Perlesmith PSLT6 Instruction Manual

Text of the manual

TV WAll Mount Instruction Manual

Thank you for choosing this PERLESMITH product! At PERLESMITH we strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com/ pages/reviews if you are satisfied. Should you have any issues, please don't hesitate to conta

DO NOT exceed the maximum weight indicated.

This mounting system is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage and or injury. WARNING If your TV weighs more, this mount is NOT compatib

Tools Needed (Not lncluded)

Supplied Parts and Hardware Supplied Parts and Hardware for Step 1 Warning: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, plea

Note: The spacers are shown in accordance with the actual size.

[06] Spacers [If necessary] [07] TV Bolts Supplied Parts and Hardware for Step 2 Ø8mm Washer x4 B Lag Screw ST8X65mm x4 A Supplied Parts and Hardware for Step 3 [M-A1] [M-A2] M6 x 15mm x4 M6 x 30mm x4 [M-B1] M8 x 15mm x4 [M-B2] M8 x 50mm x4 Note: The bolts are shown in accordance with the

Step 1 Secure the TV Brackets to TV

Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns. -Too short will not hold the TV. -Too long will damage the TV. Please Note: The provided TV bolts meet most of today's TVs design. However, some TVs require special bolts w

CAUTION: Ensure the TV

brackets [01] and [02] are EQUALLY CENTERED on your TV AND securely fastened in place. Option A (For Flat Back TV) 07 M-A1/M-B1 05 M-D 07 M-A2/M-B2 05 M-D 06 M-C/M-E Option B (For Round Back TV) 01 02 01 02 UP 01 02 Alternate Spacer Setups Please note: The bolt hole locations on your TV may vary in accordance of the manufacturers desig

Step 2 Assemble Wall Plate

DO NOT overtighten. Tighten only until snug. Option D For cable interference or inset holes, use spacers [M-C] and [M-E] to create extra space between the TV and TV brackets 01/02 M-C/M-E 06 M-A2/ M-B2 07 05 M-D Spacers may be necessary for 2 holes ONLY. Option C (For TV with A “Bump”) 01 02 07 M-A2/M-B2 05 M-D 06 M-C/M-E 07 M-

Position the wall plate [03] at

your desired height and line up the holes with your stud center line. Level the wall plate and mark the holes. Use a stud finder(not included) to locate wood studs or use an awl (not included) to verify the edges. Mark the edge and center locations. Step 3 Attach Wall Plate to Wall Step

1/2 in.(13 mm)

Socket Wrench (Not included) Install the wall plate [03] using lag screws [A]. Tighten the lag screws [A] only until the washers [B] are pulled firmly against the wall plate [03]. Drill 4 pilot holes using a 7/32 in. (ø5.5 mm) diameter drill bit. Make sure the depth is not less than 2 9/16 in. (65 mm). 7/32 in. (ø5.5 mm) 2 9/16 in. (65

1/2 in.(13 mm)

Socket Wrench (Not included) 3B-1 Position the wall wall plate [03] at your desired height, level the wall plate and mark the pilot hole locations. 3B-2 3/8 in.(ø10mm) 2 3/4 in.(70mm) Drill 4 pilot holes using a 3/8 in. (10mm) diameter drill bit. Make sure the depth is not less than 2 3/4 in.(70mm). Never drill into the mortar betwee

Other TV Mount Manuals