PXM PX804-T Operation & User’s Manual

1 Description...................................................................................................3 2 Safety conditions........................................................................................4 3 Information on version..............................................................................7 4 DMX connection.........................................................................................7 4.1 GLOB ...

lighting of museums exhibitions or trade fair displays. The precision cropping system allows you to control the luminous flux and adjust the illumination range to the size and position of the displayed object. Thanks to the application of the latest semiconductor COB type SSL LED light source and advanced control electronics, a high performance illuminator was made, which f ...

set all parameters of the device and read the information on the time and temperature of the lamp. The PX804-T illuminator supports the RDM protocol. 2 Safety conditions Caution! Before installing, connecting and using the lamp you have to absolutely read this document. The following symbols are used to underline important information on security on the product and in this manual. Da ...

at the light source with any optical devices that focus the light rays. Light is harmful to unprotected eyes, can cause irritation, eye damage or even loss of eyesight. While working outdoors in normal conditions, the housing unit can heat up to +65°C. Make sure that accidental contact with the device during use is impossible. In case of improper usage of the product it ...

7. All sudden shocks, particularly dropping, should be avoided. 8. The device cannot be used in places with temperature lower than +2°C or higher than +40°C. 9. Clear with damp cloth only. Above the temperature of +70°C the brightness of the lamp is reduced, which prevents overheating of the device. If the device reaches a temperature of +90°C, the lamp power will be completely reduce ...

The PX804-T lamp is available in several versions that differ, for example, in the angle of the lenses used. Below is a description of the PX 804 - T markings and their explanation: PX804-T – BB – YYY – Z BB – version YYY – CRI and color temperature: Z – housing colors: XL – large COB X30 – CRI 95, temp. 3000K 1 – gray 930 – CRI 90, temp. 3000K 2 – black 950 – CRI 90, temp. 5000K 3 – white 830 – C ...

Pulse Control 5 Manual change of lamps settings The lamp has been equipped with a button which allows for changing the brightness level. The button has been placed at the bottom part of the junction box, above the lamp reflector. The layout of the button and connectors for connecting the PX277 programmer has been shown in the figure below : 8 phase 3 phase 1 phase 2 neutral DMX + mass (GND) DMX - POWER SUPPLY ...

Depending on the situation, the LED signals the following messages : • lamp starting – rapid blinking of the LED for 2 seconds • DMX signal receipt – slow blinking of the brightness adjustment press button (with frequency of 1Hz) for the first minute after the receipt of the DMX signal • after starting up of the lamp with the lack of the DMX signal – the LED lights (conti ...

The PX804-T settings can be changed by connecting to the PX277 (PxArt+ Settings Controller) configurator. It allows in connection with PX804-T to define the following parameters: DMX address for brightness (in the range of 1 – 512) and device behavior in the absence of DMX signal (programmable scene). When the lamp is connected to the configurator, the PX804-T will restart. 6.1 Available parameters DMX Addr. – ...

of the module with LEDs, PWR time / ACT time – total lamp operation time / total lamp lighting time, Factory Default – factory reset in PX804-T: • DMX Addr: 001 • No Signal: Off ◦Scene: 128 • No Signal Time: 1.0 s • Smooth: Level 3 • Control Mode: 1ch MONO Firmware version – software version, Serial Number – serial number. 11 ...

PREV Channel: 1 Value: 0 * ENTER PX804-XL PxArt+ Frame ENTER DMX Addr. 001 (1ch) * NEXT DMX Addr. 001 (1ch) DMX Addr. 512 (1ch) * NEXT NEXT No Signal Off NEXT ENTER No Signal Off * NEXT No Signal Scene * NEXT No Signal On * No Signal Hold * Channel: 1 Value: 128 * NEXT Channel: 1 Value: 255 * Channel: 1 Value: 128 ENTER PREV No Signal Time 0.0 s * No Signal Time 1.0 s * NEXT No Signal Time 10.0 s * ENTER No Signal Time ...

First, insert the movable shutters at an angle into the appropriate pockets – visualization below. 13 ...

according to the diagram below. 14 ...

Opposite diaphragms must be put in pocket on the same level (upper or lower pocket). 15 shutter in the lower pocket shutter in the upper pocket ...

The PX804-T supports the DMX-RDM protocol. DMX protocol allows only of a one-way data transmission, while extension the RDM protocol can transmit information in two directions. This makes possibility of monitoring activities of the compatible devices. Thanks to RDM some available settings of compatible devices may be programmed using this protocol. List of RDM parameters supported by the PX804 -T : Parameter name PiD Descri ...

PERSONALITY * 0x00E0 DMX operational mode PERSONALITY_ DESCRIPTION 0x00E1 description of individual operational modes SENSOR_DEFINITION 0x0200 information on the selected temperature sensor SENSOR_VALUE 0x0201 information about sensors SMOOTH_OFF/1/2/3/4 * 0x801A selection of smoothing options NO_SIGNAL_OFF/ON/HLD/S * 0x801C behavior of the device when the DMX signal disappears ...

GLOBAL Trac Pulse Control ® end feed power cable DMX cable (shielded cable, two-core cable) adapter GLOBAL Trac GAC 600 18 ...

type PX804-T power supply 230V AC number of LEDs 1 (COB) power 27W PF (power factor) 0.94 max. increase of the housing temperature +50°C CRI index min. 80 lifetime of diode 50 000h cropping area max. 1.35 x 1.35m (at distance 3m) brightness regulation extension 0 – 100% control protocol DMX-512 / RDM available housing colors gray, black, white smoothing function (smooth) yes number of control channels 1 (brightness) mounting GLOBAL Tra ...