Forward STM-8800 Operation & User’s Manual

Description....................................................................................................... 4 Safety instructions........................................................................................... 4 Safety of persons............................................................................................... 4 General information........................................................... ...

Spectrum........................................................................................................ 21 AV Setup........................................................................................................ 21 Disposal......................................................................................... ...

and easy alignment of satellite antennas. If a satellite is found, the meter shows it on the display and emits a audible signal. Signal strength and quality are displayed as numerical values and bar graphs. Another measurement value is the forward error correction (FEC) and the bit error rate (BER), Modulation error rate(MER),In addition, the picture ...

 Avoid low temperatures (below 0 °C) or to high humidity.  The TFT display can be damaged by mechanical impacts.  Avoid excessive input voltages. Do not operate with the device:  if it has visible damage,  if there are loose parts in the device,  if the device was located outdoors or in damp rooms a extended period of time. Appropriate Usage The measuring d ...

RF IN: Not connect DC 14V: Power supply port AV OUT: Connect this port to TV’S CVBS via AV cable HDMI: Connect this port to TV HDMI port via HDMI cable AV IN: Connect the port to other’s CVBS Cable ...

No. Description 1 LNB1-IN LNB2-IN Digital satellite signal input 2 LC-Display Display of the TV picture, the menu and the measured values 3 POWER-LED Display of the energy state: Operation: red: the measuring devise is switched on. Off: the measuring devise is switched off. In charge: Green: The battery is charged Red: The battery is full charged 4 LOCK-LED LED lights when a signal is received. 5 FUNCTION keys ...

a satellite antenna 9 Menu Display the main menu 10 AV Switch AV input or out put setup 11 ANGLE Display the calculation menu 12 SYSTEM Configuration of all system parameter. Display current AV setup. 13 POWER Switch on the power on at 2-3 second 14 SCAN Display the auto scan menu 15 OFF Switch off the power 16 T/R Switch the TV or Radio program display 17 SPTRUM Display the menu of spe ...

Attention! Storing or operating accumulator no more than 40° C. Not burning or damaging accumulator. Not taking accumulator to contact with water. Charging the battery The maximum battery charging time is approximately 12 hours. A charging circuit in the measuring device provides an optimal charge of the battery. The device is charged if it is ...

è Select the point system setting. è Confirm your selection using the OK button. Figure 2: System setting language Setup Press the SYSTEM button to change the menu language. _ Select the point Language setup. _ Choose your desired language using the ◄- or ►- button. _ After your selection press the EXIT button and follow the instructions on. ...

_ Select the point Factory Default. _ Press OK to make the factory setting Factory reset Attention! All programs and settings, configured by you, will be reset to delivery status. ...

satellite dish up. ð Press the FIND button to display the Satellite Finding menu. ð ð Figure 4: Satellite Finding ...

ð Press the ◄- or ►- button to select a LNB type.. ð Input the Frequency using the NUMERIC buttons.(press◄- or ► first, then input the number you want) ð Input the symbol rate using the NUMERIC buttons.(press◄- or ► first, then input the number you want) ð Press the ◄- or ►- button to select the polarisation. ð F1 button to enter the Dish Setup menu ð F2 butt ...

T/T2 antenna up. è Press the Menu to choice T/T2 Finer pic to display the T/T2 Finding menu.. Figure 5:T/T2 Finder munu Finding channels manual Figure 6:T/T2 Finding è Press the T/T2 Finder button to display the menu T/T2 finding. è Press the ◄- or ►- button to select Scan method at Manual/Auto.. è Press the ◄- or � ...

è Press the ◄- or ►- button to select the T/T2 frequency è Press the F1 button to back T/T2 Finder menu è Press F2 button to screen capture Lining T/T2 antenna up -> Press the T/T2 Finder button to display the menu T/T2 finding. è Choose a T/T2 Frequency and .Bandwidth è Turn the receiving antenna as long as the LOCK- LED lights, or the joists of the signal level and signal quality are green. Once a s ...

the case if the signal about a multicounter should be distributed to several buyers. The higher the C/N value, the better. The BER value behind “10E” is important. The higher, the better. The value should be minimal 10E-4. The optimum is > 10E-6. Installation Satellite setting _ Press the MENU button to display the main menu. _ Press the ▲- or ▼- button to mo ...

_ Press the ▲- or ▼- button to move to the desired item _ Press the ◄- or ►- button to modify the value of the selected item. Use the NUMERIC buttons if necessary. _Select Satellite: Satellite selection _LNB-Type: Univ-LNB1(9750-10600),Univ-LNB2(9750-10750),UNICABLE, 5150, 9750, 10750, 11300, 10700, _22K: AUTO, ON, OFF _LNB power (LNB-Tension): Off, Auto, 13V, 18V _DiSEqC-Level: - / DiSEqC 1.0 ...

_Motor Position:Press ◄- or ►button to choose the Motor positon at the off/1-64 _Movement style:Press ◄- or ►button to choose he movement style at the _Step/Continuous/1 second _Move left/Right:Press ◄- or ►button to choose move left or right _F1:To store sat positon _F2:To Expert motor settings _ Select the point Satellites Setup and press the OK button. ...

_ In the Scan method button ,press the ◄- or ►- button choose the scan method mode at the Atuo/Blind/Manal _ In the NIT Search button ,press the ◄- or ►- button choose the NIT search at the ON/OFF _ In the Kind of service button ,press the ◄- or ►- button choose the Kind of service mode at the All services/Only free services/Only encrypted ...

_Press the File viewer to play usb file _ Press the Updating- button or use the updating the sw _ Press the Backup Data to backup data Figure 12: SW updating ...