Prorack K769 Fitting Instructions Manual
Text of Prorack K769 Fitting Instructions Manual
Fitting Instructions for Basic Carrier
x 2
x 2
x 4
x 1
x 1
x 1
x 1
x 4
Revision No: 4D
1
MAX kgs (lbs)
W/P
WHD
Mercedes
E-Class W212 GR, 4dr Sedan 09-Aug 16
ZA
75 kgs (165 lbs)
75 kgs (165 lbs)
E-Class W212 GR, 4dr Sedan 09-May 16
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
E-Class W212 GR, 4dr Sedan 09-May 16
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
2
E-Class W212 GR, 4dr Sedan 09-Aug 16 (ZA)
-380mm
380mm
-
930mm
880mm
-
-14 -15/16ths"
14 15/16ths"
-
36 5/8ths"
34 5/8ths"
-
E-Class W212 GR, 4dr Sedan 09-May 16 (NZ)
-380mm
380mm
-
930mm
880mm
-
-14 -15/16ths"
14 15/16ths"
-
36 5/8ths"
34 5/8ths"
-
E-Class W212 GR, 4dr Sedan 09-May 16 (AU)
-380mm
380mm
-
930mm
880mm
-
-14 -15/16ths"
14 15/16ths"
-
36 5/8ths"
34 5/8ths"
-
3
Prorack K769 First Time Installation
G Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
G This kit fits type A, B, C and D.
G These instructions show type A crossbar
fitted. They also apply to type B, C and D.
G Use keys to remove covers.
4
G Use hex screwdriver to reverse adjusting
screw 10 turns.
G Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
G Ensure each end of the crossbar is
adjusted equally.
G Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
G Please check the front of this manual for
information relating specifically to your
vehicle.
5
G Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
G Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
G Select plastic internal block (from fitting kit)
and insert into foot.
G Repeat for all legs.
6
Prorack K769 G Open or remove fixed-point covers.
G Select grubscrews and screw into the
vehicle's fixed points.
G Do not over tighten.
G Note: Use longer [85mm (3 3/8")]
grubscrew at the front and shorter [75mm
(3")] at the rear fixed points.
G Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
7
G Letters refer to the pad part numbers and
position.
G Pad Part Number:
A = 231A
B = 232A
C = 235A
D = 236A
G Ensure the fixed-point covers sit vertically
in the recess in the pads.
G Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
8
G Tighten the plastic knob. The side with the
nut showing should be facing up.
G In the fully tightened position, the knobs
should be parallel with the vehicle.
G Repeat for all four positions.
G Check crossbar is securely attached to the
vehicle.
G Use keys to fit and lock covers
9
Prorack K769 CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
G Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
G Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
G Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
G Check unit is securely attached
G Check and replace worn out or defective
parts.
G Keep the product clean and maintained.
G Never drive into a car wash with the roof
rack system fitted.
G Lubricate locks and adjusting screws at
regular intervals.
G Remove the products from the vehicle
when not in use. Make sure all loose parts
are stored safely.
G Yakima Australia Pty Ltd
17 Hinkler Court
Brendale QLD 4500
AUSTRALIA
www.whispbar.com
www.whispbar.com.au
www.whispbar.co
WARRANTY & DISCLAIMER
Yakima Australia Pty Ltd ABN 58 154 440 221
17 Hinkler Court, Brendale QLD 4500
Tel: 0800 4776 722 (NZ) or 1800 143 548 (AU)
Email: [email protected] or [email protected]
Where the product is supplied to the customer for other than business purposes within the meaning of section 43 of the New
Zealand Consumer Guarantees Act 1993, the provisions of that Act shall apply. It is important that anyone who fits
Alternately, you can write to Yakima at 17 Hinkler Court, Brendale QLD Australia 4500 in order to make a claim under your
warranty.
Upon contacting Yakima directly, you should explain as fully as possible the defect. A Yakima representative will provide you
with appropriate instructions for returning the product together with a copy of the original purchase invoice or receipt to
Yakima.
The costs and expenses associated with making a claim under your