Yamaha CD-C600BL Owner's Manual

i En 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The ...

ii En FCC INFORMATION (for US customers) 1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3 NOTE: This prod ...

iii En 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances. Top : 2.5 cm (1 inch) Rear: 2.5 cm (1 inch) Sides: 2.5 cm (1 inch) 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. 4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate t ...

Front panel................................................................. 2 Rear panel connections.............................................. 4 Remote control........................................................... 5 LOADING AND PLAYING DISCS ..................... 8 Program playback .................................. 8 PLAYXCHANGE ..................................................... 8 PLAYING BACK iPod/USB DEVICE................. 9 Connecting iPod/USB devices................................... 9 Playing back iPod .. ...

Loads a disc. 2 (Open/Close) Opens or closes the disc tray. For loading and unloading discs, see page 8. 3 (Power) Press inward to the ON position to turn on the power. y • The power indicator above lights up when this unit is turned on. • You can turn this unit to a standby status with STNDBY/ON on the remote control. • This unit is equipped with the Auto standby function. By turning on the function, this unit turns to the standby mode automatically when disc playback is stopped for 30 minutes. For details, see page 13. 4 Power indicator Lights up as follows: ON: Bright Standby mode: Dark OFF: Off 5 DISC (1-5) Se ...

E Disc select indicator The numbers corresponding to the trays containing discs light up. The enclosed number indicates the currently selected disc. The number corresponding to an empty tray may light up before the tray is selected. When the disc tray is closed after loading/ replacing discs, this unit searches discs starting from tray 1. During the search, the tray numbers corresponding to empty trays go off. When a disc is detected, the searching finishes there and the remaining trays are left unsearched. F Playback status Indicator Lights up when this unit is in the play or pause mode. G Source type i ...

Before making any connection, switch OFF the power to the unit, the amplifier and any other component. ■ VOLTAGE SELECTOR (Asia and General models only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local voltage BEFORE plugging the power cable into the AC wall outlet. Improper setting of the VOLTAGE SELECTOR may cause damage to this unit and create a potential fire hazard. Rotate the VOLTAGE SELECTOR clockwise or counterclockwise to the correct position using a straight slot screwdriver. Voltages are as follows: ...............AC 110/120/220/230-240 V, 50/60 Hz Rear panel connections CAUTION Opt ...

1 Infrared signal transmitter Sends infrared signals to this unit. 2 STANDBY/ON Turns this unit on or to the standby mode while (Power) on the front panel is pressed inward to the ON position. You can operate this unit only when the (Power) on the front panel is pressed inward to the ON position. 3 CD/USB Switches between CD mode and iPod/USB mode (see page 9). y This setting is retained even if you turn off this unit. 4 PROGRAM Turns on or off the program playback mode. See “Program playback” on page 8. 5 DIMMER Each time you press DIMMER, the brightness level changes by 4 levels. y This setting is ...

E REPEAT Repeats playback of a single track or all tracks. Each time you press REPEAT during playback, the repeat playback mode changes as follows: • REP TRACK (single repeat playback): A single track is played back repeatedly. • REP ALL (all repeat playback): All tracks (the entire disc) are played back repeatedly. • REP FOLDER (folder repeat playback): All files (the entire folder) are played back repeatedly. y Repeat play also works with program play and random-sequence play. F DISPLAY Switches the time display. Each time you press DISPLAY during playback, the time display changes as follows: G A/B Repeats playback ...

■ Installing batteries in the remote control 1 Press the part and slide the battery compartment cover off. 2 Insert the two supplied batteries (AA, R6, UM-3) according to the polarity markings (+ and –) on the inside of the battery compartment. 3 Slide the cover back until it snaps into place. ■ Using the remote control The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the front panel of this unit during operation. ■ Notes on batteries • Change all of the batteries if you notice that the operation range of the r ...

1 Press OPEN/CLOSE to open the disc tray and load discs. Use the disc guides to align the discs correctly in the tray. To play back an 8 cm (3 inch) CD, place it in the inner recessed area of the disc tray. Do not put a normal (12 cm (5 inch)) CD on top of an 8 cm CD. 2 Press OPEN/CLOSE to close the disc tray. 3 Press MODE to select a desired disc play mode (1DISC or 5DISC) confirming it on the display. 1DISC: Only the selected disc is played back. 5DISC: All discs on the tray are played back in sequence. 4 Press (Play) to start playback from the first track or file of disc 1. 5 (If necessar ...

• Turn off your iPod. • Do not use a USB hub. 1 Press CD/USB to select the iPod/USB mode. The iPod/USB indicator on the front panel lights up in orange, then changes to green when playback is ready. 2 Start playback. Operate your iPod to start playback, select a track, pause, and stop playback. y You can also use the following buttons: p (Playback), e (Pause), s (Stop), b (Skip backward), a (Skip forward), w (Search backward), and f (Search forward) on this unit or Remote Control. iPod may not function properly with this u ...

Stop playback, and then disconnect your iPod or USB device. It is recommended that you press CD/USB to switch to the CD mode, confirm that the CD/USB indicator goes off, and then disconnect your iPod/USB device. Do not disconnect your iPod or USB device while playing back from the connected device, or while “USB READING” appears in the front panel display. ■ Supported iPod models • iPod classic (including 120GB model) • iPod nano (2nd, 3rd and 4th generations) • iPod touch (1st and 2nd generations) (as of April 2009) • iPod is licensed on the condition that individuals perform privately duplication and p ...

device and Data Disc) MP3 * Variable bitrate is also supported. WMA • Version 8 • Version 9 (Standard and variable bitrates are supported. Professional and Lossless are not supported.) * Variable bitrate is also supported. • Playback for Data Disc starts in alphanumeric order. • Playback for USB starts in order by date and time of creation. • Copyright-protected WMA (DRM) files cannot be played back by this unit. • The disc must be ISO 9660 compatible. • Elapsed time may not be displayed correctly while playing back variable bitrate contents. � ...

■ Handling compact discs • Always handle with care so that the playing surface is not scratched. Do not warp discs. • To keep clean the playing surface, wipe with a clean, dry cloth. Do not use any type of disc cleaner, spray, or any other chemical-based liquid. • Do not wipe with a circular motion; wipe straight outward from the center. • Use a soft-tipped pen when writing on the label side of the disc. • When a disc is not being used, remove it from this unit and store in an appropriate case. • Do not expose discs to direct sunlight, high temperature or high humidity for a long time. ...

modes, which may be useful for special purposes at stores or offices. The special mode functions are incompatible with iPod. Play mode memory Retains the current playback mode (REPEAT and RANDOM) after turning off the power, saving the time of setting the playback mode again each time you turn on the power. The track number is also retained so playback starts with the same track automatically when you turn on the power again. The RESUM indicator in the front panel display lights up when enabled. Ready mode Pauses playback after each track, allowing you to start t ...

simple measures suggested. If it cannot be corrected, or if the problem is not listed in the Problems column, disconnect the power cable and contact your authorized Yamaha dealer or service center for help. TROUBLESHOOTING Problems Possible Causes Solutions Refer to page This unit fails to turn on. The power cable is not connected to the AC IN inlet on the rear panel or not plugged in the wall outlet. Connect the power cable firmly. 4 This unit suddenly turns off. Auto standby mode is set to on. Set the auto standby mode to o ...

• Harmonic distortion + noise (1 kHz).........................0.003 % or less • S/N ratio.................................................................... 105 dB or more • Dynamic range............................................................ 96 dB or more • Output voltage (1 kHz, 0 dB) ...........................................2.0 ± 0.3 V Laser Diode Properties • Material..................................................................................GaAlAs • Wavelength........... ...