Truma AquaGo basic Frequently Asked Questions Manual

Truma AquaGo How Does the Truma AquaGo Work? The Truma AquaGo instant water heater is connected between the vehicle's fresh water supply and its hot water system. When the appliance is switched on, the burner starts automatically as soon as the hot water faucet is opened and the flow of the water is greater than approximately 0.4 gallons per minute (1.5 l/min). The stepless burner control adjusts heater output based on flow and i ...

Please follow these instructions step by step 1. Power to the unit must be on from the main panel 2. The outside switch on the AquaGo needs to be in the “ON” position either up or down. 3. Turn rotary dial on inside switch to “ECO” or “Comfort” mode (these are the top 2 positions on the switch) 4. Wait until you hear the circulation pump cycle on and off – You may need to “wake up” the switch ...

Winterizing your AquaGo is easy with the "Easy Drain Lever".  Drain all the water from the appliance  Release the yellow "Easy Drain Lever" on the front of your AquaGo  Remove the filter and let the water drain  Store your filter in a safe place for the winter - DO NOT put it back in the AquaGo Watch Billy demonstrate this simple process in the attached video. How to Operate My AquaGo Control Panel Learn how to:  S ...

Turn the switch slowly to the on position then to the off position. You may have to do this multiple times in order to get the light to come on indicating the system is ready for operation. How to reset an AquaGo accidentally set to clean mode Follow these instructions step by step. 1. Be sure the exterior main switch on the AquaGo unit is in the ON position, either the up or ...

1 Control panel 2 Gas connection 3 Solenoid valve 4 Combined combustion air/exhaust cowl 5 Combustion air fan 6 Gas burner 7 Ignition electrode 8 Combustion chamber 9 Flame tube with baffle 10 Combustion air fan 11 Heat exchanger 12 Electric heating elements ...

14 Stainless steel water container,10 litres 15 Hot water connection pipe 16 Cold water connection pipe 17 Room temperature sensor 18 HDF thermal jacket The furnace is switched on and the required temperature for heating and warm water is set on the Truma Combi LCD control panel (1). The gas supply to the furnace is controlled by the solenoid valve (3). The necessary combustion air flows through the outer pipe of the combined inlet ...

1. Place a vessel that's at least 2.64 gallons (10 liters) underneath the drainage outlet of the drain valve. 2. Use the main switch or pump switch to turn off the power to the water-pump 3. Turn off or disconnect the city water connection if present 4. open all water release points, e.g. cold and hot water faucets, showers, toilets 5. flip yellow handle to be in line wi ...

Air intake is obstructed  Clear air intake  check warm air outlets for blockage or crushed ducting Combi has no error code but will not stay lit Check to make sure the tank has not frozen becoming swollen and restricting the air flow into ducting. This could cause the unit to overheat and cycle off. What to check if your Combi will not operate on gas mode 1. Has the Combi previously worked on LP? 2. is the gas tu ...

10. does the Combi operate properly in 110V mode? 11. Has the high limit reset been tripped? 1. If so, run cold water through the Combi for a few minutes and reset if tripped. What to check if your Combi will not operate on 110V power 1. Is there 110V power available to the vehicle? 2. does the Combi operate in gas only mode? 3. Is the 12V master switch on? 4. Is the high limit reset tripped? 1. If s ...

To measure, place the Truma LevelCheck against the wall of the LPG tank horizontally at a 90° angle. The fill level is determined using an ultrasound signal. If there is LPG at the measured area, the signal is echoed by the opposite wall of the tank. This measurement is indicated by a green LED and a high-pitched "beep". If there is no LP at the measured area, the signal is not echoed back. This is indi ...

red. Important In order to obtain a reliable measurement, the measuring head must be cleaned regularly with a wet cloth (do not use any cleaning agents). A soiled measuring head can result in inaccurate measurements. Dust particles often stick to tanks, particul ...

 A longer measuring time between 3 and 10 seconds is an indication of an unclear signal, which will result in a red indicator (erroneous measurement). Additional note: Measurements taken in the lower area of full gas cylinders often fail. This is because of the restricted reflection of the echo from the di ...

The free Truma App provides practical tools to help you when you are travelling:  In combination with the Truma iNet Box, control iNet-capable Truma appliances remotely via your smartphone or tablet.  With Truma sun alignment, you see immediately where and when the sun is at its highest and at what time the sun rises and sets.  Vehicle levelling helps you align the vehicle horizontally.  With the App you ...

es, the Truma App also runs on tablets with iOS and Android. Download the Truma App now from the App Store or Google Play. What is the Calibration Function in the Truma App Good for while Leveling? The sensors in smartphones and tablets can become unaligned over time. The calibration in the Truma App realigns the sensors. You need a horizontal surface for this. Why do I have to Calibrate my Smartphone before I can us ...

If you use the Truma App without iNet Box, all functions, such as the practical camping tools, are available offline. The instructions are downloaded once when you have a wireless connection and are stored on the mobile device. If you use the Truma App in combination with the Truma iNet Box to control your appliances, you can use the Truma App via Bluetooth when it is within range at no additional costs. Additional cost ...

We are working hard to develop an integrated digital solution to support connected systems in the future and will provide additional information once available. ...