Progress Lighting Airpro P250073 Installation Manual

Date Purchased Store Purchased UL Model No. Serial No. Vendor No. UPC 111017 P250073 Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to be free from defects in materials or workmanship for a period of 1 year from the date of pu ...

Installing Your Fan Wiring the Fan Preparing the Remote Control Operating Your Fan Care of Your Fan Troubleshooting Specifications Table of Contents 1 2 3 8 10 11 12 12 13 ...

turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. CAUTION: To reduce the risk of personal injury, use only the screws provided with the electrical box. 4. The outlet box and ...

(16 screws) b. Flywheel attachment hardware (6 screws) c. Decorative ring attachment hardware (6 screws) d. Upper housing attachment hardware (7 screws) e. Electrical hardware and Balancing kit (1 plastic wire connector, blade balancing kit) 7. Upper housing 8. Flywheel 9. Decorative ring 10. Finial 11. Transmitter and Receiver 12. Lead Wire 1. Mounting Bracket (inside canopy) 2. 6” Ball/Downrod Assembly (hanger pi ...

Tools Required Phillips screw driver or straight slotted screw driver, adjustable wrench, step ladder, and wire cutters. Mounting Options If there isn’t an existing electrical box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the electrical box directly to the building structure. Use appropriate fasteners and building materials. The electrical box and its suppo ...

1. Attach the blades to the flywheel by aligning the notches on the blades with alignment post on the flywheel and put the blade on to the flywheel. Secure with screws but do not tighten. (Figure 5) 2. Repeat these steps for remaining blades. 3. Put the flywheel upside as shown (Fig. 6). Attach the finial to the bottom of the flywheel aligning the screw holes of the finial with the holes of the blade, secure with screws and t ...

Ring 1. Attach the decorative ring through the bottom of the flywheel by aligning the holes on the decorative ring with the holes on the tab and install the screws. (Figure 7) 2. Put the fan motor assembly inside the flywheel, engage the fan motor assembly with tabs onto the flywheel by turning clockwise till the screw holes on the fan motor assembly align with the holes on the tab of flywheel.(Fi ...

on the collar on the top of the motor housing. 6. Align the holes at the bottom of the downrod with the holes in the collar on top of the motor housing. (Figure 13 ) 7. Carefully insert the hanger pin through the holes in the collar and downrod. Be careful not to jam the hanger pin against the wiring inside the downrod. Insert the locking pin through the hole near the end of the bolt until it snaps into its l ...

the Electrical Box 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 14. 2. Install the ceiling mounting bracket on the electrical box by using the mounting screws provided with the electrical box. Note that the flat side of the mounting bracket is toward the electrical box. (Figure 14) 3. Tighten the two screws on the electrical box securely. 4. Carefully ...

Wiring the Fan to the Receiver 1. If using the 6 in. ball downrod assembly provided, wire the receiver to the fan wires by connecting the molded adaptor plug from this receiver with the molded adaptor of the fan motor assembly together. (Figure 17) 2. If you wish to use longer downrod, you can use the extension lead wire (66 in.) provided by connecting the molded adaptors together. Figure 17 SUPPLY CIRCUIT BLUE Remote Receiver WHITE L N ...

2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the ceiling. Measure this distance as shown in Figure 19. Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. Measurements deviation should be within 1/8 ...

Figure 20 Mounting the remote control holder 1. Position the wall cradle in the desired position and attach it to the wall using the included wall cradle screws. NOTE: Screw wall anchors are included for extra support. The included screws are designed to screw easily into the wall. If you would like a more permanent or secure hold, install the wall anchors prior to attaching the wall cradle to the wall. Figure 21 LEARN CFL 0 D 1 L ...

Figure 23 Figure 24 Figure 22 Remote Control Warm weather - (Forward) A downward air flow creates a cooling effect as shown in Figure 23. This allows you to set your air conditioner on a higher setting without affecting your comfort. Cool weather - (Reverse) An upward air flow moves warm air off the ceiling are as shown in Figure 24. This allows you to set your heating unit on a lower setting without affecting your comfort. Timer: Wh ...

Care of Your Fan Here are some suggestions to help you maintain your fan. 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) 2. Clean your fan periodically to help maintain its new appearance over the years. Do not use water when clean ...

CFM/WATT NET WEIGHT GROSS WEIGHT CUBE FEET 60” Low 120 3 2576 858.7 22.49 Lbs 27.34 Lbs 3.14 High 37.79 6966 184.3 ©2017 Progress Lighting, Inc. 701 Millennium Blvd., Greenville, SC 29607 All Rights Reserved This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part ...