Prorack K682 Fitting Instructions Manual

Text of Prorack K682 Fitting Instructions Manual

Prorack K682 Fitting Instructions for Basic Carrier

x 4 x 4 x 4 x 8 x 4 x 2 x 2 x 4 x 4 x 4 x 4 Revision No: 1A 1

MAX kgs (lbs)

W/P WHD Holden Colorado 7 , 5dr SUV 13-+ NZ 75 kgs (165 lbs) 100 kgs (220 lbs) Colorado 7 , 5dr SUV 13-+ AU 75 kgs (165 lbs) 100 kgs (220 lbs) Chevrolet Trailblazer , 5dr SUV 13-+ ZA 75 kgs (165 lbs) 100 kgs (220 lbs) 2

First Time Installation

G Remove parts from inside the package and check. Contact your dealer if any parts are missing or damaged. G This kit fits type A, B, C and D. G These instructions show type A crossbar fitted. They also apply to type B, C and D. G Use keys to remove covers. 3

Prorack K682 G Use hex screwdriver to reverse adjusting

screw 10 turns. G Press adjusting screw and pull crossbar legs out. Refer to the crossbar instructions for crossbar adjustment method. G Ensure each end of the crossbar is adjusted equally. G Set bars to length (revert to rear of these instructions). G Clamps onto flush roof rail. Pins locate on inside of rail. 4

G Tighten adjusting screw to 5 Nm (3.7 ft lb).

G Remove plastic clamp block by gripping bar leg with fingers and push firmly with thumbs until clamp block drops out behind leg. G Remove both pins from each leg. Use tapered end of spanner located inside left hand cover to assist. 5

G Detach foot from leg. Store loose parts in a

safe place. G Repeat for all legs. G Select four feet assemblies and match the left and right assemblies to the left and right roof rack legs. G Assemble foot from kit into leg by pressing it down. G Ensure foot interlocks with leg. G Using short capscrew and washer, secure assembly onto leg (use Hex Screwdriver supplied with crossbar to assist) G Do not over tighten. G Repeat for all legs.

G Use two M5 x 12 mm self tapping screws to

secure the assembly onto the leg. G Do not over tighten. Fitment G Apply protective strip as shown. Trim if required. G Using the Hex Key and the capscrews, secure the clamps to the vehicle. G Do not tighten at this stage G Ensure spring washer is between clamp and the head of the screw. 7

G Place crossbar foot over clamp.

G Ensure back edge of foot sits flush with the back edge of vehicle roof rail. G Slide clamp through opening in leg. G Using the Hex Key and the capscrews, secure the clamps to the vehicle. G Ensure spring washer is between clamp and the head of the screw. 8

G Thread the coach bolt through the clamp

and the leg. G Tighten the red plastic knob. G Ensure the red plastic knob is in the position shown when fully tightened. G Do not over tighten. G Repeat for all four positions. G Use keys to fit and lock covers G Check crossbar is securely attached to the vehicle. 9

Prorack K682 CAUTION: Recheck all fasteners immediately after

a load is applied to the crossbars. Regularly check screws are tight. 10

G Clean the car roof and surfaces of the

product that will be in contact with the car roof. G Follow the fitting instructions for fitting the product to your vehicle. Make sure all steps are carried out in order. G Set crossbars a minimum distance of 700mm (27 1/2") apart where no other distance is specified in the fitting instructions. This is especially important when carrying long loads. G Check unit is securely attached

G Check and replace worn out or defective

parts. G Keep the product clean and maintained. G Never drive into a car wash with the roof rack system fitted. G Lubricate locks and adjusting screws at regular intervals. G Remove the products from the vehicle when not in use. Make sure all loose parts are stored safely. G Yakima Australia Pty Ltd 17 Hinkler Court Brendale QLD 4500 AUSTRALIA www.whispbar.com www.whispbar.com.au www.whispbar.co

Colorado 7, 5dr SUV 13-+ (NZ)

100mm 910mm - 865mm 845mm - 3 15/16ths" 35 13/16ths" - 34 1/16ths" 33 1/4ths" - Colorado 7, 5dr SUV 13-+ (AU) 100mm 910mm - 865mm 845mm - 3 15/16ths" 35 13/16ths" - 34 1/16ths" 33 1/4ths" - Trailblazer, 5dr SUV 13-+ (ZA) 100mm 910mm - 865mm 845mm - 3 15/16ths" 35 13/16ths" - 34 1/16ths" 33 1/4ths" - 13

WARRANTY & DISCLAIMER

Yakima Australia Pty Ltd ABN 58 154 440 221 17 Hinkler Court, Brendale QLD 4500 Tel: 0800 4776 722 (NZ) or 1800 143 548 (AU) Email: [email protected] or [email protected] Where the product is supplied to the customer for other than business purposes within the meaning of section 43 of the New Zealand Consumer Guarantees Act 1993, the provisions of that Act shall apply. It is important that anyone who fits

Alternately, you can write to Yakima at 17 Hinkler Court, Brendale QLD Australia 4500 in order to make a claim under your

warranty. Upon contacting Yakima directly, you should explain as fully as possible the defect. A Yakima representative will provide you with appropriate instructions for returning the product together with a copy of the original purchase invoice or receipt to Yakima. The costs and expenses associated with making a claim under your

Prorack Automobile Accessories Owners Instructions: