AUTEC Dynamic Series Instruction Manual

maintenance of the Radio Remote Control Original instructions Part B: Conformity and frequencies (863-870MHz and 915-928MHz) DYNAMIC+ SERIES LIUDT1004_eng-00 ...

warnings for the Conformity and frequencies (863-870MHz and 915-928MHz). The Manual consists of Part A – General, Part B – Conformity and Frequencies, Part C – Transmitting Unit, Part D – Receiving Unit and Part E – Battery and Battery Charger, plus the Technical Data Sheet. THIS MANUAL, INCLUDING ALL PARTS THEREOF, AND ALL INSTRUCTIONS CONTAINED HEREIN, MUST BE READ CAREFULLY AND UNDERSTOOD BEFORE INSTALLING, USING, MAINTAINING OR REPAIRING THE AUTEC RADIO REMOTE CONTROL. FAILURE TO READ AND COMPLY WITH ALL APPLICABLE WARNINGS AND INSTRUCTIONS OR ANY ONE OF TH ...

the Machine on which the Autec Radio Remote Control is to be installed and used to be certain that the structure, condition, organization and markings of the Machine as installed at the facility is appropriate for and will allow for the safe and reliable use and control of the Machine through the Autec Radio Remote Control interface. IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR DESIGN PROFESSIONALS, that the installation, maintenance and operation of the Autec Radio Remote Control and all of its components are done solely and completely in acc ...

OFFICERS, MANAGERS AND SUPERVISORS, to be certain that all Users of the Autec Radio Remote Control and that all Persons who are or will be working with or near the Machine operated by or through the Autec Radio Remote Control are fully and properly educated and trained by qualified Personnel in the proper and safe use of the Autec Radio Remote Control and of the Machine, including without limitation complete familiarity with and understanding of Autec warnings and instructions, and all applicable Laws, Regulations and Standards, even local, and that such Users and other Persons do i ...

1.1 Structure of the Instruction Manual ................................................................. 7 1.2 Caption and terminology ................................................................................. 9 1.3 Symbols ......................................................................................................... 9 1.4 To whom the instructions are addressed ...................................................... 10 1.5 Instruction storage ........................................................................... ...

Before reading this part of the Manual, you must read and understand the general part (Part A) of the Manual provided with the Radio Remote Control. The Manual for the use and maintenance of Autec Dynamic+ series Radio Remote Controls consists of different parts, that altogether form the Manual; the Manual must be read carefully, understood and applied by the Radio Remote Control's Owner, User and by all those Persons that, for any reasons, may operate with the Radio Remote Control or with the Machine where it is installed. 1.1 Structure of the Instruction Manual The following table describes the structure of t ...

Technical Data Sheet, that: -- describes the Transmitting Unit's configuration, -- indicates the relation between commands sent by the Transmitting Unit and those available on the Receiving Unit. Usage and maintenance instruction as a whole are to be considered as an integral part both of the Autec Radio Remote Control and of the Machine, system, device or Machinery system where the Radio Remote Control is installed. The Manufacturer of the Machine on which the Autec Radio Remote Control is installed, and the Owner and User of the Machine, must make sure that the Instruct ...

Contact Autec if any of the instructions, symbols, warnings or images are not clear and understandable, or if you have doubts or questions. In this part of the Manual, the terms listed below have the same meaning explained in the corresponding paragraph of the general part (Part A): -- Unit -- Radio Remote Control -- Transmitting Unit -- Receiving Unit -- Machine -- Manufacturer -- Installer -- User -- Maintenance Technician -- Manual or Instruction Manual -- Installation Manual -- Person -- Owner Functions indicated for the Manufacturer, the Installer, the User and the Maintenance Technician may be performed by a single Per ...

Addressees of instructions are listed in the paragraph with the same title in the general part: please refer to that part. 1.5 Instruction storage Regulation for the storage of instructions are described in the paragraph with the same title in the general part: please refer to that part. 1.6 Intellectual property Restrictions connected to intellectual property are described in the paragraph with the same title in the general part: please refer to that part. 10 LIUDT1004_eng-00 Information on the use of instructions AUTEC - Dynamic+ series ...

2.1 Series, Radio Remote Control and Unit Autec Dynamic+ series' Radio Remote Controls are designed to be used on Machines and provide a command interface to their command and control system, to be used from an appropriate distance and position. 2.2 Conformity with standards This part of the Manual describes: -- the Dynamic+ series' Radio Remote Control compliance with the standards, the requirements and conditions of use in each Country and -- the different frequency bands, in which the Radio Remote Control is able to operate. 2.3 Contacts and useful addresses The Radio Remote Controls are produced by Autec srl – Via Pom ...

-- make sure that the Radio Remote Control works within the frequency band permitted in the country where it is used; -- make sure that the Radio Remote Control works correctly, in compliance with the applicable standards in the relevant country; -- not modify the Radio Remote Control conformity, by performing modifications or technical operations that change its operation. During training on or usage of Autec Radio Remote Controls, local provisions imposing the conservation of product conformity with local standards must be respected, as well as specific standards related to safety in the use of Radio Remo ...

Model DJR Type NJ235 OQA-DJRNJ235 9061A-DJRNJ235 DJS Transmitting Unit Model DJS Type NJ035 OQA-DJSNJ035 9061A-DJSNJ035 CRD Receiving Unit Model CRD Type NK035 OQA-CRDNK035 d 9061A-CRDNK035 a b c a. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. b. Th ...

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the User’s authority to operate the equipment. 3.2.2 Industry Canada (IC) This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interferen ...

870MHz or 915-928MHz. The Radio Remote Controls' working frequency is defined by market-specific laws and standards. In order for the system “Machine+Radio Remote Control” to be compliant and therefore to be used, these laws and standards must be respected: if they are not, the Radio Remote Control cannot and must not be used. Autec cannot be held responsible if the Radio Remote Control is set with frequencies that are forbidden in the country of use. 4.1 863-870MHz frequency band 4.1.1 Frequencies The radio link between the Units of Autec Dynamic+ ...

4.2.1 Frequencies The radio link between the Units of Autec Dynamic+ series Radio Remote Controls is established at one of the frequencies permitted by the USA and Australian standards in force when the system is put on the market. Frequencies used ......................................................................................................... 256 RF power (FCC) .......................................................................... meets FCC requirements Channel spacing ...................................................................................................... 50kHz The Units communicate with one ...

PH: +39 0444 901000 - Fax: +39 0444 901011 [email protected] - www.autecsafety.com MADE IN ITALY ...