Sauder 415543 Manual 

Text of Sauder 415543 Manual 

PLEASE CONTACT US

BEFORE RETURNING YOUR UNIT TO THE STORE 1-800-523-3987 www.sauder.com Made in the USA Archbold, OH NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Lot #: 363404 07 / 11 / 14 Date Purchased: ____________________ English .................... Page 1-15 Français ...............Pages 16-18 Espanol .............Páginas 19-21 415543 Night Stand

ADULT ASSEMBLY REQUIRED

ASSEMBLY TOOLS REQUIRED Hammer No. 2 Phillips Screwdriver Tip Shown Actual Size TABLE OF CONTENTS Part Identifi cation .......................3 Hardware Identifi cation .............4 Assembly Steps .................... 5-15 Français .............................. 16-18 Espanol ............................... 19-21 Safety .......................................22 Warranty ...................................23 Page 2 www.sauder.co

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked

letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help identify similar parts. FF RIGHT END 1 GG LEFT END 1 HH TOP 1 II BOTTOM 1 JJ SKIRT 1 KK BACK 1 NN DRAWER FRONT 1 D217 DRAWER SIDE 2 D218 DRAWER BACK 1 D613 DRAWER BOTTOM 1 Page 3 www.sauder.com/services 415543 FF GG HH II JJ KK NN D217 D217 D218 D61

APPLIQUE CARD - 1

35P HARDWARE IDENTIFICATION Screws are shown actual size. You may receive extra hardware with your unit. Page 4 www.sauder.com/services 415543 BLACK 9/16" LARGE HEAD SCREW - 8 1S ANGLE BRACKET - 3 5G BLACK 1-7/8" FLAT HEAD SCREW - 4 2S CAM DOWEL - 4 2F HIDDEN CAM - 4 1F BLACK 1/2" FLAT HEAD SCREW - 4 43S BLACK 1-1/2” PAN HEAD SCREW - 4 49S NAIL - 8 1N PULL - 1 45K 53S SILVER 3/4” MACHINE SCREW - 2 52S SILVER 3/4" PAN HEAD SCREW - 4 S

Look for this icon. It means a video

assembly tip is available at: www.sauder.com/services/tips 1 S t e p Page 5 www.sauder.com/services 415543 Assemble your unit on a carpeted fl oor or on the empty carton to avoid scratching your unit or the fl oor. Push four HIDDEN CAMS (1F) into the ENDS (FF and GG). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. (4 used) Arrow 1F 2F Insert the metal

NOTE: Before beginning this step, separate the SLIDES from the SLIDE SETS (MM) and the DRAWER PINS at the end of the

SLIDES using a SCISSORS. Save the DRAWER PINS. You will use them in Step 10. Fasten the SLIDES (MM) to the ENDS (FF and GG). Use four SILVER 3/4" PAN HEAD SCREWS (52S) through the first and last holes in the SLIDES. NOTE: The SLIDES are marked "RIGHT" and "LEFT" for easy identification. T

Fasten three ANGLE BRACKETS (5G) to the BOTTOM (II) and SKIRT (JJ). Use three BLACK 9/16" LARGE HEAD

SCREWS (1S). NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the BOTTOM (II) and SKIRT (JJ). BLACK 9/16" LARGE HEAD SCREW (3 used in this step) 1S 5G 5G II JJ Surface with holes

Fasten the TOP (HH) to the ENDS (FF and GG). Tighten four HIDDEN CAMS.

FF GG HH Finished edge Caution Risk of damage or injury. Hidden Cams must be completely tightened. Hidden Cams that are not completely tightened may loosen, and parts may separate. To completely tighten: Start Tighten Arrow Arrow Maximum 210 degrees Minimum 190 degrees Finished edge Surface without HIDDEN CAMS Surface with HIDDEN CAMS

Fasten the BOTTOM (II) to the ENDS (FF and GG). Use four BLACK 1-7/8"FLAT HEAD SCREWS (2S).

Fasten the SKIRT (JJ) to the BOTTOM (II) and ENDS (FF and GG). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). FF GG II JJ BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) 2S BLACK 9/16" LARGE HEAD SCREW (3 used in this step) 1S Surface with ANGLE BRACKET Edge with ANGLE BRACKET

Sauder Indoor Furnishing Owners Instructions: