64491 Glow Plug Indicator Light 1 006245 Generator Light 1 KU66706-55120 Ignition Switch 1 023604 Electrical Housing 1 023601 Electrical Housing Plug 1 080304 Liquid Tight Fitting 3 005589 Control Box Wiring Harness 1

SERIAL NUMBER OF MACHINE 1 1A 9 8 2 3 17 18 23 24 19 21 4 25 5 16 12 11 4 6 7 14 15 13

SERIAL NUMBER OF MACHINE B70 DECALS Ref. No. Part No. Description No. Req'd 1 011690 Finn Name Plate 1 1A 031235 “Finn” Decal 2 2 020976 Patent Infringement 1 3 031168 Patent Numbers 1 4 022357 Caution: Turn Off Engine 2 5 031297 Important: Clutch Adjustment 1 6 020068 Danger: Do Not Open 1 7 022690 Caution: Eye Protection 1 8 020970 Caution: Do Not Ride Over 5MPH 1 9 023519 Caution: Wear Eye Protection 1 10 006870-HORN “HORN” 1* 11 080442 “Throttle” 1 12 007231 “Service Weekly” 5 13 031227 Caution: Tighten Hitch 1 14 023423 Warning: Breakaway Switch 1 15 031228 Caution: Safety Chain Installed 1 16 012179 Warning: Do Not Operate 1 17 023391 “Diesel Fuel Only” 1 18 007351 “Hand Gun Only” 1 19 007429 “Radiator Protection” 1 20 006870-GEN “Gen” 1* 21 012260 Maintain Decals Plate 1 22 080108-03 “Glow Plug” 1* 23 012251 Warning: Rotating Fan Hazard 2 24 012279 Warning: Radiator Cap 1 25 012278 Danger: Hot Exhaust 1 26 022082 “Hold Button In For 10 Seconds” 1* *: Not Shown Located On control Box Face. Note: 150028 Decal kit includes all decals reference numbers 2 through 26.

SERIAL NUMBER OF MACHINE TOOL KIT Part No. Description No Req’d. 020057 #13 Twine Knife 1 020063 #11 Twine Knife 1 Manual, Engine 1 Manual, Parts & Operation 1

attachments therefore manufactured by Finn to be free from defects in material and workmanship for a period of 12 months from date of purchase or 1200 hours of use, whichever comes first. Replacement parts provided under the terms of this warranty are warranted for the remainder of the warranty period applicable to the product in which installed, as if such parts were original components of that product. Finn makes no warranty with respect to (a) allied equipment or trade accessories not manufactured by it (such as, but not limited to tires, ignitions, starters, hose, batteries, magnetos, carburetors, engines or like or unlike equipment or accessories), such being subject to the warranty, if any, provided by their respective manufactures; or (b) secondhand, used, altered, or rebuilt machines. Further, the warranty herein expressed shall be rendered null and void to the extent any defect or failure of the products warranted hereby arises out of or is caused by accessories or component parts not manufactured or supplied by Finn, whether same are supplied by Purchaser, dealers or any other party. THE WARRANTY DESCRIBED IN THIS PARAGRAPH SHALL BE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Upon notification of Finn during the above-stated warranty period of any failure to conform to this warranty, and upon inspection by Finn to verify said nonconformity and verify the continuing existence of the warranty period, Finn will provide a new part or a repaired part, whichever Finn elects, to replace the part found to be defective. Such parts will be provided without charge to the Purchaser during normal working hours at a place of business of a Finn dealer or other establishment authorized by Finn to effect said repairs or replacements, but Purchaser shall bear all costs of transporting the product to and from such place of business or establishment. Correction of nonconformities, in the manner and for the period time provided above, shall constitute fulfillment of all liabilities of Finn under this contract. THE REMEDIES OF THE USER SET FORTH HEREIN ARE EXCLUSIVE, WITHOUT REGARD TO WHETHER ANY DEFECT WAS DISCOVERABLE OR LATENT AT THE TIME OF DELIVERY OF THE PRODUCT TO THE PURCHASER. The essential purpose of this exclusive remedy shall be to provide the Purchaser with repair or replacement of parts that prove to be defective within the period and under the conditions previously set forth. This exclusive remedy shall not have failed of its essential purpose (as that term is used in the Uniform Commercial Code) provided Finn remains willing to repair or replace defective parts within a commercially reasonable time after it obtains actual knowledge of the existence of a particular defect. IN NO EVENT SHALL FINN BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL OR INDIRECT DAMAGES, INCLUDING LOST PROFITS OR LOST COMMERCIAL OPPORTUNITIES, WITH RESPECT TO THE SALE OF THE ABOVE WARRANTED PRODUCT OR ANYTHING DONE TN CONNECTION THEREWITH, OR FOR PROPERTY DAMAGE SUSTAINED BY A PERSON CLAIMING TO BE A THIRD PART BENEFICIARY OF A SURVIVING WARRANTY UNDER THE LAW OF ANY JURISDICTION. NOTICE FINN CORPORATION URGES THE USE OF ONLY FINN CORPORATION SUPPLIED PARTS AND ATTACHMENTS TO ASSURE PROPER PERFORMANCE AND SAFE OPERATION OF FINN CORPORATION EQUIPMENT. INSIST ON PARTS AND ATTACHMENTS MANUFACTURED OR SUPPLIED BY FINN CORPORATION WHEN YOU PURCHASE, REPAIR OR REPLACE YOUR FINN EQUIPMENT AND ATTACHMENTS. BECAUSE FINN CORPORATION CANNOT ASSURE THAT PARTS AND ATTACHMENTS NOT MANUFACTURED OR SUPPLIED BY FINN MEET FINN CORPORATION'S QUALITY STANDARDS, SPECIFICATIONS, OR OPERATING REQUIREMENTS, OUR WARRANTY IS NOT EFFECTIVE TO THE EXTENT ANY FAILURE OF OR DEFECT IN A FINN CORPORATION PRODUCT ARISES FROM OR IS CAUSED BY PARTS, ATTACHMENTS OR COMPONENTS NOT ORIGINATING WITH FINN CORPORATION. USE OF FINN CORPORATION EQUIPMENT WITH PARTS AND ATTACHMENTS NOT MANUFACTURED OR SUPPLIED BY FINN COULD RESULT IN PERSONAL INJURY. Effective December 8, 1995 CALIFORNIA Proposition 65 Warning The engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm. CALIFORNIA Proposition 65 Warning Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.