YUNEEC GB200 Quick Start Manual

TABLE OF CONTENTS 1 Table of Contents 2 .................... Warnings and Important Notes 4 Overview 6 How to switch Camera Mounts: CGOl ™ to GoPro3/ 3+ 7 How to switch Camera Mounts: GoPro3/ 3+ • to CGOl ™ 9 Mounting CGOl™ on GB200™ 9 Mounting GoPro• on GB200™ 9 .................... Mounting GB200™ on Blade• 3500X2 13 GB200™ LED Status 14 Spare Parts and compatible products 14 Troubleshooting Guide 16 ................... Limited Warranty Yuneec Exhibit 1037 Page 1

Warning: Do not move, sway or shake the model during the initialization process. Moving, shaking or swaying the model during the initialization process may lead to initialization failure, which will require you to cyde the power off and then back on to repeat the process. Adjusting or modifying the GB200™ in anyway is not recommended. Prior to using the GB200™, read and under- stand the quick start guide and instruction manual completely. Always power on your transmitter first and then power on your model and gimbal. YUN EEC™ GB200™ gimbal is optimized for both the CGOl ™ andGoPro3/3+" cameras. Please mount your camera to the GB200™ without adjusting or modifying the GB200™. Do not modify or add any other component I device (such as filters, lens, plastic case, hood, etc.) to the camera. Also, it~ important to make sure to use the original battery for your chosen camera, or the change in weight and center of gravity of the camera may de- crease performance of GB200™ or even cause internal malfunction. Make sure your model's autopilot system operates in the safest manner when the main power battery is connected. We strongly recommend that you remove all blades/propellers, use a suitable flight battery, and keep a safe distance from children and other people during gimbal setup. Please follow these important steps to mount and connect the GB200™ gimbal on your model, and respect the AMA's National Model Aircraft Safety Code. 2 Yuneec Exhibit 1037 Page 2

modification (including use of non-specified YUNEEC™ parts i.e. motors, flight controllers, motor controllers, blades/propellers, etc) or misuse. Therefore no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. YUNEEC™ assumes no liability for damage(s) or injuries incurred directly or indirectly from the use of this product. YUNEEC™ and GB200™ are trademarks or registered trademarks of Yuneeclnternational Co., Ltd .. This product and manual are copy- rights of YU NEEC™ with all rights reserved. No pa rt of this product or manual shall be reproduced in any form without the prior written consent or authorization from YUNEEC™. Furthermore, no other liability is assumed with respect to the use of the product or information contained herein. YUNEEC™ reserves the right to update manuals and quickstart guides any time. For warranty infor- mation, please visit www.Yuneeccom 3 Yuneec Exhibit 1037 Page 3

Angle Mode allows the'pitch' angle of the camera gimbal to be changed relative to the PWM control stick/knob/slider input. Velocity Mode controls the speed/rate of the'pitch' angle of the camera according to PWM control stick/knob/slider input. For example, the more control input the faster the rate of change will be. 4 Yuneec Exhibit 1037 Page 4

0 (A) Step 1: Rotate the CGOl™ Gtmera mount- as shown in illustration A- until the flat spo t inside the setscrew hole is facing up, and loosen the setscrew using the alien wrench. Step 2: Carefully remove the CGOl™ camera mo unt by sliding it outward away from the gimbal motor and remove the gyro board from the gyro board mount. Step 3: Insert gyro board into the gyro board mount o n the GoPro• Gtmera mount and wrap the gyro board wire harness clockwise one whole turn around the end of the camera mount toward the gimbal motor. 6 Yuneec Exhibit 1037 Page 6

the setscrew hole. Insert and tighten the setscrew to secure the GoPro• mount to the GB200™. HOW TO SWITCH CAMERA MOUNTS: GoPro3/3+0 to CG01'" (8) Step 1: Rotate the GoPro• camera mount- as shown in illustration B - until the flat spot inside the setscrew hole is facing up, and loosen the setscrew using the hex wrench. Step 2: Carefully remove the GoPro" camera mount by sliding it outward away from the gimbal motor and remove the gyro board from the gyro board mount. Step 3: Insert gyro board into the gyro board mount on the CGOl™ camera mount and wrap the gyro board wire harness dockwise one whole turn around the end of the camera mount toward the gimbal motor. Step 4: Spin the gimbal motor shaft until the 'flat spot' is facing the setscrew hole. Insert and tighten the setscrew to secure the CGOl™ mount to the GB200™. 7 Yuneec Exhibit 1037 Page 7

Illustration B: GoPro 3/3+~ mount 8 Yuneec Exhibit 1037 Page 8

1. Remove the 5.8GHz Wi-Fi antenna from the CGOl ™. 2. Install the CGOl™ into theCGOl™ camera mount. 3. Connect the 5.8GHzWi-Fi antenna by pressing it onto the 5.8GHz antenna socket on the CGOl ™ and tum it 90° to secure the antenna to the CGOl ™and camera mount. 4. Install the 3mm mounting screw to secure the CGOl™ to the mount. MOUNTING GOPR0° ON GB200'" (D) 1. Install GoPro3/3+• in the GoPro3/3+• mount 2. use the GoPro3/3+" mounting sleeve to secure the camera to the mount. (see illustration) MOUNTING GB200'" ON BLADE" 350QX (E,F,G and H) 1. Install the GB200™ gimbal mounting plate on the 350QX using the (4) included screws. 2. Slide the GB200™ into place with the arm side toward the back of the model. 3. Connect the Blade• 350 QX2 control cable to the camera pitch control port on the GB200™ and the corresponding port on the Blade• 350QXV2. 4. Place the Blade• 350 QX2 on a flat and stable surface. Switch on the Blade" 350 QX2. Do not move, sway or shake the model during the automatic calibration process. After the automatic calibration is complete, your GB200™ is ready to use. 9 Yuneec Exhibit 1037 Page 9

camera Illustration 0: Mounting GoPro0 camera Yuneec Exhibit 1037 Page 10

Illustration F: Sliding

Blade• 350 0X2 control caUe on the Blade• 350 0X2 Illustration H: Powering 12 Yuneec Exhibit 1037 Page 12

your desired pitch axis position within 5 seconds after the gimbal initializes. GB200'" LED STATUS ANGLE CONTROL MODE: LED COLOR RED 1. PWM Control Input (port 2): the red LED will flash once and become solid. 2. Spektrum• Satellite Receiver inserted (port8/9): the red LED w ill flash twice and become sol id. ANGULAR VELOCITY MODE: LED COLOR BLUE 1. PWM Control Input (port 2): the blue LED will flash once and become solid. 2. Satellite receiver inserted (port8/9): the blue LED will flash twice and become solid. 13 Yuneec Exhibit 1037 Page 13

BLH7901 .................. Main Control Board w/ RX: 350 QX2 BLH7902 .................. White Battery Cover: 350 QX2 BLH7903 .................. Battery Frame: 350 QX2 BLH7904 .................. Gimbal Arms: GB200™ BLH7905 .................. Gimbal Motors: GB200™ BLH7906 .................. Gimbal Mount: GB200™ BLH7907 ..... ............. Gimbal Control Board: GB200™ BLH7908 .................. Camera mount CGOl™: GB200™ BLH7909 .................. Camera mount Go ~o Hero 3•: GB200™ BLH791 0 .................. GB200™ Brushless Gimbal TROUBLESHOOTING GU IDE WHAT WHY SOLUTION The gimbal ke€ps Carner a may not be Check and make sure vil:xating after mounted securely to camera is mounted initializing. the camera mount. completely and secu- rely in the camera mount. Camera needs to be pressed into the Camera mount completely; otherwise, the cmter ofgr

Gmba1 control If using GB200'"with power on. harness may not be Blade• 350 OX2, be sure connected into the to connect the control correct port harness to the earner a !'.itch control port . If using with any other model, be sure to connect PWM input to port the universal PWM input por t and mode control port Gimbal does not Gmba1 may not have Gieck gimbal control respond to control positive connection harness/satellite r inputs and LEDs via control harness or eceiver for a solid are glowing so!id satellite receiver. connection. Try RED and BLUE. disconnecting and reconnecting the control ha-ness/satellite receVff zndcycling !he power on/off. Red LED on gi mbal The gyro board Check the connection flashes slowly and harness may have between the gyro gimbalis disconnected from board and the GB200'" inoperable. the GB200 '~ control control board. board. 15 Yuneec Exhibit 1037 Page 15

of purchase, the pro du ct wil I be free from defects in materials and workmanship under normal use. In the event of a defect please contactYUNEEC customer Support (www.Yuneeccom)for assist- ance. YUNEEC's sole obligation under this warranty will be, at its option, to repair or replace the product This warranty does not apply to products damaged by misuse, accident or normal wear and tear and water damage. All implied warranties of merchant- ability or fitness for a particular purpose are limited to the duration of this warranty. YUNEEC'" disdaims all other expressed or implied warranties or conditions. to the extent not prohibited by law, in no event will YUNEEC'" be I iable for any loss of revenue or profit or for any special, indirect, consequential, incidental or punitive damages, however caused, arising out of or related to the use of or inability to use the product, even ifYUNEEC'"has been advised of the possibility of such damages. In no event will Yu neec'" liability exceed the amount paid by you for the product Some jurisdictions do not allow limitations on how long an implied warranty lasts, or the exdusion or limitation of ind dental or consequential dama- ges, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary by jurisdiction. BLRIJE. Copyright 2014 YLl'lee< Int ernational Co, ltd . I Horizon Hobby, LLC 16 Yuneec Exhibit 1037 Page 16