Happybeds Aurora 5FT Assembly Instructions Manual

Assembly Instructions www.happybeds.co.uk Important before assembly: . Health & Safety: . Read these instructions carefully before assembling or using the product. Please check the contents of the boxes before attempting to assemble this product. The instructions will have a checklist of parts and fittings. It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product, to avoid scratches and damaging t ...

when lifting. Never drag or push the pieces across a hard or stone floor as this will cause damage to the joints. Use a carpet or a rug for extra care. If you have problems assembling or have damaged or missing pieces, please contact us by visiting: https://www.happybeds.co.uk/customer-service (Not metal) These tools are not necessary, but may help to assemble certain part ...

H No Hardware List Qty Box 1 JCBB M6 x 20mm 8 pcs 2 JCBB M6 x 35mm 8 pcs 3 JCBC M6 x 45mm 12 pcs 4 JCBC M6 x 80mm 2 pcs 5 JCBB M8 x 20mm 20 pcs 6 JCBB M8 x 40mm 14 pcs 7 JCBB M8 x 45mm 6 pcs 8 M8 Spring Washer 6 pcs 9 M6 Flat Washer 8 pcs 3 10 M8 Flat Washer 14 pcs 11 M6 Hex Nuts 18 pcs 12 M8 Hex Nuts 6 pcs 13 Allen Key M4 1 pc 14 Allen Key M5 1 pc 15 M6 Spanner 1 pc 16 M8 Sp ...

To fix the leg (P) in to the headboard (A) and footboard (B). Page 4 of 10 3 JCBC M6 x 45mm 4 pcs 13 Allen Key M4 1 pc 17 Plastic Washer 4 pcs Step 2: To fix the left side rail (C) and right side rail (C) to the headboard (A) and footboard (B) you will need to use hardware parts 5 with the M5 allen key (14). 5 JCBB M8 x 20m ...

To assembler support cross bar leg (M) after cross bar I, II completed. Step 4: To fix the cross bar I (K), II (L) to the footboard (B), side rails (C), you will need to use hardware parts (1) and the M4 Allen Key (13). To attached the L Shape Metal Corner Bracket (18) to the footboard (B) and side rails (C) you will need to use ha ...

After the part (H) go inside the position, put back the M8 HEX Nut and tighten it using M8 Spanner (16). To install the complete set of (G) to the left and right side rail (C), you will need to use hardware 6 and 8 with Allen key M5 (14). To assemble part G, it is a must to make sure the hole go ...

the screw, please make sure part G is in same alignment in between left and right side of part G. DO NOT use any power tools as this may damage the bed frame and will invalidate any claims. Page 7 of 10 D E E 3 JCBC M6 x 45mm 8 pcs 4 JCBC M6 x 80mm 2 pcs 9 M6 Flat Washer 8 pcs ...

the screw, please make sure part G is in same alignment in between left and right side of part G. DO NOT use any power tools as this may damage the bed frame and will invalidate any claims. Page 8 of 10 * Please insert the screw balance in the middle of the hole. D G 14 7 D Do Not Use Power Tools 7 JCBC M8 x 45mm 6 pc ...

panel go direct to the headboard and continue the second pieces there after the first pieces was in right position. To assembler the wing (O) you will need to open the velco behind the headboard (A) as shown. DO NOT use any power tools as this may damage the bed frame and will invalidate any claims. Page 9 of 10 WARNING: Take c ...

Please dispose of all packaging safely. Wipe clean with a slightly damp cloth. Avoid the use of all household cleaners and abrasives. Periodically check all screw & fixings to ensure they are secure. When moving your product, carefully lift into place. Never drag or push the product across the floor as this will cause damage to the joints. If the product is used on hard flooring, such as wood or laminated floo ...