Rohde & Schwarz Smart Instruments UP300 Operating Manual
Read Online
Read the Rohde & Schwarz Smart Instruments UP300 Operating Manual online using the built-in PDF viewer.
Text of the manual
Operating Manual, 11/2007
© Copyright 2007
ROHDE & SCHWARZ GmbH & Co. KG
Test and Measurement Division
Mühldorfstraße 15
81671 München, Germany
4th edition 11/2007
Printed in Germany.
Printed on FFC bleached paper.
Subject to alterations. Errors excepted.
Reprints, also in extracts, are only allowed with written permission of the manufacturer.
All rights reserved.
Operating Manual, 11/2007
1-3
E-1147.2759.00
Chapter Overview
General
Content of the Manuals for the Audio Analyzer R&S UP300/350
Data Sheet
Safety Instructions
Certificate of Quality
EC Certificate of Conformity
Support Center Addresses
List of Rohde & Schwarz Offices
Chapter 1
Introduction
Chapter 2
Control Elements
Chapter 3
Putting the R&S UP300/350 into Operation
Chapter 4
Getting Started – Measurement Example
Chapter 5
Manual Operating Concept
Chapter 6
Working with the R&S UP300/350
Chapter 7
Instrument Interfaces
Chapter 8
Error Messages
Chapter 9
Index
Content of the Manuals
R&S UP300/350
E-1147.2759.00
1-4
Operating Manual, 11/2007
Content of the Manuals
Introduction
This operating manual provides information about:
Technical characteristics of the instrument
Putting into operation
Basic operating procedures and control elements
Operation via menus
In the introduction, a typical R&S UP300/350 measurement is described.
The operating manual also contains information about maintenance and
troubleshooting based on the warnings and error messages issued by the
instrument.
Table of Contents
Operating Manual, 11/2007
1-5
E-1147.2759.00
Table of Contents
Chapter Overview............................................................................................................................ 1-3
Content of the Manuals................................................................................................................... 1-4
Table of Contents............................................................................................................................ 1-5
Data Sheet...................................................................................................................................... 1-11
Analyzer................................................................................................................................... 1-11
Analog audio inputs ..................................................................................................... 1-11
Digital audio inputs (model R&S UP350 only)............................................................. 1-11
Measurement functions ............................................................................................... 1-12
Filters ........................................................................................................................... 1-14
FFT analyzer................................................................................................................ 1-15
Generator................................................................................................................................. 1-15
Analog audio outputs ................................................................................................... 1-15
Digital audio outputs (model R&S UP350 only)........................................................... 1-15
Signals ......................................................................................................................... 1-15
Sweep .......................................................................................................................... 1-17
Display of results ..................................................................................................................... 1-17
Units............................................................................................................................. 1-17
Graphical display of results.......................................................................................... 1-17
Audio monitor............................................................................................................... 1-17
Digital audio protocol (model R&S UP350 only).......................................................... 1-18
General specifications ................................................................................................. 1-18
Safety Instructions ........................................................................................................................ 1-21
Certificate of Quality ..................................................................................................................... 1-31
EC Certificate of Conformity ........................................................................................................ 1-32
Support Center Address............................................................................................................... 1-33
List of Rohde & Schwarz Offices................................................................................................. 1-34
1
Introduction................................................................................................. 1-35
1.1 Application Range of the R&S UP300/350 .......................................................................... 1-35
1.2 Supplied Accessories ........................................................................................................... 1-36
1.3 Warranty ................................................................................................................................. 1-36
2
Control Elements ........................................................................................ 2-37
2.1 Front View .............................................................................................................................. 2-37
2.2 Rear View: R&S UP300/350 .................................................................................................. 2-38
2.3 Rear View: R&S UP350 (Digital Interface)........................................................................... 2-39
3
Putting the R&S UP300/350 into Operation .............................................. 3-40
3.1 Unpacking the R&S UP300/350 ............................................................................................ 3-40
Table of Contents
R&S UP300/350
E-1147.2759.00
1-6
Operating Manual, 11/2007
3.2 Setting up the Instrument ..................................................................................................... 3-40
3.3 Connecting the R&S UP300/350 to the AC Line ................................................................. 3-42
3.4 Switching On the R&S UP300/350 ....................................................................................... 3-42
3.5 Function Test ......................................................................................................................... 3-43
3.6 EMC......................................................................................................................................... 3-43
3.7 Connecting a DUT.................................................................................................................. 3-44
3.8 Connecting an External Keyboard....................................................................................... 3-45
3.9 Connecting a USB Stick........................................................................................................ 3-46
4
Getting Started............................................................................................ 4-47
4.1 Generator and Analyzer Settings......................................................................................... 4-47
5
Manual Operating Concept ........................................................................ 5-51
5.1 Overview of Operating Steps ............................................................................................... 5-52
5.2 Making Entries from the Keypad.......................................................................................... 5-53
5.2.1 Numeric Keys............................................................................................................... 5-54
5.2.2 Main Menu Selection Keys .......................................................................................... 5-54
5.2.3 Rotary Knob................................................................................................................. 5-55
5.2.4 Cursor Keys ................................................................................................................. 5-55
5.2.5 Function Keys .............................................................................................................. 5-55
5.2.6 Action Keys .................................................................................................................. 5-56
5.2.7 BACK/SYS Key............................................................................................................ 5-56
5.3 Screen Display....................................................................................................................... 5-57
5.3.1 Display Area................................................................................................................. 5-58
5.3.2 Menu Area ................................................................................................................... 5-60
5.3.3 Function Area............................................................................................................... 5-60
5.4 Calling and Changing the Menus......................................................................................... 5-61
5.5 Setting the Parameters ......................................................................................................... 5-63
5.5.1 Direct Selection of Instrument Functions..................................................................... 5-63
5.5.2 Toggling a Setting........................................................................................................ 5-63
5.5.3 Selecting Settings ........................................................................................................ 5-64
5.5.4 Entering Numerical Parameters................................................................................... 5-65
5.5.4.1
Entry with the Numeric Keys............................................................. 5-65
5.5.4.2
Entry with the Cursor Keys and Rotary Knob ................................... 5-67
5.6 Overview of all Menus and Functions ................................................................................. 5-69
5.6.1 Generator..................................................................................................................... 5-69
5.6.1.1
FUNCTIONS Menu ........................................................................... 5-69
5.6.1.2
SINE Menu........................................................................................ 5-69
5.6.1.3
NOISE Menu ..................................................................................... 5-70
5.6.1.4
MULTISINE Menu ............................................................................. 5-70
5.6.1.5
SINE BURST Menu........................................................................... 5-71
5.6.1.6
MOD DIST Menu............................................................................... 5-71
5.6.1.7
DFD Menu......................................................................................... 5-71
Table of Contents
Operating Manual, 11/2007
1-7
E-1147.2759.00
5.6.1.8
POLARITY TEST Menu .................................................................... 5-72
5.6.1.9
DC OFFSET Menu............................................................................ 5-72
5.6.1.10
SWEEP RMS Menu .......................................................................... 5-73
5.6.1.11
SWEEP RMS SELECTIVE Menu ..................................................... 5-74
5.6.1.12
SWEEP THD Menu........................................................................... 5-75
5.6.1.13
MONITOR Menu ............................................................................... 5-76
5.6.1.14
CONFIG Menu .................................................................................. 5-76
5.6.2 Analyzer ....................................................................................................................... 5-77
5.6.2.1
FUNCTIONS Menu ........................................................................... 5-77
5.6.2.2
FREQUENCY, DC, RMS Menu ........................................................ 5-78
5.6.2.3
PEAK Menu....................................................................................... 5-78
5.6.2.4
QUASI PEAK Menu .......................................................................... 5-79
5.6.2.5
RMS SELECTIVE Menu ................................................................... 5-79
5.6.2.6
FFT Menu.......................................................................................... 5-80
5.6.2.7
THD Menu......................................................................................... 5-80
5.6.2.8
DFD Menu......................................................................................... 5-81
5.6.2.9
PHASE Menu .................................................................................... 5-81
5.6.2.10
MOD DIST Menu............................................................................... 5-82
5.6.2.11
PROTOCOL Menu............................................................................ 5-82
5.6.2.12
SAMPLE RATE Menu....................................................................... 5-82
5.6.2.13
FILTER Menu.................................................................................... 5-83
5.6.2.14
CONFIG Menu .................................................................................. 5-83
5.6.3 Graph Menu................................................................................................................. 5-84
5.6.3.1
GRAPH MODE Menu........................................................................ 5-84
5.6.3.2
X AXIS Menu..................................................................................... 5-84
5.6.3.3
Y AXIS Menu..................................................................................... 5-84
5.6.3.4
CURSORS Menu .............................................................................. 5-85
5.6.4 System menu (SYS Menu) .......................................................................................... 5-87
5.6.4.1
PRESET Menu.................................................................................. 5-87
5.6.4.2
STATE Menu..................................................................................... 5-87
5.6.4.3
FILE Menu......................................................................................... 5-87
5.6.4.4
CONFIG Menu .................................................................................. 5-88
5.6.4.5
SERVICE Menu ................................................................................ 5-88
5.6.4.6
INFO Menu........................................................................................ 5-88
5.6.4.7
CALIB Menu...................................................................................... 5-88
6
Working with the R&S UP300/350.............................................................. 6-89
6.1 Factory Default Settings ....................................................................................................... 6-89
6.1.1 Generator..................................................................................................................... 6-90
6.1.2 Analyzer ....................................................................................................................... 6-94
6.1.3 Graph ........................................................................................................................... 6-97
6.1.4 System ......................................................................................................................... 6-97
6.2 Generator................................................................................................................................ 6-98
6.2.1 Configuring Generator Parameters (CONFIG)............................................................ 6-99
6.2.1.1
Selecting the Generator Type – Analog/Digital (R&S UP350 only) 6-101
6.2.1.2
Analog Generator............................................................................ 6-102
Table of Contents
R&S UP300/350
E-1147.2759.00
1-8
Operating Manual, 11/2007
6.2.1.2.1
Selecting the Generator Bandwidth ................................................ 6-102
6.2.1.2.2
Selecting the Reference Potential of the Output Signal.................. 6-103
6.2.1.2.3
Activating/Deactivating the Generator Output ................................ 6-104
6.2.1.2.4
Selecting the Type of the Level Range Switchover ........................ 6-105
6.2.1.3
Digital Generator (R&S UP350 only) .............................................. 6-107
6.2.1.3.1
Selecting the Sample Frequency of the Output Signal................... 6-107
6.2.1.3.2
Entering the Sample Frequency Offset........................................... 6-108
6.2.1.3.3
Setting the Validity Bit ..................................................................... 6-108
6.2.1.3.4
Selecting the Valid Number of Bits in the Output Signal................. 6-109
6.2.1.3.5
Selecting the Interface Protocol...................................................... 6-109
6.2.2 Setting the Generator Signal Type (FUNCTIONS).................................................... 6-110
6.2.2.1
Selecting Generator Functions ....................................................... 6-112
6.2.2.2
Configuring Signal Parameters....................................................... 6-113
6.2.2.2.1
SINE (Sinewave Signal).................................................................. 6-114
6.2.2.2.2
NOISE (Noise Signal) ..................................................................... 6-119
6.2.2.2.3
MULTISINE (Multitone Signal)........................................................ 6-122
6.2.2.2.4
SINE BURST (Sine Burst Signal) ................................................... 6-132
6.2.2.2.5
MOD DIST (Two-Tone Signal in Accordance with IEC) ................. 6-138
6.2.2.2.6
DFD (Difference Frequency Signal)................................................ 6-144
6.2.2.2.7
POLARITY TEST (Polarization Test Signal)................................... 6-150
6.2.2.2.8
DC OFFSET (DC Voltage Component) .......................................... 6-152
6.2.2.2.9
SWEEP RMS .................................................................................. 6-154
6.2.2.2.10
SWEEP RMS SELECTIVE ............................................................. 6-171
6.2.2.2.11
SWEEP THD................................................................................... 6-190
6.2.3 Audio Monitoring Output (MONITOR) ....................................................................... 6-209
6.3 Analyzer................................................................................................................................ 6-212
6.3.1 Configuring the Analyzer (CONFIG).......................................................................... 6-213
6.3.1.1
Selecting the Analyzer Type – Analog/Digital (R&S UP350 only) .. 6-215
6.3.1.2
Analog Analyzer .............................................................................. 6-216
6.3.1.2.1
Selecting the Analyzer Bandwidth .................................................. 6-216
6.3.1.2.2
Selecting the Reference Potential of the Input Signal .................... 6-217
6.3.1.2.3
Selecting the Signal Source............................................................ 6-218
6.3.1.2.4
Selecting the Signal Coupling ......................................................... 6-219
6.3.1.2.5
Selecting the Measurement Range Selection Mode....................... 6-220
6.3.1.2.6
Selecting the Measurement Channel.............................................. 6-221
6.3.1.3
Digital Analyzer (R&S UP350 only)................................................. 6-222
6.3.1.3.1
Selecting the Sample Frequency of the Input Signal...................... 6-222
6.3.1.3.2
Selecting the Input Signal ............................................................... 6-223
6.3.1.3.3
Selecting the Valid Number of Bits in the Input Signal ................... 6-223
6.3.2 Setting the Measurement Functions (FUNCTIONS) ................................................. 6-224
6.3.2.1
Selecting the Measurement Functions............................................ 6-226
6.3.2.2
Configuring the Measurement Parameters..................................... 6-227
6.3.2.2.1
FREQUENCY, DC, RMS ................................................................ 6-228
6.3.2.2.2
PEAK (Peak Value)......................................................................... 6-237
6.3.2.2.3
QUASI PEAK (Quasi Peak Value) .................................................. 6-243
6.3.2.2.4
RMS SELECTIVE (Selective RMS value)....................................... 6-246
6.3.2.2.5
FFT (Frequency-Domain Display, Spectrum)................................. 6-251
6.3.2.2.6
THD, THD+N, SINAD (Total Harmonic Distortion) ......................... 6-259
6.3.2.2.7
POLARITY (Polarity Test)............................................................... 6-267
6.3.2.2.8
DFD (Difference Frequency Distortion) .......................................... 6-268
6.3.2.2.9
PHASE (Measuring the Phase Difference Between Channels) ..... 6-272
6.3.2.2.10
MOD DIST (Modulation Distortion) ................................................. 6-275
6.3.2.2.11
PROTOCOL (Protocol Analysis), (R&S UP350 only) ..................... 6-278
6.3.2.2.12
SAMPLE RATE (Sample Frequency), (R&S UP350 only).............. 6-281
Table of Contents
Operating Manual, 11/2007
1-9
E-1147.2759.00
6.3.3 Configuring the Filters (FILTER)................................................................................ 6-282
6.3.3.1
Selecting the Filters......................................................................... 6-283
6.3.4 Starting and Stopping the Measurements ................................................................. 6-285
6.4 Graph Menu.......................................................................................................................... 6-286
6.4.1 Selecting the Display Mode (GRAPH MODE)........................................................... 6-287
6.4.1.1
Selecting the Display Parameters................................................... 6-288
6.4.1.2
Selecting the Display Mode............................................................. 6-290
6.4.2 Scaling the X Axis (X AXIS)....................................................................................... 6-292
6.4.2.1
Setting the Display Range............................................................... 6-293
6.4.2.2
Selecting the Display Mode............................................................. 6-295
6.4.3 Scaling the Y Axis (Y AXIS)....................................................................................... 6-296
6.4.3.1
Setting the Display Range............................................................... 6-297
6.4.3.2
Selecting the Display Mode............................................................. 6-299
6.4.4 Trace Analysis Using Cursors (CURSORS).............................................................. 6-300
6.4.4.1
Configuring the X Cursors............................................................... 6-301
6.4.4.1.1
Activating/Deactivating the X Cursors............................................. 6-302
6.4.4.1.2
Assigning the X Cursors to a Trace (Ch 1 or Ch 2) ........................ 6-303
6.4.4.1.3
Positioning the X Cursors on a Maximum....................................... 6-303
6.4.4.1.4
Manual Positioning the X Cursors................................................... 6-305
6.4.4.1.5
Zooming the Display Area............................................................... 6-307
6.4.4.2
Configuring the Y Cursors............................................................... 6-309
6.4.4.2.1
Activating/Deactivating the Y Cursors............................................. 6-310
6.4.4.2.2
Manual Positioning the Y Cursors................................................... 6-311
6.4.4.2.3
Zooming the Display Area............................................................... 6-312
6.4.5 Full-Screen Display.................................................................................................... 6-314
6.5 System Menu (SYS Menu key)............................................................................................ 6-316
6.5.1 Instrument Default Setting (PRESET Menu) ............................................................. 6-317
6.5.1.1
Selecting and Calling the Instrument Default Setting ..................... 6-318
6.5.1.2
Start the Remote Control Manually................................................. 6-319
6.5.2 Displaying the Current Instrument Setting (STATE Menu)........................................ 6-320
6.5.3 User-Defined Settings (FILE Menu) .......................................................................... 6-322
6.5.3.1
Saving and Loading a User-Defined Settings................................. 6-323
6.5.3.2
Printing out a Screenshot................................................................ 6-325
6.5.3.3
Saving the Measurement Results................................................... 6-327
6.5.4 System Settings (CONFIG Menu) ............................................................................. 6-328
6.5.4.1
Setting the Date and Time .............................................................. 6-329
6.5.4.2
Selecting an Internal or External Reference Sources..................... 6-331
6.5.4.3
Configuring the Instrument Interfaces............................................. 6-332
6.5.4.4
Setting the Screen Saver Mode ...................................................... 6-334
6.5.4.5
Selecting the Internal or External Monitors..................................... 6-336
6.5.5 Service Functions (SERVICE Menu)......................................................................... 6-337
6.5.5.1
Performing the Selftests.................................................................. 6-337
6.5.6 System Information (INFO Menu).............................................................................. 6-338
6.5.6.1
Displaying the Module Data ............................................................ 6-339
6.5.6.2
Displaying the Instrument Statistics................................................ 6-339
6.5.6.3
Displaying the System Messages................................................... 6-340
6.5.7 Adjustment Functions (CALIB Menu) ........................................................................ 6-341
Operating Manual, 11/2007
6.5.7.1
Starting the Auto Adjustment of the Generator Module.................. 6-342
6.5.7.2
Starting the Auto Adjustment of the Analyzer Module .................... 6-342
6.5.7.3
Starting the Auto Adjustment of the R&S UP300/350..................... 6-343
7
Instrument Interfaces ............................................................................... 7-344
7.1 Keyboard Connector (KEYB).............................................................................................. 7-344
7.2 Monitor Connector (MON)................................................................................................... 7-344
7.3 Reference Input and Output (10 MHz In/Out).................................................................... 7-345
7.4 USB Interface (PC, DEV) ..................................................................................................... 7-345
7.5 Audio Monitoring Output (MON OUT) ............................................................................... 7-345
8
Error Messages......................................................................................... 8-346
8.1 System Messages................................................................................................................ 8-346
8.2 Warnings Indicating Impermissible Operating States..................................................... 8-347
9
Index .......................................................................................................... 9-349
Operating Manual, 11/2007
1-11
E-1147.2759.00
Data Sheet
Note: In a highly innovative company like Rohde & Schwarz, products are
continuously undergoing further development. To obtain information about
new
applications
and
features,
visit
our
Internet
page
at
http://www.smart.rohde-schwarz.com.
Analyzer
Analog audio inputs
Frequency range
DC/10 Hz to 80 kHz
Frequency response
10 Hz to 20 Hz
±0.1 dB
(referenced to 1 kHz)
20 Hz to 22 kHz
±0.05 dB
22 kHz to 40 kHz
±0.1 dB
40 kHz to 80 kHz
±0.25 dB
BNC connectors
2 channels, floating, selectable AC/DC coupling, channel 1 on
front panel, channel 2 on rear panel
Maximum input voltage
rms, sinewave
33 V
Measurement ranges
in steps of 6 dB
0.4 V to 50 V
(max. input 33 V)
Input impedance
inner/outer conductor to ground 100 kΩ
Crosstalk attenuation
frequency < 20 kHz, 600 Ω
source impedance
> 100 dB
Common-mode rejection
at 50 Hz, Vin < 3 V
at 1 kHz, Vin < 3 V
at 16 kHz, Vin < 3 V
> 80 dB
> 75 dB
> 60 dB
Generator output
each input channel switchable to the other generator output
channel
Digital audio inputs (model R&S UP350 only)
BNC connector
unbalanced, grounded, on rear panel
Impedance
75 Ω
Input level (Vpp)
100 mV to 5 V
Optical input
TOSLINK
Channels
1, 2, or both
Audio bits
16 to 24
Sampling rate
32 kHz, 44.1 kHz, 48 kHz,
96 kHz, 192 kHz
Operating Manual, 11/2007
Format
professional and consumer
Measurement functions
RMS value, wideband
Error limits
measurement speed AUTO, at
1 kHz sine, AC coupling
measurement speed AUTO
FAST
±0.1 dB, additional error with
DC coupling
±0.1 % of measurement range
±0.1 dB additional error
Integration time
AUTO FAST/AUTO VALUE
5 ms/50 ms, at least 1 cycle
1 ms to 10 s
Noise
with A filter, 600 Ω source
impedance
with CCIR unweighting filter,
600 Ω source impedance
< 2 µV
< 4 µV
Filters
weighting filters and sets of predefined octave and third-octave
filters; up to 3 filters can be combined
RMS value, selective
Error limits
±0.2 dB
Bandwidth (-3 dB)
Relative
Absolute
1%, 3%, 1/3 octave,
1/12 octave, value
minimum BW 10 Hz
10 Hz to fmax/5
Selectivity
100 dB
Frequency setting
fixed through entered value or
autotuning
Peak value
Measurement
pos. peak, neg. peak,
peak-to-peak, absolute peak
Error limits
at 1 kHz
±0.2 dB
Interval
20 ms to 10 s
Filters
weighting filters and sets of predefined octave and third-octave
filters; up to 3 filters can be combined
Quasi-peak
Measurement
in accordance with CCIR 468-4
Error limits
analyzer bandwidth 22 kHz
in accordance with CCIR 468-4
Noise
with CCIR weighting filter,
600 Ω source impedance
<12 µV
Filters
weighting filters and sets of predefined octave and third-octave
filters; up to 3 filters can be combined
Operating Manual, 11/2007
1-13
E-1147.2759.00
DC voltage
Voltage range
0 V to ±33 V
Error limits
± (1 % of measured value +
0.5 % of measurement range)
Total harmonic distortion (THD)
Fundamental
20 Hz to 20 kHz
Frequency tuning
fixed through entered value,
auto-tuning to input signal
Weighted harmonics
up to 80 kHz
any combination of d2 to d9
Error limits
harmonics < 50 kHz
harmonics < 80 kHz
±0.7 dB
±1 dB
Inherent distortion
fundamental 1 kHz
fundamental 20 Hz to 5 kHz
fundamental 5 kHz to 15 kHz
fundamental 15 kHz to 20 kHz
< -100 dB
< -90 dB
< -85 dB
< -80 dB
Spectrum
bar graph showing signal and distortion
THD+N and SINAD
Fundamental
20 Hz to 20 kHz
Frequency tuning
fixed through entered value,
auto-tuning to input signal
Bandwidth
weighting filters and sets of predefined octave and third-octave
filters; up to 3 filters can be combined
Error limits
bandwidth < 22 kHz
bandwidth < 80 kHz
±0.8 dB
±1.4 dB
Inherent distortion
bandwidth 20 Hz to 22 kHz,
fundamental 1 kHz
bandwidth 20 Hz to 22 kHz,
fundamental 20 Hz to 5 kHz
bandwidth 20 Hz to 80 kHz,
fundamental 20 Hz to 20 kHz
< -95 dB + 4 µV
< -90 dB + 4 µV
< 80 dB + 8 µV
Spectrum
post-FFT of filtered signal
Difference frequency distortion
(DFD)
Measurement method
in accordance with IEC 268-3
or IEC 118
Frequency range
difference frequency
center frequency
80 Hz to 2 kHz
200 Hz to 80 kHz
Error limits
fcenter < 20 kHz
±0.5 dB
Inherent distortion
DFD d2, fcenter < 20 kHz
DFD d3, 5 kHz < fcenter < 20 kHz
< -105 dB
< -90 dB
Operating Manual, 11/2007
Spectrum
bar graph showing signal and distortion
Modulation distortion (MOD DIST)
Frequency range
lower frequency
upper frequency
30 Hz to 2.7 kHz
8 × flower to 20 kHz
Error limits
±0.5 dB
Inherent distortion
flower = 60 Hz,
4 kHz < fupper < 15 kHz
flower = 60 Hz,
15 kHz < fupper < 20 kHz
input voltage ≤ 4 V
input voltage > 4 V
< -85 dB
< -80 dB
< -75 dB
Spectrum
bar graph showing signal and distortion
Frequency
Frequency range
20 Hz to 80 kHz
Error limits
measurement time 10 s
measurement time 1 s
±10 ppm
±100 ppm
Phase
Frequency range
analyzer bandwidth 22 kHz
analyzer bandwidth 80 kHz
20 Hz to 22 kHz
80 Hz to 80 kHz
Error limits
f < 20 kHz, both channels with
same range
±1°
Polarity test
Measurement
polarity of unsymmetrical input
signal
Display
positive/negative
Filters
For all analog and digital analyzers. Up to three filters can be
combined. All filters are digital filters with a coefficient accuracy
of 32 bit floating point.
Weighting filters
A weighting
C message
CCITT
CCIR unweighted
CCIR 1k weighted
CCIR 2k weighted
deemphasis 50/15, 50, 75, J.17
IEC/IEEE tuner
Set of third-octave and octave filters
Operating Manual, 11/2007
1-15
E-1147.2759.00
FFT analyzer
Frequency range
DC to 80 kHz
FFT size
1 k, 2 k, 4 k, 8 k, 16 k points
Window functions
rectangular, Hann, Blackman-
Harris, Rife-Vincent 1 to 3,
Hamming, flat top,
Kaiser (β = 12)
Resolution
16 k points, bandwidth 22 kHz
2.93 Hz
Averaging
exponential or normal
1 to 256
Generator
Analog audio outputs
BNC connectors
2 channels, electronic, floating (max. 0.2 V peak referenced to
ground) or grounded, short-circuit-proof, max. current 120 mA
with external feed
channel 1 on front panel, channel 2 on rear panel
Voltage range
sine, open-circuit
0.1 mV to 7.5 V (Vrms)
Source impedance
27 Ω
Crosstalk attenuation
f < 20 kHz
> 100 dB
Load impedance
> 200 Ω
Common-mode rejection
at 1 kHz
> 50 dB
Digital audio outputs
(model R&S UP350 only)
Frequency limits specified for the signals apply to a sampling
rate of 48 kHz. For other sampling rates, limits are calculated in
accordance with the following formula: fnew = f48kHz × sampling
rate/48 kHz.
BNC connectors
unbalanced, transformer coupling, on rear panel
Impedance
75 Ω, short-circuit-proof
Output level (Vpp)
into 75 Ω
0.5 V
Optical output
TOSLINK
Channels
1, 2, or both
Audio bits
16 to 24
Sampling rate
32 kHz, 44.1 kHz, 48 kHz,
96 kHz, 192 kHz
Format
professional and consumer
Signals
Operating Manual, 11/2007
Sine
Frequency range
2 Hz to 80 kHz
Error limits
at 1 kHz
±0.1 dB
Frequency response (ref. to 1 kHz)
20 Hz to 20 kHz
±0.05 dB
Inherent distortion THD+N
measurement bandwidth 20 Hz
to 22 kHz
< -90 dB
Sweep parameters
frequency, level
MOD DIST
for measuring modulation distortion
Frequency range
lower frequency
upper frequency
30 Hz to 2700 Hz
8 × flower to 39.95 kHz
Level ratio (LF:UF)
selectable
from 10:1 to 1:1
Error limits
±0.5 dB
Inherent distortion
at 60 Hz, 7 kHz, level ratio 4:1
other settings; fupper < 20 kHz
< -90 dB
< -84 dB
DFD
for measuring difference frequency distortion
Frequency range
difference frequency
center frequency
80 Hz to 2 kHz
200 Hz to 39.95 kHz
Error limits
±0.5 dB
Inherent distortion
DFD d2, 7 kHz < fcenter < 20 kHz
DFD d3, 7 kHz < fcenter < 20 kHz
< -105 dB
< -90 dB
Multisine
Frequency range
2.4 Hz to 80 kHz
Minimum frequency spacing
bandwidth 22 kHz
2.4 Hz
Dynamic range
referenced to peak value
100 dB
Characteristics
1 to 17 spectral lines, level,
start phase and frequency
selectable for each line
Sine burst
Burst time
1 signal period up to 60 s
Interval time
burst time up to 60 s
Low level
zero to burst level, absolute or
relative to burst
Noise
Distribution
Gaussian, triangular,
rectangular
Polarity test signal
Operating Manual, 11/2007
1-17
E-1147.2759.00
SINE2 BURST signal
1.2 kHz
ON-TIME
1 cycle
INTERVAL
2 cycles
Sweep
Generator function
Sine
Sweep parameters
frequency and/or level
Sweep spacing
linear, logarithmic
Sweep Modes
Single, continuous
Coupled analyzer functions
RMS; RMS Sel.; THD(N)
Sweep Points
X-Axis
Z-Axis (Freq. & Ampl. Sweep)
2 to 1024
1 to 10
Display of results
Units
Level (analog)
V, dBu, dBV, dBm and dBr (ratio to reference value)
Level (digital)
FS, %FS, dBFS and dBr (ratio to reference value)
Distortion
% or dB
Frequency
Hz
Phase
deg
Graphical display of results
Display modes
spectrum plot
curve plot
bar graph
lists of results
Display functions
autoscale
x-axis zoom
full-screen and part-screen mode
2 vertical, 2 horizontal cursor lines
search function for max. values
Audio monitor
Headphone connector
3.5 mm jack
Output voltage
< 2 V
Operating Manual, 11/2007
Output current
< 20 mA
Source impedance
10 Ω, short-circuit-proof
Recommended headphone
impedance
600 Ω
Digital audio protocol
(model R&S UP350 only)
Generator
Validity bit
NONE, L+R
Channel status data
predefined masks for
professional or consumer
format in acc. with IEC 60958
Analyzer
Display of protocol bits
validity bit
L or R
channel status bits
mnemonic display of data
fields, predefined settings for
professional or consumer
format in acc. with IEC 60958;
automatically detected
error indication
block errors, sequence errors,
preamble errors
Clock rate measurement
error limits
±50 ppm
General specifications
Interfaces
USB host
printer; USB stick
A plug, protocol version 1.1
USB device
device-specific command set,
remote control via Windows
driver (Windows XP/2000)
B plug, protocol version 1.1
Connector for external monitor
(VGA)
15-pin D-Sub female
Keyboard connector
PS/2 female
Display
Type
5.4“ active TFT color display
Resolution
320 × 240 pixels
Max. refresh rate
10 pictures/s, nominal
Power supply
Input voltage range
autoranging
100 V to 240 V (AC),
50 Hz to 60 Hz
Power consumption
< 120 VA
Operating Manual, 11/2007
1-19
E-1147.2759.00
Ambient conditions
Operating temperature range
meets EN 60068-2-1/2
+5 °C to +45 °C
Storage temperature range
-20 °C to +70 °C
Relative humidity
meets EN 60068-2-78
(non-condensing)
95 % at +40 °C
Mechanical resistance
Sinusoidal vibration
meets EN 60068-2-6,
EN 61010-1 and
MIL-T-28800D class 5
5 Hz to 150 Hz,
max. 2g at 55 Hz,
55 Hz to 150 Hz:
0.5g constant
Random vibration
meets EN 60068-2-64
10 Hz to 500 Hz: 1.9g
Shock
meets EN 60068-2-27 and
MIL-STD-810
shock spectrum
Electromagnetic compatibility
meets EN 55011 class B and
EN 61326 (EMC Directive of
EU (89/336/EEC))
EMI field strength
10 V/m
Safety
EN 61010-1/IEC 61010-1, UL
3111-1; CSA C22.2 No. 1010.1
Dimensions (W × H × D)
219 mm × 147 mm × 350 mm
Weight
9 kg
Before putting the product into operation for
the first time, make sure to read the following
S a f e t y I n s t r u c t i o n s
All plants and locations of the Rohde & Schwarz group of companies make every effort to keep the
safety standard of our products up to date and to offer our customers the highest possible degree of
safety. Our products and the auxiliary equipment required for them are designed and tested in
accordance with the relevant safety standards. Compliance with these standards is continuously
monitored by our quality assurance system. The product described here has been designed and tested
in accordance with the EC Certificate of Conformity and has left the manufacturer’s plant in a condition
fully complying with safety standards. To maintain this condition and to ensure safe operation, observe
all instructions and warnings provided in this manual. If you have any questions regarding these safety
instructions, the Rohde & Schwarz group of companies will be happy to answer them.
Furthermore, it is your responsibility to use the product in an appropriate manner. This product is
designed for use solely in industrial and laboratory environments or in the field and must not be used in
any way that may cause personal injury or property damage. You are responsible if the product is used
for an intention other than its designated purpose or in disregard of the manufacturer's instructions. The
manufacturer shall assume no responsibility for such use of the product.
The product is used for its designated purpose if it is used in accordance with its product documentation
and within its performance limits (see data sheet, documentation, the following safety instructions).
Using the product requires technical skills and a basic knowledge of English. It is therefore essential
that the product be used exclusively by skilled and specialized staff or thoroughly trained personnel with
the required skills. If personal safety gear is required for using Rohde & Schwarz products, this will be
indicated at the appropriate place in the product documentation.
Symbols and safety labels
Observe
product
documentation
Weight
indication for
units >18 kg
Danger of
electric
shock
Warning!
Hot
surface
PE terminal
Ground
Ground
terminal
Attention!
Electrostatic
sensitive
devices
Supply
voltage
ON/OFF
Standby
indication
Direct
current
(DC)
Alternating
current (AC)
Direct/alternating
current (DC/AC)
Device fully
protected by
double/reinforced
insulation
Observing the safety instructions will help prevent personal injury or damage of any kind caused by
dangerous situations. Therefore, carefully read through and adhere to the following safety instructions
before putting the product into operation. It is also absolutely essential to observe the additional safety
instructions on personal safety that appear in relevant parts of the product documentation. In these
safety instructions, the word "product" refers to all merchandise sold and distributed by the Rohde &
Schwarz group of companies, including instruments, systems and all accessories.
Tags and their meaning
DANGER
This tag indicates a definite hazard carrying a high risk of death or
serious injury if not avoided.
WARNING
This tag indicates a possible hazard carrying a medium risk of death or
(serious) injury if not avoided.
CAUTION
This tag indicates a hazard carrying a low risk of minor or moderate
injury if not avoided.
ATTENTION
This tag indicates the possibility of incorrect use that can cause damage
to the product.
NOTE
This tag indicates a situation where the user should pay special attention
to operating the product but which does not lead to damage.
These tags are in accordance with the standard definition for civil applications in the European
Economic Area. Definitions that deviate from the standard definition may also exist in other economic
areas or military applications. It is therefore essential to make sure that the tags described here are
always used only in connection with the related product documentation and the related product. The
use of tags in connection with unrelated products or documentation can result in misinterpretation and
thus contribute to personal injury or material damage.
Basic safety instructions
1. The product may be operated only under
the operating conditions and in the
positions specified by the manufacturer. Its
ventilation must not be obstructed during
operation. Unless otherwise specified, the
following requirements apply to
Rohde & Schwarz products:
prescribed operating position is always with
the housing floor facing down, IP protection
2X, pollution severity 2, overvoltage
category 2, use only in enclosed spaces,
max. operation altitude 2000 m above sea
level, max. transport altitude 4500 m above
sea level.
Unless specified otherwise in the data
sheet, a tolerance of ±10% shall apply to
the nominal voltage and of ±5% to the
nominal frequency.
2. Applicable local or national safety
regulations and rules for the prevention of
accidents must be observed in all work
performed. The product may be opened
only by authorized, specially trained
personnel. Prior to performing any work on
the product or opening the product, the
product must be disconnected from the
supply network. Any adjustments,
replacements of parts, maintenance or
repair must be carried out only by technical
personnel authorized by Rohde & Schwarz.
Only original parts may be used for
replacing parts relevant to safety (e.g.
power switches, power transformers,
fuses). A safety test must always be
performed after parts relevant to safety
have been replaced (visual inspection, PE
conductor test, insulation resistance
measurement, leakage current
measurement, functional test).
3. As with all industrially manufactured goods,
the use of substances that induce an
allergic reaction (allergens, e.g. nickel)
such as aluminum cannot be generally
excluded. If you develop an allergic
reaction (such as a skin rash, frequent
sneezing, red eyes or respiratory
difficulties), consult a physician immediately
to determine the cause.
4. If products/components are mechanically
and/or thermically processed in a manner
that goes beyond their intended use,
hazardous substances (heavy-metal dust
such as lead, beryllium, nickel) may be
released. For this reason, the product may
only be disassembled, e.g. for disposal
purposes, by specially trained personnel.
Improper disassembly may be hazardous to
your health. National waste disposal
regulations must be observed.
5. If handling the product yields hazardous
substances or fuels that must be disposed
of in a special way, e.g. coolants or engine
oils that must be replenished regularly, the
safety instructions of the manufacturer of
the hazardous substances or fuels and the
applicable regional waste disposal
regulations must be observed. Also
observe the relevant safety instructions in
the product documentation.
6. Depending on the function, certain products
such as RF radio equipment can produce
an elevated level of electromagnetic
radiation. Considering that unborn life
requires increased protection, pregnant
women should be protected by appropriate
measures. Persons with pacemakers may
also be endangered by electromagnetic
radiation. The employer/operator is
required to assess workplaces where there
is a special risk of exposure to radiation
and, if necessary, take measures to avert
the danger.
7. Operating the products requires special
training and intense concentration. Make
certain that persons who use the products
are physically, mentally and emotionally fit
enough to handle operating the products;
otherwise injuries or material damage may
occur. It is the responsibility of the
employer to select suitable personnel for
operating the products.
8. Prior to switching on the product, it must be
ensured that the nominal voltage setting on
the product matches the nominal voltage of
the AC supply network. If a different voltage
is to be set, the power fuse of the product
may have to be changed accordingly.
9. In the case of products of safety class I with
movable power cord and connector,
operation is permitted only on sockets with
earthing contact and protective earth
connection.
10. Intentionally breaking the protective earth
connection either in the feed line or in the
product itself is not permitted. Doing so can
result in the danger of an electric shock
from the product. If extension cords or
connector strips are implemented, they
must be checked on a regular basis to
ensure that they are safe to use.
11. If the product has no power switch for
disconnection from the AC supply, the plug
of the connecting cable is regarded as the
disconnecting device. In such cases, it
must be ensured that the power plug is
easily reachable and accessible at all times
(corresponding to the length of connecting
cable, approx. 2 m). Functional or
electronic switches are not suitable for
providing disconnection from the AC
supply. If products without power switches
are integrated in racks or systems, a
disconnecting device must be provided at
the system level.
12. Never use the product if the power cable is
damaged. Check the power cable on a
regular basis to ensure that it is in proper
operating condition. By taking appropriate
safety measures and carefully laying the
power cable, ensure that the cable cannot
be damaged and that no one can be hurt by
e.g. tripping over the cable or suffering an
electric shock.
13. The product may be operated only from
TN/TT supply networks fused with max.
16 A (higher fuse only after consulting with
the Rohde & Schwarz group of companies).
14. Do not insert the plug into sockets that are
dusty or dirty. Insert the plug firmly and all
the way into the socket. Otherwise, this can
result in sparks, fire and/or injuries.
15. Do not overload any sockets, extension
cords or connector strips; doing so can
cause fire or electric shocks.
16. For measurements in circuits with voltages
Vrms > 30 V, suitable measures (e.g.
appropriate measuring equipment, fusing,
current limiting, electrical separation,
insulation) should be taken to avoid any
hazards.
17. Ensure that the connections with
information technology equipment comply
with IEC 950/EN 60950.
18. Unless expressly permitted, never remove
the cover or any part of the housing while
the product is in operation. Doing so will
expose circuits and components and can
lead to injuries, fire or damage to the
product.
19. If a product is to be permanently installed,
the connection between the PE terminal on
site and the product's PE conductor must
be made first before any other connection
is made. The product may be installed and
connected only by a license electrician.
20. For permanently installed equipment
without built-in fuses, circuit breakers or
similar protective devices, the supply circuit
must be fused in such a way that suitable
protection is provided for users and
products.
21. Do not insert any objects into the openings
in the housing that are not designed for this
purpose. Never pour any liquids onto or into
the housing. This can cause short circuits
inside the product and/or electric shocks,
fire or injuries.
22. Use suitable overvoltage protection to
ensure that no overvoltage (such as that
caused by a thunderstorm) can reach the
product. Otherwise the operating personnel
will be endangered by electric shocks.
23. Rohde & Schwarz products are not
protected against penetration of water,
unless otherwise specified (see also safety
instruction 1.). If this is not taken into
account, there exists the danger of electric
shock for the user or damage to the
product, which can also lead to personal
injury.
24. Never use the product under conditions in
which condensation has formed or can form
in or on the product, e.g. if the product was
moved from a cold to a warm environment.
25. Do not close any slots or openings on the
product, since they are necessary for
ventilation and prevent the product from
overheating. Do not place the product on
soft surfaces such as sofas or rugs or
inside a closed housing, unless this is well
ventilated.
26. Do not place the product on heat-
generating devices such as radiators or fan
heaters. The temperature of the
environment must not exceed the maximum
temperature specified in the data sheet.
27. Batteries and storage batteries must not be
exposed to high temperatures or fire. Keep
batteries and storage batteries away from
children. Do not short-circuit batteries and
storage batteries.
If batteries or storage batteries are
improperly replaced, this can cause an
explosion (warning: lithium cells). Replace
the battery or storage battery only with the
matching Rohde & Schwarz type (see
spare parts list). Batteries and storage
batteries must be recycled and kept
separate from residual waste. Batteries and
storage batteries that contain lead, mercury
or cadmium are hazardous waste. Observe
the national regulations regarding waste
disposal and recycling.
28. Please be aware that in the event of a fire,
toxic substances (gases, liquids etc.) that
may be hazardous to your health may
escape from the product.
29. The product can be very heavy. Be careful
when moving it to avoid back or other
physical injuries.
30. Do not place the product on surfaces,
vehicles, cabinets or tables that for reasons
of weight or stability are unsuitable for this
purpose. Always follow the manufacturer's
installation instructions when installing the
product and fastening it to objects or
structures (e.g. walls and shelves).
31. Handles on the products are designed
exclusively for personnel to hold or carry
the product. It is therefore not permissible
to use handles for fastening the product to
or on means of transport such as cranes,
fork lifts, wagons, etc. The user is
responsible for securely fastening the
products to or on the means of transport
and for observing the safety regulations of
the manufacturer of the means of transport.
Noncompliance can result in personal injury
or material damage.
32. If you use the product in a vehicle, it is the
sole responsibility of the driver to drive the
vehicle safely. Adequately secure the
product in the vehicle to prevent injuries or
other damage in the event of an accident.
Never use the product in a moving vehicle if
doing so could distract the driver of the
vehicle. The driver is always responsible for
the safety of the vehicle. The manufacturer
assumes no responsibility for accidents or
collisions.
33. If a laser product (e.g. a CD/DVD drive) is
integrated in a Rohde & Schwarz product,
do not use any other settings or functions
than those described in the product
documentation. Otherwise this may be
hazardous to your health, since the laser
beam can cause irreversible damage to
your eyes. Never try to take such products
apart, and never look into the laser beam.
Informaciones de seguridad
1171.0000.42-03.00
Sheet 5
Por favor lea imprescindiblemente antes de
la primera puesta en funcionamiento las
siguientes
Informaciones de seguridad
El principio del grupo de empresas Rohde & Schwarz consiste en tener nuestros productos siempre al
día con los estandards de seguridad y de ofrecer a nuestros clientes el máximo grado de seguridad.
Nuestros productos y todos los equipos adicionales son siempre fabricados y examinados según las
normas de seguridad vigentes. Nuestra sección de gestión de la seguridad de calidad controla
constantemente que sean cumplidas estas normas. El presente producto ha sido fabricado y
examinado según el comprobante de conformidad adjunto según las normas de la CE y ha salido de
nuestra planta en estado impecable según los estandards técnicos de seguridad. Para poder preservar
este estado y garantizar un funcionamiento libre de peligros, el usuario deberá atenerse a todas las
informaciones, informaciones de seguridad y notas de alerta. El grupo de empresas Rohde & Schwarz
está siempre a su disposición en caso de que tengan preguntas referentes a estas informaciones de
seguridad.
Además queda en la responsabilidad del usuario utilizar el producto en la forma debida. Este producto
solamente fue elaborado para ser utilizado en la industria y el laboratorio o para fines de campo y de
ninguna manera deberá ser utilizado de modo que alguna persona/cosa pueda ser dañada. El uso del
producto fuera de sus fines definidos o despreciando las informaciones de seguridad del fabricante
queda en la responsabilidad del usuario. El fabricante no se hace en ninguna forma responsable de
consecuencias a causa del mal uso del producto.
Se parte del uso correcto del producto para los fines definidos si el producto es utilizado dentro de las
instrucciones de la correspondiente documentación de producto y dentro del margen de rendimiento
definido (ver hoja de datos, documentación, informaciones de seguridad que siguen). El uso del
producto hace necesarios conocimientos profundos y conocimientos parciales del idioma inglés. Por
eso se deberá tener en cuenta de exclusivamente autorizar para el uso del producto a personas peritas
o debidamente minuciosamente instruidas con los conocimientos citados. Si fuera necesaria
indumentaria de seguridad para el uso de productos de R&S, encontrará la información debida en la
documentación del producto en el capítulo correspondiente.
Símbolos y definiciones de seguridad
Ver
documen-
tación de
producto
Informaciones
para
maquinaria
con uns peso
de > 18kg
Peligro de
golpe de
corriente
¡Advertencia!
Superficie
caliente
Conexión a
conductor
protector
Conexión
a tierra
Conexión
a masa
conductora
¡Cuidado!
Elementos de
construcción
con peligro de
carga
electroestática
potencia EN
MARCHA/PARADA
Indicación
Stand-by
Corriente
continua
DC
Corriente
alterna AC
Corriente
continua/alterna
DC/AC
El aparato está
protegido en su
totalidad por un
aislamiento de
doble refuerzo
Informaciones de seguridad
1171.0000.42-03.00
Sheet 6
Tener en cuenta las informaciones de seguridad sirve para tratar de evitar daños y peligros de toda
clase. Es necesario de que se lean las siguientes informaciones de seguridad concienzudamente y se
tengan en cuenta debidamente antes de la puesta en funcionamiento del producto. También deberán
ser tenidas en cuenta las informaciones para la protección de personas que encontrarán en el capítulo
correspondiente de la documentación de producto y que también son obligatorias de seguir. En las
informaciones de seguridad actuales hemos juntado todos los objetos vendidos por el grupo de
empresas Rohde & Schwarz bajo la denominación de „producto“, entre ellos también aparatos,
instalaciones así como toda clase de accesorios.
Palabras de señal y su significado
PELIGRO
Identifica un peligro directo con riesgo elevado de provocar muerte o
lesiones de gravedad si no se toman las medidas oportunas.
ADVERTENCIA Identifica un posible peligro con riesgo medio de provocar muerte o
lesiones (de gravedad) si no se toman las medidas oportunas.
ATENCIÓN
Identifica un peligro con riesgo reducido de provocar lesiones de
gravedad media o leve si no se toman las medidas oportunas.
CUIDADO
Indica la posibilidad de utilizar mal el producto y a consecuencia
dañarlo.
INFORMACIÓN Indica una situación en la que deberían seguirse las instrucciones en el
uso del producto, pero que no consecuentemente deben de llevar a un
daño del mismo.
Las palabras de señal corresponden a la definición habitual para aplicaciones civiles en el área
económica europea. Pueden existir definiciones diferentes a esta definición en otras áreas económicas
o en aplicaciones militares. Por eso se deberá tener en cuenta que las palabras de señal aquí descritas
sean utilizadas siempre solamente en combinación con la correspondiente documentación de producto
y solamente en combinación con el producto correspondiente. La utilización de las palabras de señal
en combinación con productos o documentaciones que no les correspondan puede llevar a
malinterpretaciones y tener por consecuencia daños en personas u objetos.
Informaciones de seguridad elementales
1. El producto solamente debe ser utilizado
según lo indicado por el fabricante referente
a la situación y posición de funcionamiento
sin que se obstruya la ventilación. Si no se
convino de otra manera, es para los
productos R&S válido lo que sigue:
como posición de funcionamiento se define
principialmente la posición con el suelo de la
caja para abajo , modo de protección IP 2X,
grado de suciedad 2, categoría de
sobrecarga eléctrica 2, utilizar solamente en
estancias interiores, utilización hasta 2000 m
sobre el nivel del mar, transporte hasta
4.500 m sobre el nivel del mar.
A menos que se especifique otra cosa en la
hoja de datos, se aplicará una tolerancia de
±10% sobre el voltaje nominal y de ±5%
sobre la frecuencia nominal.
2. En todos los trabajos deberán ser tenidas en
cuenta las normas locales de seguridad de
trabajo y de prevención de accidentes. El
producto solamente debe de ser abierto por
personal perito autorizado. Antes de efectuar
trabajos en el producto o abrirlo deberá este
ser desconectado de la corriente. El ajuste,
el cambio de partes, la manutención y la
reparación deberán ser solamente
efectuadas por electricistas autorizados por
R&S. Si se reponen partes con importancia
para los aspectos de seguridad (por ejemplo
el enchufe, los transformadores o los
fusibles), solamente podrán ser sustituidos
por partes originales. Despues de cada
recambio de partes elementales para la
seguridad deberá ser efectuado un control de
seguridad (control a primera vista, control de
conductor protector, medición de resistencia
de aislamiento, medición de medición de la
corriente conductora, control de
funcionamiento).
Informaciones de seguridad
1171.0000.42-03.00
Sheet 7
3. Como en todo producto de fabricación
industrial no puede ser excluido en general
de que se produzcan al usarlo elementos
que puedan generar alergias, los llamados
elementos alergénicos (por ejemplo el
níquel). Si se producieran en el trato con
productos R&S reacciones alérgicas, como
por ejemplo urticaria, estornudos frecuentes,
irritación de la conjuntiva o dificultades al
respirar, se deberá consultar inmediatamente
a un médico para averigurar los motivos de
estas reacciones.
4. Si productos / elementos de construcción son
tratados fuera del funcionamiento definido de
forma mecánica o térmica, pueden generarse
elementos peligrosos (polvos de sustancia
de metales pesados como por ejemplo
plomo, berilio, níquel). La partición elemental
del producto, como por ejemplo sucede en el
tratamiento de materias residuales, debe de
ser efectuada solamente por personal
especializado para estos tratamientos. La
partición elemental efectuada
inadecuadamente puede generar daños para
la salud. Se deben tener en cuenta las
directivas nacionales referentes al
tratamiento de materias residuales.
5. En el caso de que se produjeran agentes de
peligro o combustibles en la aplicación del
producto que debieran de ser transferidos a
un tratamiento de materias residuales, como
por ejemplo agentes refrigerantes que deben
ser repuestos en periodos definidos, o
aceites para motores, deberan ser tenidas en
cuenta las prescripciones de seguridad del
fabricante de estos agentes de peligro o
combustibles y las regulaciones regionales
para el tratamiento de materias residuales.
Cuiden también de tener en cuenta en caso
dado las prescripciones de seguridad
especiales en la descripción del producto.
6. Ciertos productos, como por ejemplo las
instalaciones de radiación HF, pueden a
causa de su función natural, emitir una
radiación electromagnética aumentada. En
vista a la protección de la vida en desarrollo
deberían ser protegidas personas
embarazadas debidamente. También las
personas con un bypass pueden correr
peligro a causa de la radiación
electromagnética. El empresario/usario está
comprometido a valorar y señalar areas de
trabajo en las que se corra un riesgo
aumentado de exposición a radiaciones para
evitar riesgos.
7. La utilización de los productos requiere
instrucciones especiales y una alta
concentración en el manejo. Debe de
ponerse por seguro de que las personas que
manejen los productos estén a la altura de
los requerimientos necesarios referente a
sus aptitudes físicas, psíquicas y
emocionales, ya que de otra manera no se
pueden excluir lesiones o daños de objetos.
El empresario lleva la responsabilidad de
seleccionar el personal usuario apto para el
manejo de los productos.
8. Antes de la puesta en marcha del producto
se deberá tener por seguro de que la tensión
preseleccionada en el producto equivalga a
la del la red de distribución. Si es necesario
cambiar la preselección de la tensión
también se deberán en caso dabo cambiar
los fusibles correspondientes del prodcuto.
9. Productos de la clase de seguridad I con
alimentación móvil y enchufe individual de
producto solamente deberán ser conectados
para el funcionamiento a tomas de corriente
de contacto de seguridad y con conductor
protector conectado.
10. Queda prohibida toda clase de interrupción
intencionada del conductor protector, tanto
en la toma de corriente como en el mismo
producto. Puede tener como consecuencia el
peligro de golpe de corriente por el producto.
Si se utilizaran cables o enchufes de
extensión se deberá poner al seguro, que es
controlado su estado técnico de seguridad.
11. Si el producto no está equipado con un
interruptor para desconectarlo de la red, se
deberá considerar el enchufe del cable de
distribución como interruptor. En estos casos
deberá asegurar de que el enchufe sea de
fácil acceso y nabejo (según la medida del
cable de distribución, aproximadamente
2 m). Los interruptores de función o
electrónicos no son aptos para el corte de la
red eléctrica. Si los productos sin interruptor
están integrados en construciones o
instalaciones, se deberá instalar el interruptor
al nivel de la instalación.
Informaciones de seguridad
1171.0000.42-03.00
Sheet 8
12. No utilice nunca el producto si está dañado el
cable eléctrico. Compruebe regularmente el
correcto estado de los cables de conexión a
red. Asegure a través de las medidas de
protección y de instalación adecuadas de
que el cable de eléctrico no pueda ser
dañado o de que nadie pueda ser dañado
por él, por ejemplo al tropezar o por un golpe
de corriente.
13. Solamente está permitido el funcionamiento
en redes de distribución TN/TT aseguradas
con fusibles de como máximo 16 A
(utilización de fusibles de mayor amperaje
sólo previa consulta con el grupo de
empresas Rohde & Schwarz).
14. Nunca conecte el enchufe en tomas de
corriente sucias o llenas de polvo. Introduzca
el enchufe por completo y fuertemente en la
toma de corriente. Si no tiene en
consideración estas indicaciones se arriesga
a que se originen chispas, fuego y/o heridas.
15. No sobrecargue las tomas de corriente, los
cables de extensión o los enchufes de
extensión ya que esto pudiera causar fuego
o golpes de corriente.
16. En las mediciones en circuitos de corriente
con una tensión de entrada de Ueff > 30 V se
deberá tomar las precauciones debidas para
impedir cualquier peligro (por ejemplo
medios de medición adecuados, seguros,
limitación de tensión, corte protector,
aislamiento etc.).
17. En caso de conexión con aparatos de la
técnica informática se deberá tener en
cuenta que estos cumplan los requisitos de
la EC950/EN60950.
18. A menos que esté permitido expresamente,
no retire nunca la tapa ni componentes de la
carcasa mientras el producto esté en
servicio. Esto pone a descubierto los cables
y componentes eléctricos y puede causar
heridas, fuego o daños en el producto.
19. Si un producto es instalado fijamente en un
lugar, se deberá primero conectar el
conductor protector fijo con el conductor
protector del aparato antes de hacer
cualquier otra conexión. La instalación y la
conexión deberán ser efecutadas por un
electricista especializado.
20. En caso de que los productos que son
instalados fijamente en un lugar sean sin
protector implementado, autointerruptor o
similares objetos de protección, el circuito de
suministro de corriente deberá estar
protegido de manera que usuarios y
productos estén suficientemente protegidos.
21. Por favor, no introduzca ningún objeto que
no esté destinado a ello en los orificios de la
caja del aparato. No vierta nunca ninguna
clase de líquidos sobre o en la caja. Esto
puede producir corto circuitos en el producto
y/o puede causar golpes de corriente, fuego
o heridas.
22. Asegúrese con la protección adecuada de
que no pueda originarse en el producto una
sobrecarga por ejemplo a causa de una
tormenta. Si no se verá el personal que lo
utilice expuesto al peligro de un golpe de
corriente.
23. Los productos R&S no están protegidos
contra el agua si no es que exista otra
indicación, ver también punto 1. Si no se
tiene en cuenta esto se arriesga el peligro de
golpe de corriente para el usario o de daños
en el producto lo cual también puede llevar al
peligro de personas.
24. No utilice el producto bajo condiciones en las
que pueda producirse y se hayan producido
líquidos de condensación en o dentro del
producto como por ejemplo cuando se
desplaza el producto de un lugar frío a un
lugar caliente.
25. Por favor no cierre ninguna ranura u orificio
del producto, ya que estas son necesarias
para la ventilación e impiden que el producto
se caliente demasiado. No pongan el
producto encima de materiales blandos como
por ejemplo sofás o alfombras o dentro de
una caja cerrada, si esta no está
suficientemente ventilada.
26. No ponga el producto sobre aparatos que
produzcan calor, como por ejemplo
radiadores o calentadores. La temperatura
ambiental no debe superar la temperatura
máxima especificada en la hoja de datos.
Informaciones de seguridad
1171.0000.42-03.00
Sheet 9
27. Baterías y acumuladores no deben de ser
expuestos a temperaturas altas o al fuego.
Guardar baterías y acumuladores fuera del
alcance de los niños. No cortocircuitar
baterías ni acumuladores. Si las baterías o
los acumuladores no son cambiados con la
debida atención existirá peligro de explosión
(atención celulas de Litio). Cambiar las
baterías o los acumuladores solamente por
los del tipo R&S correspondiente (ver lista de
piezas de recambio). Las baterías y
acumuladores deben reutilizarse y no deben
acceder a los vertederos. Las baterías y
acumuladores que contienen plomo,
mercurio o cadmio deben tratarse como
residuos especiales. Respete en esta
relación las normas nacionales de
evacuación y reciclaje.
28. Por favor tengan en cuenta que en caso de
un incendio pueden desprenderse del
producto agentes venenosos (gases, líquidos
etc.) que pueden generar daños a la salud.
29. El producto puede poseer un peso elevado.
Muévalo con cuidado para evitar lesiones en
la espalda u otras partes corporales.
30. No sitúe el producto encima de superficies,
vehículos, estantes o mesas, que por sus
características de peso o de estabilidad no
sean aptas para él. Siga siempre las
instrucciones de instalación del fabricante
cuando instale y asegure el producto en
objetos o estructuras (por ejemplo paredes y
estantes).
31. Las asas instaladas en los productos sirven
solamente de ayuda para el manejo que
solamente está previsto para personas. Por
eso no está permitido utilizar las asas para la
sujeción en o sobre medios de transporte
como por ejemplo grúas, carretillas
elevadoras de horquilla, carros etc. El
usuario es responsable de que los productos
sean sujetados de forma segura a los medios
de transporte y de que las prescripciones de
seguridad del fabricante de los medios de
transporte sean tenidas en cuenta. En caso
de que no se tengan en cuenta pueden
causarse daños en personas y objetos.
32. Si llega a utilizar el producto dentro de un
vehículo, queda en la responsabilidad
absoluta del conductor que conducir el
vehículo de manera segura. Asegure el
producto dentro del vehículo debidamente
para evitar en caso de un accidente las
lesiones u otra clase de daños. No utilice
nunca el producto dentro de un vehículo en
movimiento si esto pudiera distraer al
conductor. Siempre queda en la
responsabilidad absoluta del conductor la
seguridad del vehículo. El fabricante no
asumirá ninguna clase de responsabilidad
por accidentes o colisiones.
33. Dado el caso de que esté integrado un
producto de laser en un producto R&S (por
ejemplo CD/DVD-ROM) no utilice otras
instalaciones o funciones que las descritas
en la documentación de producto. De otra
manera pondrá en peligro su salud, ya que el
rayo laser puede dañar irreversiblemente sus
ojos. Nunca trate de descomponer estos
productos. Nunca mire dentro del rayo laser.
DIN EN ISO 9001 : 2000
DIN EN 9100 : 2003
DIN EN ISO 14001 : 2004
DQS REG. NO 001954 QM UM
Certified Quality System
Sehr geehrter Kunde,
Sie haben sich für den Kauf eines
Rohde&Schwarz-Produktes entschie-
den. Hiermit erhalten Sie ein nach
modernsten Fertigungsmethoden
hergestelltes Produkt. Es wurde nach
den Regeln unseres Management-
systems entwickelt, gefertigt und
geprüft.
Das Rohde&Schwarz Management-
system ist zertifiziert nach:
DIN EN ISO 9001:2000
DIN EN 9100:2003
DIN EN ISO 14001:2004
Dear Customer,
you have decided to buy a Rohde&
Schwarz product. You are thus as-
sured of receiving a product that is
manufactured using the most modern
methods available. This product was
developed, manufactured and tested
in compliance with our quality manage-
ment system standards.
The Rohde&Schwarz quality manage-
ment system is certified according to:
DIN EN ISO 9001:2000
DIN EN 9100:2003
DIN EN ISO 14001:2004
Cher Client,
vous avez choisi d‘acheter un produit
Rohde&Schwarz. Vous disposez
donc d‘un produit fabriqué d‘après
les méthodes les plus avancées. Le
développement, la fabrication et les
tests respectent nos normes de ges-
tion qualité.
Le système de gestion qualité de
Rohde&Schwarz a été homologué
conformément aux normes:
DIN EN ISO 9001:2000
DIN EN 9100:2003
DIN EN ISO 14001:2004
QUALITÄTSZERTIFIKAT
CERTIFICATE OF QUALITY
CERTIFICAT DE QUALITÉ
EC Certificate of Conformity
Certificate No.: 2005-33
This is to certify that:
Equipment type
Stock No.
Designation
UP300
1147.2497.03
Audio Analyzer
UP350
1147.2507.03
Audio Analyzer
complies with the provisions of the Directive of the Council of the European Union on the
approximation of the laws of the Member States
- relating to electrical equipment for use within defined voltage limits
(73/23/EEC revised by 93/68/EEC)
- relating to electromagnetic compatibility
(89/336/EEC revised by 91/263/EEC, 92/31/EEC, 93/68/EEC)
Conformity is proven by compliance with the following standards:
EN61010-1 : 2001
EN55011 : 1998 + A1 : 1999 + A2 : 2002, Klasse B
EN61326 : 1997 + A1 : 1998 + A2 : 2001 + A3 : 2003
For the assessment of electromagnetic compatibility, the limits of radio interference for Class
B equipment as well as the immunity to interference for operation in industry have been used
as a basis.
Affixing the EC conformity mark as from 2005
ROHDE & SCHWARZ GmbH & Co. KG
Mühldorfstr. 15, D-81671 München
Munich, 2005-11-03
Central Quality Management MF-QZ / Radde
Technical support – where and when you need it
For quick, expert help with any Rohde & Schwarz equipment, contact one of our
Customer Support Centers. A team of highly qualified engineers provides telephone
support and will work with you to find a solution to your query on any aspect of the
operation, programming or applications of Rohde & Schwarz equipment.
Up-to-date information and upgrades
To keep your Rohde & Schwarz equipment always up-to-date,
please subscribe to our electronic newsletter at
http://www.rohde-schwarz.com/www/response.nsf/newsletterpreselection
or request the desired information and upgrades via email from your Customer Support
Center (addresses see below).
Feedback
We want to know if we are meeting your support needs. If you have any comments
please email us and let us know [email protected].
USA & Canada
Monday to Friday (except US public holidays)
8:00 AM – 8:00 PM Eastern Standard Time (EST)
Tel. from USA
888-test-rsa (888-837-8772) (opt 2)
From outside USA
+1 410 910 7800 (opt 2)
Fax
+1 410 910 7801
E-mail
[email protected]
East Asia
Monday to Friday (except Singaporean public holidays)
8:30 AM – 6:00 PM Singapore Time (SGT)
Tel.
+65 6 513 0488
Fax
+65 6 846 1090
E-mail
[email protected]
Rest of the World
Monday to Friday (except German public holidays)
08:00 – 17:00 Central European Time (CET)
Tel. from Europe
+49 (0) 180 512 42 42
From outside Europe +49 89 4129 13776
Fax
+49 (0) 89 41 29 637 78
E-mail
[email protected]
Headquarters, Plants and Subsidiaries
Headquarters
ROHDE&SCHWARZ GmbH & Co. KG
Mühldorfstraße 15 · D-81671 München
P.O.Box 80 14 69 · D-81614 München
Plants
ROHDE&SCHWARZ Messgerätebau GmbH
Riedbachstraße 58 · D-87700 Memmingen
P.O.Box 16 52 · D-87686 Memmingen
ROHDE&SCHWARZ GmbH & Co. KG
Werk Teisnach
Kaikenrieder Straße 27 · D-94244 Teisnach
P.O.Box 11 49 · D-94240 Teisnach
ROHDE&SCHWARZ závod
Vimperk, s.r.o.
Location Spidrova 49
CZ-38501 Vimperk
ROHDE&SCHWARZ GmbH & Co. KG
Dienstleistungszentrum Köln
Graf-Zeppelin-Straße 18 · D-51147 Köln
P.O.Box 98 02 60 · D-51130 Köln
Subsidiaries
R&S BICK Mobilfunk GmbH
Fritz-Hahne-Str. 7 · D-31848 Bad Münder
P.O.Box 20 02 · D-31844 Bad Münder
ROHDE&SCHWARZ FTK GmbH
Wendenschloßstraße 168, Haus 28
D-12557 Berlin
ROHDE&SCHWARZ SIT GmbH
Am Studio 3
D-12489 Berlin
R&S Systems GmbH
Graf-Zeppelin-Straße 18
D-51147 Köln
GEDIS GmbH
Sophienblatt 100
D-24114 Kiel
HAMEG Instruments GmbH
Industriestraße 6
D-63533 Mainhausen
Locations Worldwide
Please refer to our homepage: www.rohde-schwarz.com
◆Sales Locations
◆Service Locations
◆National Websites
Phone +49 (89) 41 29-0
Fax +49 (89) 41 29-121 64
[email protected]
Phone +49 (83 31) 1 08-0
+49 (83 31) 1 08-1124
[email protected]
Phone +49 (99 23) 8 50-0
Fax +49 (99 23) 8 50-174
[email protected]
Phone +420 (388) 45 21 09
Fax +420 (388) 45 21 13
Phone +49 (22 03) 49-0
Fax +49 (22 03) 49 51-229
[email protected]
[email protected]
Phone +49 (50 42) 9 98-0
Fax +49 (50 42) 9 98-105
[email protected]
Phone +49 (30) 658 91-122
Fax +49 (30) 655 50-221
[email protected]
Phone +49 (30) 658 84-0
Fax +49 (30) 658 84-183
[email protected]
Phone +49 (22 03) 49-5 23 25
Fax +49 (22 03) 49-5 23 36
[email protected]
Phone +49 (431) 600 51-0
Fax +49 (431) 600 51-11
[email protected]
Phone +49 (61 82) 800-0
Fax +49 (61 82) 800-100
[email protected]
Application Range of the R&S UP300/350
Operating Manual, 11/2007
1-35
E-1147.2759.00
1
Introduction
This chapter
Chapter 1 describes the use of the R&S UP300/350, provides information on
functions and supplies tips regarding storage and transportation procedures.
Furthermore, you will find a description on how to proceed in warranty cases.
Further
information
Chapter 2 contains an overview of the R&S UP300/350´s control elements,
indicators, etc.
Chapter 3 describes how to put the instrument into operation.
1.1
Application Range of the R&S UP300/350
Use
The R&S UP300/350 is a two-channel audio analyzer which provides a
large number of functions and measurement features at favourable price.
The R&S UP300/350 is capable of performing standard audio measure-
ments with a high degree of accuracy. The extended frequency range which
stretches beyond the audio range and up to 80 kHz permits a large number
of other T & M applications (e.g. in ultrasonic technology, RFI voltage
analysis, etc.) in addition to classic audio measurements.
The R&S UP300/350 generates and analyzes signals using digital signal
processing. Conversion into the analog signal world is performed by means
of high-end 24 bit D/A and A/D converters. This gives the measurement
features a high level of stability. The R&S UP350 also has digital inputs and
outputs.
Performance
features
The key features are:
Frequency range from DC to 80 kHz
Two-channel generator with separate amplitude, phase and frequency
settings for sinewave signal
Generator generates all signals required for audio measurements:
sinewave, two-tone (DFD and Mod Dist), multi-tone, noise, polarity,
burst sinewave)
Generator sweep with up to 2 function parameters
Intrinsic distortion of 0.0003 % at 1 kHz
Simultaneous numeric display of up to 3 measurement values
Clearly structured, graphical representation of measurement results
FFT up to 16 K
Up to 3 digital filters can be activated
All filters commonly used for audio measurements are predefined
USB interface for remote control and for connecting a USB stick
Operation from a
keypad
All functions and parameters can be set via menus using a keypad and a
rotary knob. Current parameters and operating states are clearly arranged
on a TFT colour display.
Remote control
from a PC
The
R&S UP300/350
is
standardly
equipped
with
a
USB
interface to allow communication with a PC. All functions and parameters
can be set. Using the USB device driver, you can create your own
measurement applications in automatic measurement and test systems.
Operating Manual, 11/2007
1.2
Supplied Accessories
Content
1 power cord Europe
1 country specific power cord (if different from Europe)
1 German/English manual
1.3
Warranty
ATTENTION
Equipment returned or sent in for repair must be packed in the original
packing or in packing with electrostatic and mechanical protection.
Warranty
conditions
The General Terms and Conditions of Rohde & Schwarz shall apply.
Returning a
defective
R&S UP300/350
You will find the addresses of your nearest Rohde & Schwarz's representa-
tive and of the support center at the front of the manual.
Indicating claims
under the warranty
We would also ask you to state clearly if you are making a claim for repairs
under warranty, preferably by including your delivery note. Repair requests
that do not explicitly refer to the warranty will, in the first instance, incur
charges.
If your warranty has expired, we will, of course, repair your R&S UP300/350
in accordance with our general installation and service conditions.
Operating Manual, 11/2007
2-37
E-1147.2759.00
2
Control Elements
2.1
Front View
1
ON/STANDBY switch
2
ON/STANDBY indicator
3
BACK/SYS key
4
ESC/CANCEL key
5
ENTER key
6
Cursor keys 3 / 4
7
Cursor keys 6 / 5
8
Signal output Ch 1 (BNC connector)
9
Signal input Ch 1 (BNC connector)
10
Main menu selection keys
11
Rotary knob
12
Numeric keys
13
Function keys
14
Screen
14
13
12
11
10
1
2
3
4
5
6
7
8
9
Rear View: R&S UP300/350
R&S UP300/350
E-1147.2759.00
2-38
Operating Manual, 11/2007
2.2
Rear View: R&S UP300/350
15
Audio monitoring output (jack)
16
Connector for external USB host
17
Connector for external USB
device
18
AC supply connector
19
AC line fuse
20
AC line switch
21
Connector for external monitor
22
Connector for external keyboard
23
Input/output for external reference
(10 MHz)
24
Reserved
25
Reserved
26
Signal input Ch 2 (BNC connector)
27
Signal output Ch 2 (BNC connector)
24
25
22
21
18
19
20
17
16
26
27
23
15
Rear View: R&S UP350 (Digital Interface)
Operating Manual, 11/2007
2-39
E-1147.2759.00
2.3
Rear View: R&S UP350 (Digital Interface)
28
Reserved
29
Reserved
30
Input/output for external reference
(10 MHz)
31
Digital output S/P DIF
32
Digital input S/P DIF
33
Reserved
34
Optical input TOSLINK
35
Optical output TOSLINK
34
35
33
31
32
28
29
30
Unpacking the R&S UP300/350
R&S UP300/350
E-1147.2759.00
3-40
Operating Manual, 11/2007
3
Putting the R&S UP300/350 into Operation
This chapter
Chapter 3 describes how to put the R&S UP300/350 into operation and
connect an external keyboard.
Further
information
Chapter 2 contains an overview of the R&S UP300/350‘s control elements,
indicators, etc.
Chapter 4, “Getting started”, takes you step-by-step through a number of
simple measurements.
Chapter 7 is an in-depth description of the instrument’s interfaces.
ATTENTION
Before putting the R&S UP300/350 into operation, make the following checks:
Ensure that the ventilation holes are free of obstructions.
Ensure that there are no unsuitable signal voltages connected to the
input.
The R&S UP300/350’s outputs may not be overloaded and correct
polarity must be ensured.
The instrument may be damaged if the above checks are not performed.
3.1
Unpacking the R&S UP300/350
Recommended
procedure
When you unpack the R&S UP300/350, proceed as follows:
1.
Remove the R&S UP300/350 from its packaging and check that the
delivery is complete using the accessory list (Ê 1-36).
2.
Carefully check the R&S UP300/350 for any damage.
3.
If there is damage, immediately contact the carrier who delivered the
instrument. Under these circumstances, it is essential to keep the box, in
which the R&S UP300/350 was transported, and the packaging material.
3.2
Setting up the Instrument
CAUTION
There is a risk of injury from sharp edges and becoming wedged
between the setting lever and the handle.
Always be careful not to injure your fingers when installing the instrument and
adjusting its handles.
Setup instructions
The R&S UP300/350 must be only assembled on a firm, level surface. The
instrument has a carrying handle which is also used for various setup options.
This handle can be moved into any position, depending on the
particular field of application.
Setting up the Instrument
Operating Manual, 11/2007
3-41
E-1147.2759.00
Setting the handle
1.
Place the thumb and two fingers around the side-mounted setting lever
and loosen it with a turning action.
2.
Slide the handle lengthwise while twisting it radially in steps of about 12°.
3.
Close the setting lever by pressing on the outer surface.
CAUTION: There is a risk of injury from sharp edges and becoming
wedged between the setting lever and the handle.
4.
Remove the protective film from the screen glass if necessary.
ATTENTION: Do not use pointed or sharp objects.
Connecting the R&S UP300/350 to the AC Line
R&S UP300/350
E-1147.2759.00
3-42
Operating Manual, 11/2007
3.3
Connecting the R&S UP300/350 to the AC Line
WARNING
Danger of electric shock!
The R&S UP300/350 meets the requirements for Safety Class I according to
DIN EN 61010-1/IEC 61010-1, e. g. all metal parts that can be touched or
accessed without removing the enclosure are connected to the protective
ground of the power supply network.
When connecting the instrument to the AC power supply, always use a power
cable and a socket with earthing contact.
Automatic AC line
voltage detection
When the R&S UP300/350 is connected to the AC line, it automatically sets
itself to the correct voltage (range: AC voltage 100 V to 240 V, AC frequency
50 Hz to 60 Hz). There is no need to set the voltage manually or change the
fuse.
Connecting the
AC line
1.
Use the supplied power cord to connect the R&S UP300/350 to the AC
line.
The power supply connector [18] is at the rear of the instrument.
2.
Connect the power cord to the AC line.
3.4
Switching On the R&S UP300/350
Note: The AC line is still connected to the R&S UP300/350 when the
instrument is in the standby mode.
AC line switch on
the rear panel
The R&S UP300/350 is connected to the AC line via power supply connector
[18]. The AC line switch [20] which isolates the R&S UP300/350 from the AC
line is located next to the power supply connector.
ON/STANDBY
switch on the
front panel
ON operating state
After switching on by means of the AC line switch [20] at the rear panel, the
R&S UP300/350 is in standby mode and the yellow LED [2] comes on. If you
press the ON/STANDBY switch [1], the instrument is switched on and the
green LED [2] comes on.
STANDBY operating state
To switch the R&S UP300/350 over from the operating mode to standby
mode, press the ON/STANDBY switch [1] for approx. 2 seconds. After
switching off the ON/STANDBY switch [1], the yellow LED [2] comes on.
Switching on
the R&S UP300/350
1.
Press the AC line switch [20] on the rear panel in the “I” position.
2.
Press the ON/STANDBY switch [20] on the front panel.
The green LED ON [2] comes on.
Operating Manual, 11/2007
3-43
E-1147.2759.00
3.5
Function Test
ATTENTION
The R&S UP300/350 does not contain any parts the operator can repair. Only
properly qualified technicians are allowed to repair the instrument. When
performing service procedures, follow the requirements of VDE 0701.
Function test
After the R&S UP300/350 has been switched on (Ê 3-42), the green LED ON
[2] on the instrument’s front panel comes on. During booting, the "R&S Smart
Instruments" symbol appears on a blue screen background [14]. Booting the
R&S UP300/350 is completed when the waveform and menu bar (Ê 5-57)
appear.
In error case
If the application display (Ê 5-57) does not appear and the red, or green LED
flash alternately, switch the R&S UP300/350 off and on. In case the error
continues, return the instrument to our service center for checking.
When the red and green LEDs [2] flash alternately, an internal error has been
recognized. Return the instrument to our service center for checking.
3.6
EMC
EMC
requirements
The R&S UP300/350 meets the EMC Directive 89/336/EEC (applied
standards EN 55011 Class B and EN 61326).
To prevent EMI, the R&S UP300/350 may only be operated with its enclosure
closed. Only appropriately shielded signal and control cables may be used.
External units, such as keyboard, printer or monitor that are to be connected
to the R&S UP300/350, must comply with EMC directives.
Notes on the
R&S UP300/350's
interference
In audio engineering, inputs and outputs of test or operating instruments are
usually not referenced to the housing ground, but are rather floating or
balanced (or both). The main reason for this complex circuitry is to separate
hum loops.
The R&S UP300/350 inputs are implemented via BNC connectors; the
reference potential is at the outer conductor. If the input is floating (no
connection to the housing), interference at the input amplifier may occur at
extremely high-frequency RFI field strengths due to demodulation, which can
impair the measurement at low levels. Appropriate grounding measures on
the DUT as well as short line lengths help to reduce interference.
In case of doubt, check the spectrum of the measured signal.
Connecting a DUT
R&S UP300/350
E-1147.2759.00
3-44
Operating Manual, 11/2007
3.7
Connecting a DUT
ATTENTION
The analyzer inputs of the R&S UP300/350 are protected against
overvoltage, but must not be overloaded on a permanent basis (Vrms > 33 V).
If overloaded, the instrument may be damaged, and subsequent malfunctions
cannot be excluded.
Generator output
Via the generator outputs Ch 1 [8] and Ch 2 [27], you can stimulate the DUT
with high-end test signals (Ê 6-98).
Analyzer input
Via the analyzer inputs Ch 1 [9] and Ch 2 [26], you can measure and evaluate
the output signals of your DUT (Ê 6-212).
Audio analysis with
the R&S UP300/350
By combining the generator and the analyzer, the R&S UP300/350 provides
versatile capabilities for audio analysis (Ê 6-259, 6-267, 6-268, 6-272, 6-275).
Connecting an External Keyboard
Operating Manual, 11/2007
3-45
E-1147.2759.00
3.8
Connecting an External Keyboard
ATTENTION
Connect the keyboard only when the R&S UP300/350 is off or in the
STANDBY mode, otherwise malfunctions may occur at a later time.
Use
You can connect an external PC keyboard via the 6-pin PS/2 KEYB
connector [22] on the R&S UP300/350’s rear panel. The keyboard makes it
easier to enter file names. The keyboard allows data entry as well as
operation of the R&S UP300/350.
The keyboard is detected automatically when it is connected.
Key assignment for
operating the
R&S UP300/350
[ F1 ] ... [ F7 ]
[ 0 ] to [ 9 ], [ . ], [ - ]
[ F10 ] ⇐ | ⇒ [ F11 ]
[ A ] ... [ D ]
[ F9 ]
[ Esc ]
[ Ç ], [ È ]
[ Å ], [ Æ ]
[ Enter ]
Connecting a USB Stick
R&S UP300/350
E-1147.2759.00
3-46
Operating Manual, 11/2007
3.9
Connecting a USB Stick
ATTENTION
To ensure that the USB stick is detected by the R&S UP300/350, the stick
must be formatted in the FAT32 file system.
Use
You can connect an external USB stick to the USB device interface [17] at the
rear of the R&S UP300/350. The USB stick is an extension of the internal
memory. You can use it to print into a file on the USB stick or to transfer trace
data to a PC.
Generator and Analyzer Settings
Operating Manual, 11/2007
4-47
E-1147.2759.00
4
Getting Started
This chapter
Chapter 4 uses a number of simple settings to illustrate how to operate the
R&S UP300/350.
For the following example, the initial instrument setting is the default setting
(factory). This is set in the PRESET menu (Ê 6-317). The full default setup is
described in chapter 6.
Further
information
Chapter 5 contains an in-depth explanation of the basic operating steps, for
example selecting menus and setting parameters. The layout of the screen
and the information displayed on the screen are also described.
Chapter 6 describes all the R&S UP300/350‘s menus and the associated
functions in detail.
4.1
Generator and Analyzer Settings
Introduction
In this example, the SINE generator function is set at channel Ch 1 with a
frequency of 960 Hz and at channel Ch 2 with a frequency of 2 kHz. Both
signal amplitudes have the value of Vrms = 1 V. The measurement function
FREQ DC RMS is then set and the measurement result is displayed
graphically with the aid of an FFT analysis. The parameters are set manually.
Generator settings
Perform the following steps:
1.
Reset the R&S UP300/350.
• Press the
key.
• Using the
cursor keys select
from the bottom menu
bar.
• Press the
key.
2.
Set the sine signal in the generator.
• Press the main menu
selection key.
• Using the
cursor keys select
from the bottom menu
bar.
• Press the
key.
• Using the
cursor keys select
from the bottom menu
bar.
Generator and Analyzer Settings
R&S UP300/350
E-1147.2759.00
4-48
Operating Manual, 11/2007
3.
Set the signal frequency to 960 Hz in Ch 1 and to 2 kHz in Ch 2.
• Press the numeric key
to select the channel Ch 1.
• Press the
key.
• Use the numeric keys
to enter the value. Finish the
entry with the
unit key.
• Press the numeric key
to select the channel Ch 2.
• Press the
key.
• Use the numeric key to enter the value
. Finish the entry with the
unit key.
4.
Set the signal amplitude Vrms = 1 V.
• Press the numeric key
to select the channels Ch 1 and Ch 2.
• Stay in the
menu.
• Press the
key.
• Use the numeric key to enter the value
. Finish the entry with the
key.
Analyzer settings
1.
Set the analyzer input to generator.
• Press the main menu
selection key.
• Using the
cursor keys select
from the bottom menu
bar.
• Press the
key.
•
Use the
to select the Gen Meas setting.
Finish the selection procedure with the
key.
2.
Switch on the FREQ, DC, RMS, and FFT measurement functions.
• Using the
cursor keys select
from the bottom menu
bar.
• Press the
key.
• Press the
key.
Generator and Analyzer Settings
Operating Manual, 11/2007
4-49
E-1147.2759.00
Graphical display
1.
Graphical display of the measurement results.
• Press the main menu
selection key.
• Using the
cursor keys select
from the bottom menu
bar.
• Press the
key.
• Use the
to select the Spectrum setting.
Finish the selection procedure with the
key.
The R&S
UP300/350
display
2.
Change the scaling of the X axis in the measurement diagram.
• Using the
cursor keys select
from the bottom menu
bar.
• Press the
key.
• Use the numeric key to enter the value
. Finish the entry with the
key.
The R&S
UP300/350
display
Generator and Analyzer Settings
R&S UP300/350
E-1147.2759.00
4-50
Operating Manual, 11/2007
3.
Position the cursor 1 on trace 2.
• Using the
cursor keys select
from the bottom menu
bar.
• Press the numeric key
to select the channel Ch 2.
• Press the
key.
• Press the
key to switch on the cursor.
• Press the
key.
• Use the
to select the Max setting.
Finish the selection procedure with the
key.
The R&S
UP300/350
display
Full-screen
display
1.
Set the full-screen display.
• Press the main menu
selection key.
• Use the
to move the cursor in little steps.
• Use the
cursor keys to position the cursor on the maximum
value.
The R&S
UP300/350
display
Operating Manual, 11/2007
5-51
E-1147.2759.00
5
Manual Operating Concept
5.1
This chapter
Chapter 5 contains an overview of the R&S UP300/350's basic manual
operating concept. This includes a description of the keypad, screen
layout, menu operation, and how to set parameters. There is an overview of
the menus and functions at the end of this chapter.
Further information
Chapter 6 contains an in-depth description of the menu functions.
Chapter 4 contains a brief introduction which takes you step-by-step through
some simple settings.
Overview of Operating Steps
R&S UP300/350
E-1147.2759.00
5-52
Operating Manual, 11/2007
5.1
Overview of Operating Steps
First hierarchical
level
The R&S UP300/350 is basically operated via hierarchically arranged menus.
The following four main menus are simultaneously available at the first
hierarchical level:
Analyzer
Generator
Graph
System
Using the four keys ANL, GEN, GRAPH, and SYS, you can switch between
these menus. Each menu is called at the position where it has been quitted.
Second hierarchical
level
Within the main menu, the corresponding function menus make up the
second hierarchical level. These functions are on the horizontal softkey bar.
Using the horizontal cursor keys, you can navigate between these functions.
Making Entries from the Keypad
Operating Manual, 11/2007
5-53
E-1147.2759.00
Third hierarchical
level
The parameter menus for each function menu are displayed on the vertical
softkey bar at the third hierarchical level.
Some parameter menus include further submenus (fourth level).
Channel selection
keys
The keys Ch 1, Ch 2, and Ch 1&2 (the numeric keys 1, 2, and 3 are
assigned twice) affect the Analyzer, Generator, and Graph menus. They
control which channel is affected by a setting.
Measurement
control keys
The keys START, SINGLE, and STOP (the numeric keys 4, 5, and 6 are
assigned twice) control the sequence of the measurement functions.
Entry possibilities
Enter a parameter value by using the numeric keypad, rotary knob, or
vertical cursor keys.
5.2
Making Entries from the Keypad
Introduction
The R&S UP300/350 is operated using menus in conjunction with a keypad
and a rotary knob. The keypad comprises the following sections:
Numeric keys [12]
Main menu selection keys [10]
Cursor keys [6, 7]
Function keys [13]
Action keys [4, 5]
BACK/SYS key [3]
Making Entries from the Keypad
R&S UP300/350
E-1147.2759.00
5-54
Operating Manual, 11/2007
5.2.1
Numeric Keys
Function 1
When the entry field is open, the numeric keys are used to enter numeric
parameters.
to
−
Inserts one of the digits “0” to “9” at the cursor position.
−
Inserts a decimal point “.” at the cursor position.
−
Inserts a minus sign “-” at the cursor position.
Function 2
When the entry field is closed, the numeric keys have special functions. The
numeric keys 1, 2, and 3 are used to select the channels, and the numeric
keys 4, 5, and 6 are used to control the measurement.
−
Selects channel Ch 1 for settings and measurements.
−
Selects channel Ch 2 for settings and measurements.
−
Selects both channels (CH 1&2) for settings and measurements.
−
Starts continuous measurement.
−
Starts a single measurement.
−
Stops continuous measurement.
5.2.2
Main Menu Selection Keys
Function
These keys represent the top operator control level and are used to switch
between the Generator menu, Analyzer menu, and Graph menu. The menu
items in the menu section of the display also change accordingly. When
switching between the main menus, the selected menu level is always shown
in its most recent state.
−
Switches to the Analyzer menu.
−
Switches to the Generator menu.
−
Switches to the Graph menu.
−
Displays the measurement diagram in the Graph menu in full-screen
mode (toggle function).
Making Entries from the Keypad
Operating Manual, 11/2007
5-55
E-1147.2759.00
5.2.3
Rotary Knob
Function
As well as the numeric keys and the cursor keys, the rotary knob is also used
to set parameters.
The rotary knob has several functions:
−
Incrementing
(turn
clockwise)
or
decrementing
(turn
counter-clockwise) numerical instrument parameters.
−
Navigating through selection fields upwards (turn clockwise) or down-
wards (turn counter-clockwise).
−
Positioning markers, cursors, etc. on the screen.
5.2.4
Cursor Keys
Function
As well as the numeric keys and the rotary knob, the cursor keys are used for
entering parameters and to navigate through the menus.
The cursor keys have the following functions:
−
Navigating through menus and selection fields
−
The 3or4 cursor keys move to change the position you want within the
numerical editing line. Use the 3or4 cursor keys to move the cursor in
the full screen graph (Ê 6-314).
−
The 6 or 5 cursor keys increment or decrement numerical parameter
entries.
5.2.5
Function Keys
Function
In the function area, various instrument functions are displayed depending on
which menu has been selected.
The displayed instrument functions are assigned to the seven function keys
down the right side of the screen. This means that each function key can
have a variety of functions (Ê 5-60).
When a function key is pressed, various responses can be elicited:
−
Immediate activation of a function or toggling between settings
−
Entry of a value or selection of a setting/function
−
Entry of units
−
Confirmation of a new setting and opening of a new menu item
−
Branching to a submenu
−
Opening and closing a selection field
Making Entries from the Keypad
R&S UP300/350
E-1147.2759.00
5-56
Operating Manual, 11/2007
5.2.6
Action Keys
Function
The action keys are for terminating menu-guided settings.
−
This key is for closing the entry field or selection field after data has
been entered. The new value is set in the R&S UP300/350.
Note: Pressing a unit key will also terminate the entry of the setting data.
−
This key is for closing the entry field or selection field, but the data that
has
been
entered
is
not
saved,
i.e.
the
old
value
is
retained.
5.2.7
BACK/SYS Key
Function 1: BACK
If the entry field is open, the BACK/SYS [3] key can be used to correct
numeric inputs (BACK).
−
If the parameter entry field is open, the key functions as the BACK key
(i.e. a value entered using the keyboard can be deleted again one
character at a time). The key has no effect if the value in the entry field
was changed using the cursor keys or rotary knob.
Function 2: SYS
If the entry field is closed, the BACK/SYS key [3] will open or close the
system menu (SYS).
−
When you press the key, the measurement menu is blanked out and
replaced by the SYS menu. Other functions are assigned to the function
keys [13].
−
By pressing the key again, you can quit the SYS menu and accept the
new settings.
Operating Manual, 11/2007
5-57
E-1147.2759.00
5.3
Screen Display
Introduction
The screen [14] provides on-going information about events and the
parameters associated with the selected setting functions.
The display mode for the parameters, lettering of the function keys, and type
of menu, all depend on the current settings.
Screen layout
The screen is divided into three areas:
I
Display area
II
Menu area
III
Function area
III
I
II
Operating Manual, 11/2007
5.3.1
Display Area
Introduction
The display window of the R&S UP300/350 changes depending on the
selected main menu. In the Analyzer and Generator menus, the currently set
values are displayed in the form of a list. If you select the Graph menu, a
measurement diagram is displayed in the parameter field. With all other main
menus, the measurement values are displayed in the top part of the screen.
Display of menus:
The display window contains:
Parameter list/Measurement diagram (a)
(Ê 6-98, 6-212, 6-286)
Channel display (b)
(Ê 6-115)
Measurement displays/Cursor parameters (c)
(Ê 6-227, 6-300, 6-314)
Status line with error messages (d)
(Ê 6-285, 8-347)
Selection fields that appear on screen (e)
(Ê 5-64)
Entry fields that appear on screen (f)
(Ê 5-65)
Traces (g) (channel Ch 1: green, channel Ch 2: yellow)
(Ê 6-227)
X cursors (i) and Y cursors (h)
(Ê 6-300)
Generator menu
(call with
)
Analyzer menu
(call with
)
a
d
e
c
b
a
f
d
b
Operating Manual, 11/2007
5-59
E-1147.2759.00
Graph menu
(call with
)
Full screen
(call with
)
a
d
c
b
g
i
a
c
h
i
h
g
Operating Manual, 11/2007
5.3.2
Menu Area
Menu display
Menus
for
setting
the
setting
parameters
and
functions
are
displayed in the menu area. The selected menu is highlighted, e. g. Genera-
tor menu.
5.3.3
Function Area
Displaying the
current assignment
When a menu is selected, the associated instrument functions are displayed
in the function area.
The displayed instrument functions are assigned to the seven function keys
down the right-hand side of the screen. If a key in the function area does not
have any lettering, the button cannot be used. Every attempt to press the
button will be ignored. If a key has lettering in grey colour, the key has been
deactivated.
Deactivated key
Hidden key with no meaning
Active key
Calling and Changing the Menus
Operating Manual, 11/2007
5-61
E-1147.2759.00
5.4
Calling and Changing the Menus
Introduction
Operating the R&S UP300/350 is menu-guided. The instrument settings
associated with any menu you select are displayed in the function area.
Pressing a function key has one of the following effects:
Switching functions on/off
Toggling a setting
Opening entries or selection fields
Opening the submenus
The 3 or 4 cursor keys [6] are used for menu navigation.
Calling or
changing menus
1.
Press the main menu
selection key.
2.
Select a menu, e. g.
, with the 3 or 4 cursor keys [6].
The menu name is highlighted and the appropriate function is assigned
to the function keys [13].
3.
Press the
function key in the
menu.The
key will
appear in the function area.
4.
Select the
menu with the 3 or 4 cursor keys [6].
The menu name is highlighted and the appropriate function is assigned
to the function keys [13].
Calling and Changing the Menus
R&S UP300/350
E-1147.2759.00
5-62
Operating Manual, 11/2007
Note: A function key with a double arrow, e. g.
, tells you that pressing
this key will call a submenu.
Calling/Quitting
submenus
1.
Press the
function key in the
menu.
The AVERAGING submenu opens and the new functions are assigned
to the function keys [13].
2.
Press the
function key in the
submenu.
The submenu is closed and the previous functions remain assigned to
the function keys [13].
Setting the Parameters
Operating Manual, 11/2007
5-63
E-1147.2759.00
5.5
Setting the Parameters
Choice
of methods
Parameters can be set in a number of ways:
Direct selection of an instrument function (function key)
Toggling a setting
Selecting settings from selection fields
Entering numerical parameters in entry fields
The numeric keys [12], the main menu selection keys [10], rotary knob [11],
cursor keys [6, 7], function keys [13] and action keys [4, 5] can all be used to
select and enter instrument parameters.
5.5.1
Direct Selection of Instrument Functions
Introduction
When you select a menu, various instrument functions are displayed in the
function area. Some instrument functions can be set directly by pressing a
function key.
Example:
Scaling the X axis
(Ê 6-292)
1.
Press the main menu
selection key.
2.
Select the
menu with the 3 or 4 cursor keys [6].
3.
Press the
function key in the
menu.
The X axis of the measurement diagram is automatically scaled.
5.5.2
Toggling a Setting
Introduction
When a menu is selected, a number of instrument functions will be displayed
in the function area. Some instrument functions can be switched on or off by
a stroke of the function key (toggling).
The function key is highlighted when the instrument function is active.
Example:
Activating/
Deactivating the
channel output Ch 1
(Ê 6-104)
1.
Press the main menu
selection key.
2.
Select the
menu with the 3 or 4cursor keys [6].
3.
Press the numeric key
to select the channel Ch 1.
4.
Press the
function key in the
menu.
The function key is highlighted and the new setting is saved. After
switching on, the output signal with the currently set parameters is
present at the output [8].
5.
To deactivate the channel output Ch 1, press the
function key in
the
menu.
The function key is no longer highlighted and the output signal is no
longer present at the channel output.
Setting the Parameters
R&S UP300/350
E-1147.2759.00
5-64
Operating Manual, 11/2007
5.5.3
Selecting Settings
Introduction
When you select a menu, a number of instrument functions are displayed in
the function area. If certain function keys are then pressed, a selection field is
displayed in the diagram area. You can then choose and activate any of the
settings offered for selection.
The function key you select is highlighted.
Example:
Selecting the
signal coupling
(Ê 6-219)
1.
Press the main menu
selection key.
2.
Select the
menu with the 3 or 4 cursor keys [6].
3.
Press the
function key in the
menu.
A selection field containing the available settings is displayed. The
default setting is “AC“.
4.
Select the signal coupling with the rotary knob [11].
5.
Press the ENTER key [5] to confirm the selection field.
The new value is set and saved and the field will be closed.
If you want to keep the old setting, close the selection field with the
ESC/CANCEL key [4] or press the function key again.
Note: If there are more than 12 options available, a scroll bar is displayed on
the right side of the selection field.
Setting the Parameters
Operating Manual, 11/2007
5-65
E-1147.2759.00
5.5.4
Entering Numerical Parameters
Introduction
When you select a menu, a number of instrument functions will be displayed
in the function area. If you press certain function keys, an entry field will be
displayed in the menu area.
The function key you select is highlighted.
There are two ways of entering numerical parameters:
Entry of a number with the numeric keys
Change of a number with the cursor keys and rotary knob
5.5.4.1
Entry with the Numeric Keys
Example:
Entering a
signal frequency
(Ê 6-116)
1.
Press the main menu
selection key.
2.
Select the
menu with the 3 or 4 cursor keys [6].
3.
Press the
function key in the
menu.
4.
Select the
menu with the 3 or 4 cursor keys [6].
5.
Press the
function key in the
menu.
An entry field containing the current setting is displayed. At the same
time, the function keys are assigned various units of measurement.
Entering
a new value
6.
Overwrite the old value, e. g. with 21.5 kHz, with the numeric keys [12].
Ö
Note: If a numeric key is pressed after the entry field is brought up on the
screen, the old value will be erased. However, a complete new value
must now be entered using the numeric keys.
With the SYS/BACK key [3], a value entered using the keyboard can be
deleted again one character at a time.
Setting the Parameters
R&S UP300/350
E-1147.2759.00
5-66
Operating Manual, 11/2007
Terminating
entries
7.
a) Press the
function key to terminate the entry.
The R&S UP300/350 sets the value that has been set numerically using
the new unit. The entry window is closed.
b) Press the
key [5] to terminate the entry.
The R&S UP300/350 sets the value that has been set numerically, but
with the old unit. The entry window is closed.
Note: If a parameter is unitless or always has the same unit, you can
terminate the entry with the ENTER key.
c) Press the
key [4] to cancel the entry.
The old value is retained. The entry window is closed.
Invalid
parameter entry
If the entered value is outside the permissible range, the largest or smallest
permissible value is coerced and the message “Value is out of range"
appears in the status line.
Using another unit
of measure to
display a value
1.
Press the
function key in the
menu.
An entry field containing the current setting is displayed. At the same
time, the function keys are assigned various units of measurement.
2.
Press the
function key to display the value in Hz.
Ö
The value is displayed using the new unit. The input window is not
closed.
Note: In the parameter list, values from 1 to 999 are displayed in front of the
decimal point. In other words, if the digit sequence <5000> and the unit
are entered, <5.000 kHz> appears in the display.
Setting the Parameters
Operating Manual, 11/2007
5-67
E-1147.2759.00
5.5.4.2
Entry with the Cursor Keys and Rotary Knob
Example:
Entering a signal
frequency
(Ê 6-115)
1.
Press the main menu
selection key.
2.
Select the
menu with the 3 or 4 cursor keys [6].
3.
Press the
function key in the
menu.
4.
Select the
menu with the 3 or 4cursor keys [6].
5.
Press the
function key in the
menu.
An entry field containing the current setting is displayed. At the same
time, the function keys are assigned various units of measurement.
Entering
a new value,
e. g. 1.5 kHz
6.
Using the 3 and 4 cursor keys [6], position the cursor on a decimal
place in the entry field.
3 ×
Ö
7.
a) Press the 6 or 5 cursor keys [7] until you obtain the value you
want.
Pressing the 5 cursor key once increments the value by one; pressing
the 6 cursor key once decrements the value by one.
5 ×
Ö
b) Turn the rotary knob [11] until you obtain the value you want.
Turning clockwise increases the value; turning counter-clockwise
reduces the value.
5 ×
Ö
Note: In both cases, there is a carry associated with incrementation or
decrementation. In other words, if a 9 digit is incremented or a 0 digit
decremented, a carry is added to, or subtracted from the next highest
digit.
Setting the Parameters
R&S UP300/350
E-1147.2759.00
5-68
Operating Manual, 11/2007
Terminating
entries
8.
a) Press the
function key to terminate the entry.
The new unit is displayed and the input window is closed.
b) Press the
key [5] to terminate the entry.
The R&S UP300/350 sets the value that has been set numerically but
with the old unit. The entry window is closed.
Note: If a parameter is unitless or always has the same unit, you can set
and terminate the entry only with the ENTER key.
c) Press the
key [4] to cancel the entry.
The old value is retained. The entry window is closed.
Invalid
parameter entry
If the limit value is reached, the numeric value in the entry window remains
the same and is neither increased nor decreased. No error message is
issued.
Using another unit
of measure to
display a value
1.
Press the
function key in the
menu.
An entry field containing the current setting is displayed. At the same
time, the function keys are assigned various units of measurement.
2.
Press the
function key to display the value in Hz.
Ö
The numerically set value is displayed using the new unit. The input
window is not closed.
Note: In the parameter list, values from 1 to 999 are displayed in front of the
decimal point. In other words, if the digit sequence <5000> and the unit
are entered, <5.000 kHz> appears in the display.
Overview of all Menus and Functions
Operating Manual, 11/2007
5-69
E-1147.2759.00
5.6
Overview of all Menus and Functions
5.6.1
Generator
5.6.1.1
FUNCTIONS Menu
Function key
assignment
Display the next set of functions.
Sinewave signal
(Ê 6-114)
Noise signal
(Ê 6-119)
Multi-sinewave signal
(Ê 6-122)
Sine burst signal
(Ê 6-132)
Two-tone signal for measurement of modulation distortions
(Ê 6-138)
Difference frequency signal
(Ê 6-144)
Display the previous set of functions.
Polarity test signal
(Ê 6-150)
DC voltage component
(Ê 6-152)
Sweeped sinewave signal and measured RMS
(Ê 6-154)
Sweeped sinewave signal and measured RMS Selective
(Ê 6-171)
Sweeped sinewave signal and measured RMS Selective
(Ê 6-190)
5.6.1.2
SINE Menu
Function key
assignment
Activate/Deactivate the frequency coupling of the channels.
(Ê 6-116)
Enter the signal frequency of the active channel.
(Ê 6-115)
Overview of all Menus and Functions
R&S UP300/350
E-1147.2759.00
5-70
Operating Manual, 11/2007
Enter the phase difference between the channels.
(Ê 6-116)
Enter the signal amplitude.
(Ê 6-117)
Enter the reference value.
(Ê 6-118)
5.6.1.3
NOISE Menu
Function key
assignment
Select the amplitude distribution function.
(Ê 6-120)
Enter the signal amplitude.
(Ê 6-120)
Enter the reference value.
(Ê 6-118)
5.6.1.4
MULTISINE Menu
Function key
assignment
Enter the number of sinewave tones.
(Ê 6-123)
Open the submenu:
Configuration of signal parameters
Exit the submenu.
Enter the frequency.
(Ê 6-124)
Enter the start phase.
(Ê 6-125)
Enter the relative signal amplitude.
(Ê 6-125)
Enter the frequency resolution.
(Ê 6-126)
Enter the reference value for the signal.
(Ê 6-128)
Activate/Deactivate amplitude modulation.
(Ê6-129)
Enter the AM frequency.
(Ê 6-130)
Enter the AM modulation depth.
(Ê 6-131)
Overview of all Menus and Functions
Operating Manual, 11/2007
5-71
E-1147.2759.00
5.6.1.5
SINE BURST Menu
Function key
assignment
Enter the signal frequency.
(Ê 6-133)
Enter the high-level time.
(Ê 6-134)
Enter the interval time.
(Ê 6-135)
Enter the high-level amplitude.
(Ê 6-136)
Enter the low-level amplitude.
(Ê 6-137)
Enter the reference value.
(Ê 6-118)
5.6.1.6
MOD DIST Menu
Function key
assignment
Enter the useful signal frequency.
(Ê 6-140)
Enter the interference signal frequency.
(Ê 6-140)
Enter the ratio between interference amplitude and useful amplitude.(Ê 6-142)
Enter the total RMS of the signal.
(Ê 6-143)
Enter the reference value.
(Ê 6-118)
5.6.1.7
DFD Menu
Function key
assignment
Measurement acc. to IEC 118: Enter the upper DFD frequency.
(Ê 6-145)
Measurement acc. to IEC 268: Enter the center frequency.
(Ê 6-145)
Enter the difference frequency.
(Ê 6-145, 6-147)
Enter the total RMS of the signal.
(Ê 6-149)
Overview of all Menus and Functions
R&S UP300/350
E-1147.2759.00
5-72
Operating Manual, 11/2007
Enter the reference value.
(Ê 6-118)
5.6.1.8
POLARITY TEST Menu
Function key
assignment
Enter the signal amplitude.
(Ê 6-151)
Enter the reference value.
(Ê 6-118)
5.6.1.9
DC OFFSET Menu
Function key
assignment
Enter the DC offset.
(Ê 6-153)
Overview of all Menus and Functions
Operating Manual, 11/2007
5-73
E-1147.2759.00
5.6.1.10
SWEEP RMS Menu
Function key
assignment
Select the sweep mode.
(Ê 6-156)
Set the measurement time.
(Ê 6-157)
Open the submenu:
Set the sweep parameters for frequency.
Exit the submenu.
Enter the start value.
(Ê 6-159)
Enter the stop value.
(Ê 6-159)
Select scaling of sweep steps (Lin/Log).
(Ê 6-161)
Enter the number of reading points.
(Ê 6-161)
Enter the step size.
(Ê 6-161)
Enter the measurement delay.
(Ê 6-163)
Open the submenu:
Set the sweep parameters for amplitude.
Exit the submenu.
Enter the start value.
(Ê 6-165)
Enter the stop value.
(Ê 6-165)
Select scaling of sweep steps (Lin/Log).
(Ê 6-161)
Enter the number of reading points.
(Ê 6-167)
Enter the step size.
(Ê 6-167)
Enter the measurement delay.
(Ê 6-168)
Activate/Deactivate the filter.
(Ê 6-232)
Select the unit for the level display.
(Ê 6-169)
Overview of all Menus and Functions
R&S UP300/350
E-1147.2759.00
5-74
Operating Manual, 11/2007
5.6.1.11
SWEEP RMS SELECTIVE Menu
Function key
assignment
Select the sweep mode.
(Ê 6-156)
Select the measurement bandwidth.
(Ê 6-174)
Open the submenu:
Set the sweep parameters for frequency.
Exit the submenu.
Enter the start value.
(Ê 6-159)
Enter the stop value.
(Ê 6-159)
Select scaling of sweep steps (Lin/Log).
(Ê 6-161)
Enter the number of reading points.
(Ê 6-161)
Enter the step size.
(Ê 6-161)
Enter the measurement delay.
(Ê 6-163)
Open the submenu:
Set the sweep parameters for amplitude.
Exit the submenu.
Enter the start value.
(Ê 6-165)
Enter the stop value.
(Ê 6-165)
Select scaling of sweep steps (Lin/Log).
(Ê 6-161)
Enter the number of reading points.
(Ê 6-167)
Enter the step size.
(Ê 6-167)
Enter the measurement delay.
(Ê 6-168)
Activate/Deactivate the filter.
(Ê 6-232)
Select the unit for the level display.
(Ê 6-169)
Overview of all Menus and Functions
Operating Manual, 11/2007
5-75
E-1147.2759.00
5.6.1.12
SWEEP THD Menu
Function key
assignment
Select the sweep mode.
(Ê 6-192)
Select the measurement mode.
(Ê 6-193)
Set the measurement time.
(Ê 6-195)
Open the submenu:
Set the sweep parameters for frequency.
Exit the submenu.
Enter the start value.
(Ê 6-197)
Enter the stop value.
(Ê 6-197)
Select scaling of sweep steps (Lin/Log).
(Ê 6-198)
Enter the number of reading points.
(Ê 6-198)
Enter the step size.
(Ê 6-198)
Enter the measurement delay.
(Ê 6-201)
Open the submenu:
Set the sweep parameters for amplitude.
Exit the submenu.
Enter the start value.
(Ê 6-203)
Enter the stop value.
(Ê 6-203)
Select scaling of sweep steps (Lin/Log).
(Ê 6-205)
Enter the number of reading points.
(Ê 6-206)
Enter the step size.
(Ê 6-206)
Enter the measurement delay.
(Ê 6-207)
Activate/Deactivate the filter.
(Ê 6-232)
Select the unit for the level display.
(Ê 6-208)
Overview of all Menus and Functions
R&S UP300/350
E-1147.2759.00
5-76
Operating Manual, 11/2007
5.6.1.13
MONITOR Menu
Function key
assignment
Switch the audio monitoring output on/off.
(Ê 6-210)
Select the signal source.
(Ê 6-211)
Enter the volume.
(Ê 6-211)
5.6.1.14
CONFIG Menu
Function key
assignment
Select the generator type (digital) (R&S UP350 only).
(Ê 6-101)
Select the bandwidth of the generator.
(Ê 6-102)
Select the reference potential of the output signal.
(Ê 6-103)
Switch the generator output on/off.
(Ê 6-104)
Select the level range switching mode.
(Ê 6-105)
Select the generator type (analog) (R&S UP350 only).
(Ê 6-101)
Select the sample frequency of the output signal (R&S UP350 only). (Ê 6-107)
Enter the offset of the sample frequency (R&S UP350 only).
(Ê 6-108)
Set the validity bit (R&S UP350 only).
(Ê 6-108)
Select the word size of the output signal (R&S UP350 only).
(Ê 6-109)
Select the interface protocol (R&S UP350 only).
(Ê 6-109)
Overview of all Menus and Functions
Operating Manual, 11/2007
5-77
E-1147.2759.00
5.6.2
Analyzer
5.6.2.1
FUNCTIONS Menu
Function key
assignment
Display the next set of functions.
Measure the frequency, DC voltage, and RMS.
(Ê 6-228)
Measure the peak value.
(Ê 6-237)
Measure the quasi-peak value.
(Ê 6-243)
Selective RMS measurement
(Ê 6-246)
Frequency-domain display mode of the input signal
(Ê 6-251)
Measure distortion (THD, THD+N, SINAD, Noise).
(Ê 6-259)
Display the previous set of functions.
Perform the polarity test
(Ê 6-267)
Measure the difference frequency distortion.
(Ê 6-268)
Measure the phase difference between channels Ch 1 and Ch 2.
(Ê 6-272)
Measure modulation distortion.
(Ê 6-275)
Protocol analysis (R&S UP350 only)
(Ê 6-278)
Measure the sample frequency (R&S UP350 only).
(Ê 6-281)
Overview of all Menus and Functions
R&S UP300/350
E-1147.2759.00
5-78
Operating Manual, 11/2007
5.6.2.2
FREQUENCY, DC, RMS Menu
Function key
assignment
Select the measurement time.
(Ê 6-230)
Select the measurement result display.
(Ê 6-232)
(RMS & FREQ, or RMS & DC)
Activate/Deactivate the filter.
(Ê 6-232)
Open the submenu:
Set the averaging mode.
Exit the submenu.
Activate/Deactivate the averaging.
(Ê 6-233)
Enter the averaging factor.
(Ê 6-233)
Select the unit for the level display.
(Ê 6-235)
5.6.2.3
PEAK Menu
Function key
assignment
Select the measurement method.
(Ê 6-239)
Set the interval time.
(Ê 6-240)
Activate/Deactivate the filter.
(Ê 6-232)
Select the unit for the level display.
(Ê 6-241)
Overview of all Menus and Functions
Operating Manual, 11/2007
5-79
E-1147.2759.00
5.6.2.4
QUASI PEAK Menu
Function key
assignment
Select the interval time.
(Ê 6-245)
Activate/Deactivate the filter.
(Ê 6-232)
Select the unit for the level display.
(Ê 6-241)
5.6.2.5
RMS SELECTIVE Menu
Function key
assignment
Select the tuning mode.
(Ê 6-247)
Enter the measurement frequency.
(Ê 6-247)
Select the measurement bandwidth.
(Ê 6-248)
Activate/Deactivate the filter.
(Ê 6-232)
Open the submenu:
(Ê 6-265)
Set the POST FFT.
Exit the submenu.
Activate/Deactivate the FFT.
(Ê 6-266)
Set the FFT size.
(Ê 6-253)
Set the FFT window.
(Ê 6-253)
Select the unit for the level display.
(Ê 6-266)
Overview of all Menus and Functions
R&S UP300/350
E-1147.2759.00
5-80
Operating Manual, 11/2007
5.6.2.6
FFT Menu
Function key
assignment
Set the FFT size.
(Ê 6-253)
Set the FFT window.
(Ê 6-253)
Activate/Deactivate the filter.
(Ê 6-232)
Open the submenu:
Set the averaging mode.
Exit the submenu.
Activate/Deactivate the averaging.
(Ê 6-255)
Enter the averaging factor.
(Ê 6-255)
Select the unit for the level display.
(Ê 6-257)
5.6.2.7
THD Menu
Function key
assignment
Select the measurement mode.
(Ê 6-261)
Select the frequency search mode.
(Ê 6-262)
Select the measurement time.
(Ê 6-264)
Activate/Deactivate the filter.
(Ê 6-232)
Open the submenu:
Set the POST FFT.
Exit the submenu.
Activate/Deactivate the FFT.
(Ê 6-266)
Set the FFT size.
(Ê 6-253)
Set the FFT window.
(Ê 6-253)
Select the unit for the level display.
(Ê 6-266)
Overview of all Menus and Functions
Operating Manual, 11/2007
5-81
E-1147.2759.00
5.6.2.8
DFD Menu
Function key
assignment
Select the difference frequency distortions
(Ê 6-271)
and measurement standard.
Activate/Deactivate the filter.
(Ê 6-232)
Open the submenu:
Set the POST FFT.
Exit the submenu.
Activate/Deactivate the FFT.
(Ê 6-266)
Set the FFT size.
(Ê 6-253)
Set the FFT window.
(Ê 6-253)
Select the unit for the level display.
(Ê 6-266)
5.6.2.9
PHASE Menu
Function key
assignment
Select the type of signal search.
(Ê 6-273)
Overview of all Menus and Functions
R&S UP300/350
E-1147.2759.00
5-82
Operating Manual, 11/2007
5.6.2.10
MOD DIST Menu
Function key
assignment
ActivateDeactivate the filter.
(Ê 6-232)
Open the submenu:
Set the POST FFT.
Exit the submenu.
Activate/Deactivate the FFT.
(Ê 6-266)
Set the FFT size.
(Ê 6-253)
Set the FFT window.
(Ê 6-253)
Select the unit for the level display.
(Ê 6-266)
5.6.2.11
PROTOCOL Menu
Function key
assignment
Enter the measurement time.
(Ê 6-280)
5.6.2.12
SAMPLE RATE Menu
Function key
assignment
Enter the measurement time.
(Ê 6-280)
Overview of all Menus and Functions
Operating Manual, 11/2007
5-83
E-1147.2759.00
5.6.2.13
FILTER Menu
Function key
assignment
Select filter 1.
(Ê 6-283)
Select filter 2.
(Ê 6-283)
Select filter 3.
(Ê 6-283)
5.6.2.14
CONFIG Menu
Function key
assignment
Select the analyzer type (digital).
(Ê 6-215)
Select the bandwidth of the analyzer.
(Ê 6-216)
Select the reference potential of the input signal.
(Ê 6-217)
Select the signal source.
(Ê 6-218)
Select the signal coupling.
(Ê 6-219)
Select the measurement range selection mode.
(Ê 6-220)
Select the measurement channel.
(Ê 6-221)
Select the analyzer type (analog) (R&S UP350).
(Ê 6-215)
Select the sample frequency of the input signal (R&S UP350).
(Ê 6-222)
Select the input (R&S UP350)
(Ê 6-223)
Select the valid number of bits in the input signal (R&S UP350).
(Ê 6-223)
Select the measurement channel.
(Ê 6-221)
Overview of all Menus and Functions
R&S UP300/350
E-1147.2759.00
5-84
Operating Manual, 11/2007
5.6.3
Graph Menu
5.6.3.1
GRAPH MODE Menu
Function key
assignment
Select the display parameters.
(Ê 6-287)
Select the display mode.
(Ê 6-290)
5.6.3.2
X AXIS Menu
Function key
assignment
Activate automatic display area scaling.
(Ê 6-292)
Manual display area scaling:
Enter the upper limit of the display area.
(Ê 6-292)
Manual display area scaling:
Enter the lower limit of the display area.
(Ê 6-292)
Select the display mode.
(Ê 6-299)
5.6.3.3
Y AXIS Menu
Function key
assignment
Activate automatic display area scaling.
(Ê 6-296)
Manual display area scaling:
Enter the upper limit of the display area.
(Ê 6-296)
Manual display area scaling:
Enter the lower limit of the display area.
(Ê 6-296)
Select the display mode.
(Ê 6-299)
Overview of all Menus and Functions
Operating Manual, 11/2007
5-85
E-1147.2759.00
5.6.3.4
CURSORS Menu
Function key
assignment
Open the submenu:
Configure cursor 1 on the X axis.
Exit the submenu.
Activate/Deactivate the cursor.
(Ê 6-302)
Position the cursor manually.
(Ê 6-305)
Assign a cursor to a trace (Ch 1 or Ch 2).
(Ê 6-303)
Zoom the display area.
(Ê 6-307)
Position a cursor on the maximum value.
(Ê 6-303)
Open the submenu:
Configure cursor 2 on the X axis.
Exit the submenu.
Activate/Deactivate the cursor.
(Ê 6-302)
Position the cursor manually.
(Ê 6-305)
Assign a cursor to a trace (Ch 1 or Ch 2).
(Ê 6-303)
Zoom the display area.
(Ê 6-307)
Position the cursor on the maximum value.
(Ê 6-303)
Open the submenu:
Configure cursor 1 on the Y axis.
Exit the submenu.
Activate/Deactivate the cursor.
(Ê 6-310)
Position the cursor manually.
(Ê 6-311)
Zoom the display area.
(Ê 6-312)
Overview of all Menus and Functions
R&S UP300/350
E-1147.2759.00
5-86
Operating Manual, 11/2007
Open the submenu:
Configure cursor 2 on the Y axis.
Exit the submenu.
Activate/Deactivate the cursor.
(Ê 6-310)
Position the cursor manually.
(Ê 6-311)
Zoom the display area.
(Ê 6-312)
Overview of all Menus and Functions
Operating Manual, 11/2007
5-87
E-1147.2759.00
5.6.4
System menu (SYS Menu)
5.6.4.1
PRESET Menu
Function key
assignment
Call the instrument setting.
(Ê 6-318)
Select the instrument setting.
(Ê 6-318)
Start the remote control manually.
(Ê 6-319)
5.6.4.2
STATE Menu
Function key
assignment
Configuration settings of the analyzer and generator.
(Ê 6-320)
5.6.4.3
FILE Menu
Function key
assignment
Save a user-defined setting.
(Ê 6-323)
Load a user-defined setting.
(Ê 6-323)
Print out a screenshot, save the measurement results.
(Ê 6-325)
Overview of all Menus and Functions
R&S UP300/350
E-1147.2759.00
5-88
Operating Manual, 11/2007
5.6.4.4
CONFIG Menu
Function key
assignment
Set the date and time.
(Ê 6-329)
Select an internal or external reference source.
(Ê 6-331)
Configure the instrument interfaces.
(Ê 6-332)
Set the screen saver mode.
(Ê 6-334)
Select an internal or external monitor.
(Ê 6-336)
5.6.4.5
SERVICE Menu
Function key
assignment
Perform a selftest.
(Ê 6-337)
5.6.4.6
INFO Menu
Function key
assignment
Display the module data.
(Ê 6-339)
Display the instrument statistics.
(Ê 6-339)
Display the system messages.
(Ê 6-340)
5.6.4.7
CALIB Menu
Function key
assignment
Perform the automatic calibration.
(Ê 6-341)
Factory Default Settings
Operating Manual, 11/2007
6-89
E-1147.2759.00
6
Working with the R&S UP300/350
This chapter
Chapter 6 fully explains all the functions of the audio analyzer, and the
application of these functions. The menus are described in the same
sequence as the procedure for configuring and producing an output signal:
Factory default settings
Configuration of the generator
Configuration of the analyzer
Graphical display of the measurement results
Further information
The operating concept is explained in chapter 5, which also contains an
overview of the menus and functions.
The index at the end of this manual will also help you find the information you
want.
6.1
Factory Default Settings
Switching on for the
first time
When the R&S UP300/350 (Ê 3-42) is switched on, the settings used when
the instrument was last switched off are restored. When you switch on for the
first time and if the "Factory" setting has been selected as the PRESET
default setting (Ê 6-323), the factory default settings are activated.
Factory Default Settings
R&S UP300/350
E-1147.2759.00
6-90
Operating Manual, 11/2007
6.1.1
Generator
Note: All level parameters of the individual generator functions as well as the
frequency at SINE can be set channel independently (Ch 1, Ch 2). These
parameters are listed in two columns in the table below the “Settings”. The
function parameters applying to both channels (Ch 1&2) are listed in one
column.
Function
Parameter
Settings
Channel Ch 1
Channel Ch 2
f1 = f2
Off
FREQ
1 kHz
1 kHz
AMPL
100 mV (0.1 FS)
100 mV (0.1 FS)
PHASE DIFF.
0 grd
SINE
REF. VALUE
1 mV
1 mV
PDF
Rectangular
AMPL
100 mV (0.1 FS)
100 mV (0.1 FS)
NOISE
REF. VALUE
1 mV
1 mV
NUMBER OF SINE
1
SPACING
100.058 Hz
REF. VALUE
100 mV (0.1 FS)
100 mV (0.1 FS)
AM STATE
Off
AM FREQ
10 Hz
MULTISINE
AM DEPTH
10 %
GEN FREQ
1 kHz
HIGH LEVEL TIME
500 ms
INTERVAL
1 s
HIGH LEVEL AMPL
100 mV (0.1 FS)
100 mV (0.1 FS)
LOW LEVEL AMPL
0
0
SINE BURST
REF. VALUE
1 mV
1 mV
UPPER FREQ
7 kHz
LOWER FREQ
60 Hz
AMPL RATIO
4
4
MOD DIST
TOTAL RMS
100 mV (0.1 FS)
100 mV (0.1 FS)
Factory Default Settings
Operating Manual, 11/2007
6-91
E-1147.2759.00
Function
Parameter
Settings
Channel Ch 1
Channel Ch 2
REF. VALUE
1 mV
1 mV
UPPER FREQ
8.100 kHz
MEAN FREQ
8.000 kHz
DIFF FREQ
200 Hz
TOTAL RMS
100 mV (0.1 FS)
100 mV (0.1 FS)
DFD
REF. VALUE
1 mV
1 mV
PEAK
100 mV (0.1 FS)
100 mV (0.1 FS)
POLARITY TEST
REF. VALUE
1 mV
1 mV
DC OFFSET
DC OFFSET
100 mV (0.1 FS)
100 mV (0.1 FS)
MODE
FREQ SWEEP
MEAS TIME
10 ms
FILTER
Off
UNIT
V (FS)
REF. VALUE
1 mV
PARAM FREQ
START
10 Hz
STOP
22.139 kHz
POINTS
100
STEP SIZE
223.470 Hz
SPACING
Linear
MEAS DELAY
0 s
PARAM AMPL
START
100 mV (0.1 FS)
STOP
7.495 V (0.999 FS)
POINTS
100
STEP SIZE
74.7 mV (0.0998)
SPACING
Linear
SWEEP RMS
MEAS DELAY
200 ms
MODE
FREQ SWEEP
SWEEP RMS Sel.
BANDWIDTH
1/3 octave
Factory Default Settings
R&S UP300/350
E-1147.2759.00
6-92
Operating Manual, 11/2007
Function
Parameter
Settings
Channel Ch 1
Channel Ch 2
FILTER
Off
UNIT
V (FS)
REF. VALUE
1 mV
PARAM FREQ
START
10 Hz
STOP
22.139 kHz
POINTS
100
STEP SIZE
223.470 Hz
SPACING
Linear
MEAS DELAY
0 s
PARAM AMPL
START
100 mV (0.1 FS)
STOP
7.495 V (0.999 FS)
POINTS
100
STEP SIZE
74.7 mV (0.0998)
SPACING
Linear
MEAS DELAY
200 ms
MODE
FREQ SWEEP
MEAS MODE
THD (All.Harm.)
HARMONICS
MEAS TIME
10 ms
FILTER
Off
UNIT
dB
PARAM FREQ
START
10 Hz
STOP
22.139 kHz
POINTS
100
STEP SIZE
223.470 Hz
SPACING
Linear
MEAS DELAY
0 s
PARAM AMPL
START
100 mV (0.1 FS)
STOP
7.495 V (0.999 FS)
SWEEP THD
POINTS
100
Factory Default Settings
Operating Manual, 11/2007
6-93
E-1147.2759.00
Function
Parameter
Settings
Channel Ch 1
Channel Ch 2
STEP SIZE
74.7 mV (0.0998)
SPACING
Linear
MEAS DELAY
200 ms
OUTPUT
Off
SOURCE
Generator
MONITOR
VOLUME
20 %
20 %
BANDWIDTH
22 kHz
COMMON
Floating
Floating
OUTPUT
On
On
CONFIG ANALOG
RANGE MODE
Auto
Auto
SAMPLE RATE
44.1 kHz
FS OFFSET
0 ppm
VALIDITY BIT
valid
NO. OF BITS
24
24
CONFIG DIGITAL
PROTOCOL
Consumer
Factory Default Settings
R&S UP300/350
E-1147.2759.00
6-94
Operating Manual, 11/2007
6.1.2
Analyzer
Note: Some parameters of the analyzer functions (FILTER, CONFIG) can be
set channel independently (Ch 1, Ch 2). These parameters are listed in two
columns in the table below the “Settings”. The function parameters applying
to both channels (Ch 1&2) are listed in one column.
Function
Parameter
Settings
Channel Ch 1
Channel Ch 2
MEAS TIME
Auto fast
FILTER
Off
AVG MODE
Off
AVG FACTOR
1
UNIT Ch1
V (FS)
UNIT Ch2
V (FS)
REF. VALUE Ch1
1 mV (0.001 FS)
RMS DC FREQ
REF. VALUE Ch2
1 mV (0.001 FS)
MEAS MODE
Peak pos
INTERVAL TIME
250 ms
FILTER
Off
AVG MODE
Off
AVG FACTOR
1
UNIT Ch1
V (FS)
UNIT Ch2
V (FS)
REF. VALUE Ch1
1 mV (0.001 FS)
PEAK
REF. VALUE Ch2
1 mV (0.001 FS)
INTERVAL TIME
3 s
FILTER
Off
UNIT Ch1
V (FS)
UNIT Ch2
V (FS)
REF. VALUE Ch1
1 mV (0.001 FS)
QUASI PEAK
REF. VALUE Ch2
1 mV (0.001 FS)
TUNING MODE
Auto
CENTER FREQ
1 kHz
RMS SELECTIVE
BANDWIDTH
1/3 octave
Factory Default Settings
Operating Manual, 11/2007
6-95
E-1147.2759.00
Function
Parameter
Settings
Channel Ch 1
Channel Ch 2
FILTER
Off
POST FFT
Off
FFT SIZE
1024
WINDOW TYPE
Rife Vincent 2
UNIT Ch1
V (FS)
UNIT Ch2
V (FS)
REF. VALUE Ch1
1 mV (0.001 FS)
REF. VALUE Ch2
1 mV (0.001 FS)
FFT SIZE
1024
WINDOW TYPE
Rife Vincent 2
FILTER
Off
AVG MODE
Off
AVG FACTOR
1
UNIT
dBV (dBFS)
FFT
REF. VALUE
1 mV
MEAS MODE
THD (All Harm.)
HARMONICS
FREQ MODE
Auto
MEAS TIME
Fast
FILTER
Off
POST FFT
Off
FFT SIZE
1024
WINDOW TYPE
Rife Vincent 2
THD
UNIT
dB
POLARITY
STATUS
On
MEAS MODE
d2 (IEC 268)
FILTER
Off
POST FFT
Off
FFT SIZE
1024
WINDOW TYPE
Rife Vincent 2
DFD
UNIT
dB
Factory Default Settings
R&S UP300/350
E-1147.2759.00
6-96
Operating Manual, 11/2007
Function
Parameter
Settings
Channel Ch 1
Channel Ch 2
MEAS MODE
Auto tuning
PHASE
FREQ
1 kHz
FILTER
Off
POST FFT
Off
FFT SIZE
1024
WINDOW TYPE
Rife Vincent 2
MOD DIST
UNIT
dB
PROTOCOL
MEAS TIME
100 ms
SAMPLE RATE
MEAS TIME
100 ms
FILTER NO. 1
Off
Off
FILTER NO. 2
Off
Off
FILTER
FILTER NO. 3
Off
Off
BANDWIDTH
22 kHz
COMMON
Floating
Floating
INPUT
On
On
COUPLING
AC
RANGE MODE
Auto
Auto
CONFIG ANALOG
CHANNEL
Ch 1&2
SAMPLE RATE
44.1 kHz
INPUT
S/P DIF
NO. OF BITS
24
24
CONFIG DIGITAL
CHANNEL
Ch 1&2
Factory Default Settings
Operating Manual, 11/2007
6-97
E-1147.2759.00
6.1.3
Graph
Function
Parameter
Settings
GRAPH TYPE
Spectrum
GRAPH MODE
GRAPH MODE
Overwrite
X AXIS
AUTO SCALING
(MAX,MIN,LOG)
On
Y AXIS
AUTO SCALING
(MAX,MIN,LOG)
On
X1, X2,
STATUS
Off
POSITION
-
LOCK TO
PLOT
Ch1&2
ZOOM
-
FIND
-
Y1,Y2
STATUS
Off
POSITION
-
CURSORS
ZOOM
-
6.1.4
System
Function
Parameter
Settings
PRESET
PRESET
FACTORY
FILE
PRINT
HP DeskJet mono
REFERENCE
Intern
USB MASTER
AUTO
CONFIG
MONITOR
Intern
Operating Manual, 11/2007
6.2
Generator
Introduction
The generator is used to generate all the signals required for the audio
measurements. These signal functions can be generated in an analog or
digital form (R&S UP350 only). Acoustic analysis of the output signal is pos-
sible at the audio monitoring output.
Activating the
Generator menu
1. The instrument has to be in local mode.
2. Close the SYS menu if opened.
3. Close every entry field if opened.
4. Press the main menu
selection key.
The Generator menu is displayed:
Menus for
configuring and
setting output
parameters
The menus used to set the generator functions are displayed in the menu
area (Ê 6-112).
Select the signal functions.
(Ê 6-110)
Reservation for parameter menu of the 1st activated function
Reservation for parameter menu of the 2nd activated function
Reservation for parameter menu of the 3rd activated function
Configure the monitor output.
(Ê 6-209)
Configure the output parameters.
(Ê 6-99)
Operating Manual, 11/2007
6-99
E-1147.2759.00
6.2.1
Configuring Generator Parameters (CONFIG)
Description
The CONFIG menu is used for basic configuration of the generator. The
following settings are made in the CONFIG menu:
Switchover between the analog and digital generator (R&S UP350 only)
Configuration of parameters for digital interface (R&S UP350 only)
Switchover between bandwidths (sample rate)
Activation/Deactivation of analog generator output
Configuration of output
Selection of range switching and setting of level range
Selecting the
CONFIG Menu
Use the 3 or 4 cursor keys to select the
menu.
The menu name is highlighted and the function keys [13] are assigned
the appropriate function.
Analog generator
Function key
assignment
Select the generator type (digital) (R&S UP350 only).
(Ê 6-101)
Select the bandwidth of the generator.
(Ê 6-102)
Select the reference potential of the output signal.
(Ê 6-103)
Switch the generator output on/off.
(Ê 6-104)
Select the level range switching mode.
(Ê 6-105)
Operating Manual, 11/2007
Digital generator
(R&S UP350 only)
Function key
assignment
Select the generator type (analog).
(Ê 6-101)
Select the sample frequency of the output signal.
(Ê 6-107)
Enter the sample frequency offset.
(Ê 6-108)
Set the validity bit.
(Ê 6-108)
Select the valid number of bits in the input signal.
(Ê 6-109)
Select the interface protocol.
(Ê 6-109)
