Response CWK5 Installation And Operating Instructions Manual

CCTV Kit CWK5 Installation and Operating Instructions These instructions should be retained in a safe place for future reference. ...

4 3 DVR FEATURES 5 4 PHYSICAL UNIT 6 4.1 Front Panel 6 4.1.1 DVR Button Functions 6 4.2 Rear Panel 8 5 HARDWARE SETUP 9 5.1 Hard Disk Drive Installation 9 5.2 Monitor Connection 9 5.3 Camera Installation and Connection 9 5.3.1 Installation 10 Dome Cameras 10 Heavy Duty Cameras 11 5.3.2 Connection 13 5.4 Mouse Connection 13 5.5 DVR Power Connection 14 6 SETUP 15 A. Set up using the DVR Front Panel 15 B. Set up using the Mou ...

The Response Wired Internal Dome Cameras are colour, day cameras. The cameras easily connect to your DVR for the protection of your home or office, etc. The heavy duty cameras are easily mounted on walls and the internal dome cameras on ceilings using the supplied mounting brackets and bases. The Response 4 Channel DVR provides a total video security ...

(with a 160GB hard drive unit fitted in the drawer) 2 x Wired Heavy Duty Colour Cameras 2 x Wired Internal Dome Colour Cameras 2 x 10m camera extension cable 2 x 20m camera extension cable 1 x Power adaptor and power cord 1 x 1 to 5 way power splitter cable assembly 1 x Video output to monitor cable (1m) 4 x Camera fixings kits - wall plugs and screws, Including allen key tool for adjusting camera head positi ...

●PAL/NTSC operation ●160GB installed hard drive unit ●High quality colour Video at 50fps or 60fps recording/playback ●Recording speed: PAL max. 50fps (quad); NTSC max. 60fps (quad) ●Recording mode: continuous, motion detection, time schedule ●123 hours continuous recording at 25fps with the 160GB hard drive. (for only x 1 channel recording) ●Recording and compress ...

●LED Lights: (a) GREEN (PWR): The DVR unit is powered up and running. (b) RED (HDD): System is recording or in playback mode. ●Hard Drive Drawer Lock 4.1.1 DVR Button Functions: A series of buttons on the DVR front panel allow the system to operate its basic functions, such as recording, playback, fast-forward, rewind, etc. For more details about the DVR menu, refer to “6. SETUP”. – CH1 Use this button ...

If you push this button, the DVR will display all 4 channels (cameras) at the same time in quad screen. – ●(REC) Press “REC” button to start manual recording. You will then see a red dot ‘●’ on the selected channel on the screen, which means that the channel is now recording. To stop manual recording, press “REC” again during recording mode. ...

To change the menu field, use the up “” or down “” buttons. – SEL Use this button to change values on main menu or sub menu setting. Also use this button to increase values when adjusting parameters. 4.2 Rear Panel ●USB PORT Use this port to backup video on to a USB stick for transferring on to a PC. ●PS/2 MOUSE PORT Use this port for PS/2 mouse connection. ●VIDEO INPUT Use these BNC ports (CH1 to CH4) to connect cameras ...

Note: Only read if you wish to replace/upgrade the existing supplied 160GB hard drive unit fitted in the DVR. 1. Unlock the front hard drive drawer using the key supplied. 2. Pull the drawer’s lever to remove the drawer from the DVR. 3. Remove the x 4 screws on the base of the drawer which secure the hard drive in place to remove the existing unit. 4. Replace with the new hard drive unit, refit ...

The Response Dome Camera is only suitable for internal use and should not be installed outside. It is also recommended to install the cables for the dome camera in the ceiling and passed down the wall through a cable conduit. 1. Unscrew the rim part of the dome cover from its base as shown below. Once the cover is removed, take care not to touch any of the exposed electronic circuitry to avoid any possible d ...

the tilt and panning positions of the camera lens as shown (Fig. 3). 6. Refit the cover of the camera on to its base. 7. If the position of the camera needs further adjusting after the system is powered up, ensure the power is isolated from the cameras when removing the cover again to prevent the risk of any shock. Heavy Duty Cameras Installation 1. Use the cameras main ...

reduce the chances of it being tampered with. 2. Screw the post bracket to the main housing and tighten the nut until secure (Fig. 5). Now pass the Cameras video/power lead through the main bracket and then secure the lower part of the post on to the main bracket (Fig. 6). Feed the video/power leads through the hole in the wall, starting with the largest connector, and th ...

the video extension cable(s) supplied. If any additional camera(s) have an extension cable with a RCA male plug then use one of the supplied BNC to RCA adaptors to convert to a BNC type for connection to the DVR. Use the 5 way splitter cable assembly already connected to the DVR’s power adaptor to power each camera (operating on 12VDC voltage onl ...

Connect the power adaptor's output plug into the DVR to power the DVR. Connect the power adaptor’s mains lead into the adaptor and plug into the mains (240VAC) wall socket and switch ON. The DVR will boot up. The screen shown in Fig. 5.01 will be displayed during boot up. After the system has booted up, the DVR will display the monitor in quad mode. Fig. 5.01 ...

advised to format the hard drive first. Please refer to Section 6.5, pages 22-23. The system includes a login window, and there are three password levels in the system, including admin (highest), operator, and guest (lowest), Fig. 6.01. If the user does not login to the system, the user can only view live video display. When the user is logged in ...

After the system has booted-up, click the right mouse button and the login window will appear. Move the cursor to “Account”, and click the left mouse button and input the correct account by moving the cursor over the correct numbers/characters and left clicking the mouse button to select them. Select “Password” and input the correct password. Finally select “Login” to enter the system. There is one factory- preset logi ...

Move to the “Display” option to enable or disable the screen display of each camera. Modify the camera name of each channel (Figs. 6.04 and 6.05). 6.2 Record This section allows the user to set the DVR to record over timed periods and via motion detection. (Note: If at any time you wish to start manually recording then press the “REC ●” button once on the D ...

Change the record frame rate for each channel - see Fig. 6.07. The higher the record frame rate, the more natural movement you will see in playback. Independent setting for each channel is possible. For PAL video output format, the system default value is 12 frames per second for each channel. The system will record 48 frames per second with all channels. The user can set frame rate as 3 ~ 25 frames per second with each channel ...

Move the cursor to 24 and press [QUAD] button in the DVR front panel, or left click the mouse button on the time period 24. - Grey bar: No recording will be made for this time period unless the user activates manual recording. - Red bar: The time period with a red bar will activate continuous recording mode (Time record) unless there is any manual stopping during tha ...

This sets the recording duration (in seconds) after motion recording is activated. Selection values are “05, 10, 15, 20, 25, 30” (in seconds). 6.3.3 [MOTION DETECTION] [CHANNEL] Select the channel (1, 2, 3, 4) for recording by motion detection (Fig. 6.10). [SENSITIVITY] This adjusts the sensitivity of the built-in motion sensor on the DVR system while recording. The lower the number, the higher the sensitivity is. Values ...