Creative Playthings 63080-101 Instructions Manual

Text of Creative Playthings 63080-101 Instructions Manual

A 1 35200-102 Swing Mount 4 x 4 x 35-1/2"

B 1 35242-102 Leg Brace 4 x 4 x 55-1/2" C 1 35303-102 Center Block 2-3/4 x 3-1/4 x 8" D 1 35304-102 Side Block One 4 x 4 x 13-1/4" E 1 35305-102 Side Block Two 4 x 4 x 13-1/4" F 1 40594-102 3 Position Beam Assembly G 2 40595-102 Leg Assembly H 1 14162-400 8" L-Brace, Green, Large Holes Classic Pine Swing Beam Model: 63080-101 CPSC recommends a safe play zone in front of and behind the swings that is twice th

Classic Pine Swing Beam Instructions - 19928-100A (01/16)

Copyright 2016, Creative Playthings - Printed in U.S.A. Page 2 Fasteners: 8 12002-206 5/16" Flat Washer 4 17036-1002 5/16 x 2-1/2" Lag Screw 4 17036-2202 5/16 x 5-1/2" Lag Screw 6 17020-113 Screw #10 x 2-1/2" 4 12002-207 Flat Washer 3/8 4 12017-207 Lock Washer 3/8 4 17001-103 Weld Nut 3/8" 1 17003-1213 Hex Bolt 3/8 x 3" 2 17003-1413 Hex Bolt 3/8 x 3-1/2" 1 17003-2613 Hex Bolt 3/8 x 6-1/2" 4 1200
Classic Pine Swing Beam Instructions - 19928-100A (01/16) Copyright 2016, Creative Playthings - Printed in U.S.A. Page 3 STEP TWO - Swing Hangers Place the Beam (F) on the ground with the holes for the Swing Hangers face up. Place the Beam approximately 90" from the side of the gym with the Swing Mount. Carefully follow the instruction included with the Swing Hang- ers to install the Swing Hangers in the positions shown. STEP THREE - Block Assembly STEP
Classic Pine Swing Beam Instructions - 19928-100A (01/16) Copyright 2016, Creative Playthings - Printed in U.S.A. Page 4 STEP FIVE - Secure Brackets STEP FOUR - Legs and Brackets Fasten two HD Angle Brackets (J) and two Leg As- semblies (G) to the Center Block as shown. Use one 1/2 x 10" Hex Bolt and one 1/2" Lock Nut to secure them. Do not use Flat Washers. Do not fully tighten the connection at this time so the parts will pivot on the bolt when erectin
Classic Pine Swing Beam Instructions - 19928-100A (01/16) Copyright 2016, Creative Playthings - Printed in U.S.A. Page 5 STEP SIX - Flip Beam With the help of others, flip the Beam end-over- end and lean the Beam against the side of the gym next to the Swing Mount. If there is a Wall Slat on the gym adjacent to the Swing Mount, remove it to avoid conflict during the following steps. Once the Beam is in place, replace the Wall Slat. STEP SEVEN - Beam to S
Classic Pine Swing Beam Instructions - 19928-100A (01/16) Copyright 2016, Creative Playthings - Printed in U.S.A. Page 6 STEP NINE - Leg Brace STEP TEN - Secure Top of Leg STEP ELEVEN - Secure Beam Retainer With helpers steadying the Legs, hold the Leg Brace (B) in the position shown. Make sure it is level and the ends do not overhang. Mark the position of the holes in the Leg Brace onto the Legs. Drill 1/4" diameter pilot holes 2" deep at the marks. Sec
Classic Pine Swing Beam Instructions - 19928-100A (01/16) Copyright 2016, Creative Playthings - Printed in U.S.A. Page 7 STEP TWELVE - Ground Stakes STEP THIRTEEN - Nameplate STEP FOURTEEN - Hang Swings Drive each Stake into the ground next to the Swing Beam Legs, as shown. Secure the Stakes directly into the base of the Leg Assemblies using two #10 x 2-1/2" Screws each. The top of the Stakes must not extend beyond the profile of the leg. Note: Do NOT us

Creative Playthings Play Sets & Playground Equipment Owners Instructions: