Toro 38620 Operator's Manual

8111 Lyndale Ave., Bloomington, MN 55420, USA Printed in the USA All Rights Reserved Original Instructions (EN) Register your product at www.Toro.com 826LE Power Max Snowthrower Model No. 38620—Serial No. 240000001 and Up Form No. 3329-770 Rev A Operator’s Manual Introduction Read this manual carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product. Whenever you need serv ...

Training • Read the operator’s manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly. • Never allow children to operate the snowthrower. Never allow adults to operate the snowthrower without proper instruction. • Keep the area of operation clear of all persons (particularly small children) and pets. • Exercise caution to avoid slipping or falling, especially when operating the snowthrower in reverse. Preparation • Thoroughly inspect the area where you will use the snowthrower. Remove all doormats, sleds, boards, wires, and ...

• Never operate the snowthrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handle. Walk; never run. Maintenance and Storage • Check all fasteners at frequent intervals for proper tightness to be sure that the equipment is in safe working condition. • Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water and space heaters and clothes dryers. Allow the engine to cool before storing in any enclosure. • Always refer to this operator’s manual for important details if the snowthrower is to be stored for an extende ...

Read and understand the contents of this manual before operating the snowthrower. Become familiar with all controls and know how to stop the engine quickly. Before Operating Operator's Position 472 Caution: Improper use may result in loss of fingers, hands, or feet. impeller close to the of the opening. The lowspeed auger has a moving pinch point close to the opening. There is a highspeed m-6936 Safety/Instruction Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 53-7670 1. Cutting/dismemberment of foot, auger ...

106-4521 106-4587 107-3825 1. Fast 2. Forward speeds 3. Slow 4. Reverse speeds Tecumseh Part No. 36501 1. Primer Tecumseh Part No. 35077 1. Key ignition 2. Engage to start the engine 3. Disengage to stop the engine 4. Fast 5. Increasing scale 6. Slow 7. Stop the engine Tecumseh Part No. 37119 ...

Product Overview 1 2 3 4 5 6 8 12 10 11 9 m-6936 7 1. Auger/impeller lever 2. Speed selector lever 3. Quick Stick discharge chute control 4. Traction lever 5. Fuel tank 6. Engine oil fill tube/ dipstick 7. Chute deflector 8. Discharge chute 9. Fuel shutoff valve 10. Skid (2) 11. Auger 12. Scraper 1 6 3 4 5 2 1. Ignition switch 2. Choke 3. Throttle 4. Primer 5. Electric starter 6. Recoil starter Setup Installing the Upper Handle Assembly 1. Lift and rotate the upper handle assembly and position it over the lower handle. Note: Ensure that the 2 cables attached to the Quick Stick are routed inside the upper handle legs and that the 2 le ...

Installing the Traction Control Linkage 1. Remove the hairpin cotter and washer from the the lower end of the speed control rod (A) and insert the lower end of the rod into the lower link arm (B) so that the bent end of the speed control rod faces rearward. m-6899 B A 2. Secure the lower end of the speed control rod with the washer and hairpin cotter that you previously removed. 3. Remove the hairpin cotter and the outer washer (of 3 washers) from the trunnion (A) on the upper end of the speed control rod. m-6898 C B A D Note: To make installation easier, leave the wave washer (B) and the flat washer (C) on the trunnion. 4. Shift the s ...

5. Hold the long chute control rod in this orientation (you must move it back to insert it into the gear) and insert the front end of the rod into the opening in the back of the chute gear cover until it slides into the chute gear. 6. Align the holes in the nested ends of the rods and insert 2 carriage bolts through the short rod from the left side of the snowthrower (as viewed from the operating position). 7. The 2 carriage bolts (in the loose parts bag) will go through the holes in the short rod and then through the holes in the long chute control rod. 8. Insert the cable clip (A) that supports the deflector cable (B) onto the forwar ...

Filling the Fuel Tank Danger Gasoline is extremely flammable and explosive. A fire or explosion from gasoline can burn you and others.
To prevent a static charge from igniting the gasoline, place the container and/or snowthrower on the ground before filling, not in a vehicle or on an object.
Fill the tank outdoors when the engine is cold. Wipe up spills.
Do not handle gasoline when smoking or around an open flame or sparks.
Store gasoline in an approved fuel container, out of the reach of children. Fill the fuel tank with fresh unleaded regular gasoline from a major name-brand service station. Important: To reduce starting prob ...

6. Firmly push in the primer 3 times with your thumb, holding the primer in for a second before releasing it each time. Note: Take your glove off when you push in the primer so that air cannot escape from the primer hole. Note: Priming excessively may flood the engine and prevent it from starting. 7. Start the snowthrower using the recoil starter or the electric starter. m-4516 or Important: To prevent damaging the electric starter, run it no more than 10 times at intervals of 5 seconds on, then 5 seconds off. If the engine does not start after this series of attempts, allow the starter to cool for at least 40 minutes before trying to ...

3. Check to ensure that the speed selector operates properly: • If the snowthrower does not move or moves forward when it is in Position R1, remove the trunnion from the speed selector lever, turn the trunnion downward (clockwise) on the speed control rod, then install the trunnion. • If the snowthrower does not move or moves rearward when it is in Position 1 (forward), remove the trunnion from the speed selector lever, turn the trunnion upward (counterclockwise) on the speed control rod, then install the trunnion. Note: Refer to the relevant steps in Installing the Traction Control Linkage on page 7. Note: If the snowthrower move ...

Moving the Chute Deflector Push and hold the blue trigger cap down and move the Quick Stick forward to lower the chute deflector; move it rearward to raise the chute deflector. Throwing Snow Danger When the snowthrower is in operation, the impeller and auger can rotate and cut off or injure hands and feet.
Before adjusting, cleaning, inspecting, troubleshooting, or repairing the snowthrower, stop the engine and wait for all moving parts to stop. Disconnect the wire from the spark plug and keep it away from the plug to prevent someone from accidentally starting the engine.
Remove an obstruction from the discharge chute; refer to Un ...

Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Interval Maintenance Procedure Each Use • Check the engine oil level and add oil if necessary. Refer to Checking the Engine Oil Level on page 14. After the First 2 Operating Hours • Change the engine oil. Refer to Changing the Engine Oil on page 16. • Inspect the traction cable and adjust it if necessary. Refer to Checking and Adjusting the Traction Cable on page 14. • Inspect the auger/impeller cable and adjust it if necessary. Refer to Checking and Adjusting the Auger/Im ...

Checking the Engine Oil Level Each time before using the snowthrower, check the oil level in the engine crankcase. 1. Remove the dipstick, wipe it clean, then fully install the dipstick. 2. Remove the dipstick and check the oil level. If the oil level is below the Add mark on the dipstick, add oil. Refer to Filling the Engine with Oil on page 8. m-6900 Checking and Adjusting the Skids and Scraper Check the skids and the scraper to ensure that the auger does not contact the paved or gravel surface. Adjust the skids and the scraper as needed to compensate for wear. 1. Check the tire pressure. Refer to Checking the Tire Pressure on page ...

Checking and Adjusting the Auger/Impeller Cable Check and adjust the auger/impeller cable after the first 2 operating hours, then annually thereafter. 1. Remove the 2 screws from the right side of the belt cover as shown. 2. Lift up the right side of the belt cover. m-6922 3. With the auger/impeller lever disengaged, ensure that the gap between the auger clutch assembly and the tab (A) is 1/16 inch (1.5 mm). 1/16 in. (1.5 mm) A A 4. If the auger/impeller cable is not properly adjusted, do the following steps: 5. Loosen the jam nut (A). 6. Loosen or tighten the turnbuckle (B) that adjusts the tension on the cable. m-6903 A B 7. Adjust ...

Changing the Engine Oil Change the engine oil after the first 2 operating hours, then annually thereafter. If possible, run the engine just before changing the oil because warm oil flows better and carries more contaminants. Max. fill: 26 oz. (0.77 l), type: automotive detergent oil with an API service classification of SF, SG, SH, SJ, SL, or higher. • For temperatures above 32°F (0°C), use SAE 30W. • For temperatures between 0°F and 32°F (–18°C to 0°C), use SAE 5W30 or SAE 10W. • For air temperatures below 0°F (–18°C), use SAE 0W30. 1. Clean the area around the oil drain cap (A). m-4036 A 2. Slide an oil drain pan u ...

Storage Warning
Gasoline vapors can explode.
Do not store gasoline more than 30 days.
Do not store the snowthrower in an enclosure near an open flame.
Allow the engine to cool before storing it. Preparing the Snowthrower for Storage 1. On the last refueling of the year, add fuel stabilizer to fresh fuel as directed by the engine manufacturer. 2. Run the engine for 10 minutes to distribute the conditioned fuel through the fuel system. 3. Loosen the hose clamp that secures the fuel line to the valve and slide the fuel line off the fuel shutoff valve. 4. Open the fuel shutoff valve and allow the fuel to drain out of the fuel tank ...

Troubleshooting Toro designed and built your snowthrower for trouble-free operation. Check the following components and items carefully, and refer to Maintenance on page 13 for more information. If a problem continues, see an Authorized Service Dealer. Problem Possible Causes Corrective Action Electric starter does not turn (electric-start models only) 1. The power cord is disconnected at the outlet or the snowthrower. 1. Connect the power cord to the outlet and/or the snowthrower. 2. The power cord is worn, corroded, or damaged. 2. Replace the power cord. 3. The power outlet is not energized. 3. Have a qualified electrician energize ...

Problem Corrective Action Possible Causes 3. The fuel tank is nearly empty or contains stale fuel. 3. Drain and fill the fuel tank with fresh gasoline (not more than 30 days old). If the problem persists, contact an Authorized Service Dealer. 4. The spark plug wire is loose. 4. Connect the wire to the spark plug. 5. The spark plug is pitted, fouled, or the gap is incorrect. 5. Check the spark plug and adjust the gap if necessary. Replace the spark plug if it is pitted, fouled, or cracked. 6. The engine oil level in the engine crankcase is too low or too high. 6. Add or drain the oil level in the engine crankcase to the Full mark on th ...

A Two-Year Full Warranty (Limited Warranty for Commercial Use) Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair any Toro Product used for normal residential purposes* if defective in materials or workmanship. The following time periods apply from the date of purchase: Snow Products Warranty Period • All Products and Attachments 2 year full warranty • Power MaxTM Snow Products: Chute 5 year full warranty Chute Deflector 5 year full warranty Impeller Housing Cover 5 year full warranty T ...