Miele KM 3010 Operating And Installation Instructions

Gas hobs To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr. 09 168 420

and in these operating and installation instructions. It is, however, set up for connection to the gas and electricity supplies in the countries specified. For trouble-free operation of the appliance, it is best to use it in the countries spe- cified for use. For use in other countries, please contact Miele in your country.

Turn off the gas emergency control valve immediately. This is usually located near the gas meter. Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. Do not operate electrical lights or switches, i.e. do not switch them “On” or “Off”. Open all doors and windows to ventilate the area. If the smell of gas persists, evacuate the building. In the UK you must now: Call the Gas Emergency Contact Centre (Tel: 0 800 111 999). For any gas work in the UK always use a Gas Safe registered engineer. In other countries please follow relevant country specific procedures on gas.

Caring for the environment ................................................................................  16 Guide to the appliance........................................................................................  17 Hob........................................................................................................................ 17 KM 3010........................................................................................................... 17 KM 3014........................................................................................................... 18 Control knobs........................................................................................................ 19 Burner.................................................................................................................... 20 Accessories supplied ............................................................................................ 21 Before using for the first time ............................................................................  22 Cleaning the hob for the first time......................................................................... 22 Switching on the hob for the first time .................................................................. 22 Pans ......................................................................................................................  23 Tips on saving energy ........................................................................................  25 Operation..............................................................................................................  26 Switching on.......................................................................................................... 26 Adjusting the flame................................................................................................ 27 Switching off.......................................................................................................... 27 Safety features.....................................................................................................  28 Thermo-electric flame failure monitor ................................................................... 28 Cleaning and care ...............................................................................................  29 Ceramic surface .................................................................................................... 30 Pan supports ......................................................................................................... 31 Control knobs........................................................................................................ 31 Burner.................................................................................................................... 31 Problem solving guide ........................................................................................  34 Optional accessories ..........................................................................................  36 Burner ratings......................................................................................................  37 After sales service...............................................................................................  38 Contact in case of malfunction ............................................................................. 38 Data plate .............................................................................................................. 38 Warranty ................................................................................................................ 38

Safety distances.................................................................................................... 40 Installation notes ................................................................................................... 43 Building-in dimensions ......................................................................................... 44 KM 3010........................................................................................................... 44 KM 3014........................................................................................................... 45 Installation ............................................................................................................. 46 Gas connection ..................................................................................................... 48 Electrical connection............................................................................................. 51 Converting to another gas type .........................................................................  53 Jet table................................................................................................................. 53 Changing the jets .................................................................................................. 53 Changing the main jets..................................................................................... 53 Changing the small jets.................................................................................... 54 Functional check ................................................................................................... 55 Product data sheets ...........................................................................................  56

6 This hob complies with all relevant local and national safety re- quirements. Inappropriate use can, however, lead to personal in- jury and material damage. Read the operating and installation instructions carefully before using the hob. They contain important information on safety, in- stallation, use and maintenance. This prevents both personal injury and damage to the hob. In accordance with standard IEC 60335-1, Miele expressly and strongly advises that you read and follow the instructions in the chapter on installing the hob as well as the safety instructions and warnings. Miele cannot be held liable for injury or damage caused by non- compliance with these instructions. Keep these instructions in a safe place and pass them on to any future owner.

7 Correct application  This hob is intended for domestic use and use in other similar en- vironments.  This hob is not intended for outdoor use.  It is intended for domestic use only to cook food and keep it warm. Any other use is not supported by the manufacturer and could be dangerous.  This hob is not intended for use by people with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision and instruction concerning its use by a person responsible for their safety. They may only use the hob unsupervised if they have been shown how to use it in a safe way. They must be able to recognise and understand the dangers of misuse.

8 Safety with children  Children under 8 years of age must be kept away from the hob unless they are constantly supervised.  Children over 8 years of age may use the hob without supervision if its operation has been clearly explained to them and they are able to use it safely. Children must be able to understand and recognise the possible dangers caused by incorrect operation.  Children must not be allowed to clean the hob unsupervised.  Please supervise children in the vicinity of the hob and do not let them play with it.  The hob gets hot when in use and remains hot for a while after be- ing switched off. Keep children well away from the hob until it has cooled down and there is no danger of burning.  Danger of burning! Do not store anything which might arouse a child's interest in storage areas above or behind the hob. Otherwise they could be tempted into climbing onto the appliance with the risk of burning themselves.  Risk of burning and scalding. Place pots and pans on the cooking zone in such a way that children cannot pull them down and burn themselves.  Danger of suffocation! Whilst playing, children may become en- tangled in packaging material (such as plastic wrapping) or pull it over their head with the risk of suffocation. Keep packaging material away from children.

9 Technical safety  Unauthorised installation, maintenance and repairs can cause considerable danger for the user. Installation, maintenance and re- pairs must only be carried out by a Miele authorised technician.  Damage to the hob can compromise your safety. Check the hob for visible signs of damage. Do not use the hob if it is damaged.  Reliable and safe operation of this hob can only be assured if it has been connected to the mains electricity supply.  The electrical safety of this hob can only be guaranteed when cor- rectly earthed. It is essential that this standard safety requirement is met. If in any doubt please have the electrical installation tested by a qualified electrician.  To avoid the risk of damage to the hob, make sure that the con- nection data on the data plate (voltage and frequency) match the mains electricity supply before connecting it to the mains. Consult a qualified electrician if in doubt.  Do not connect the hob to the mains electrical supply by a multi- socket adapter or extension lead. These are a fire hazard and do not guarantee the required safety of the appliance.  For safety reasons, this hob may only be used after it has been built in.  This hob must not be used in a non-stationary location (e.g. on a ship).  Never open the casing of the hob. Touching or tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults.  While the hob is under warranty, repairs should only be under- taken by a Miele authorised service technician. Otherwise the war- ranty is invalidated.

10  Miele can only guarantee the safety of the appliance when genu- ine original Miele replacement parts are used. Faulty components must only be replaced by Miele spare parts.  The hob is not intended for use with an external timer switch or a remote control system.  The connection to the gas supply must be carried out by a suit- ably qualified gas fitter, e.g. a Gas Safe registered technician in the UK (see “Gas connection”). If the plug has been removed from the connection cable or or the connection cable is not supplied with a plug, the hob must be connected to the electricity supply by a suit- ably qualified electrician (see “Installation – Electrical connection”).  If the mains connection cable is damaged, it must be replaced with a special mains connection cable by a qualified electrician (see “Electrical connection” in the “Installation” chapter).  During installation, maintenance and repair work, the hob must be disconnected from the mains electricity supply. The gas supply must also be shut off. Depending on country this is done in one of several different ways: – the mains fuse has been disconnected, or – the screw-out fuse is removed (in countries where this is applic- able), or – switch off at the wall socket and withdraw the plug from the socket. Pull by the plug and not by the mains connection cable to disconnect from the mains electricity supply. – the gas inlet valve is closed.  Danger of electric shock! Do not use the hob if it is faulty, or if the ceramic surface is cracked, chipped or damaged in any way. Switch it off immediately. Discon- nect it from the mains electricity and gas supply. Call Service.

11  If the hob is installed behind a cabinet door, do not close the door while the hob is in use. Heat and moisture can build up behind the closed door. This can result in damage to the hob, the housing unit and the floor. Leave the furniture door open until the hob has cooled down completely.

12 Correct use  The hob gets hot when in use and remains hot for some time after being switched off. Do not touch the hob if there is a possibility that it could still be hot.  Due to the high temperatures radiated, objects left near the hob when it is in use could catch fire. Do not use the hob to heat up the room.  Oil and fat can overheat and catch fire. Do not leave the hob unat- tended when cooking with oil and fat. If it does ignite do not attempt to put the flames out with water. Disconnect the hob from the mains and use a suitable fire blanket, saucepan lid, damp towel or similar to smother the flames.  Flames could set the grease filters of a cooker hood on fire. Do not flambé under a cooker hood.  Spray canisters, aerosols and other inflammable substances can ignite when heated. Therefore do not store such items or substances in a drawer under the hob. Cutlery inserts must be heat-resistant.  Do not heat an empty pan.  Do not heat up food in closed containers e.g. tins or sealed jars on the hob, as pressure can build up in the container, causing it to explode.  Do not cover the hob, e.g. with a hob cover, a cloth or protective foil. The material could catch fire, shatter or melt if the hob is switched on by mistake or if residual heat is still present.  If the appliance is switched on by mistake, or if there is residual heat present, there is the risk of any metal items placed on the hob heating up. Other materials can melt or catch fire. Do not use the ap- pliance as a resting place for anything.

13  You could burn yourself on the hot hob. Protect your hands with heat-resistant pot holders or gloves when handling hot pots and pans. Do not let them get wet or damp, as this causes heat to trans- fer through the material more quickly with the risk of scalding or burning yourself on steam. Be sure to keep all textiles away from the gas flames. Do not use oversized cloths, tea towels or other similar materials.  When using an electrical appliance, e.g. a hand-held food blender, near the hob, ensure that the cable of the electrical appliance cannot come into contact with the hot hob. The insulation on the cable could become damaged.  Even a light object can cause damage in certain circumstances. Do not drop anything on the ceramic surface.  Plastic and aluminium foil containers melt at high temperatures. Do not use plastic or aluminium foil containers on the hob.  When a control knob is pressed down, a spark is generated on the ignitor. Do not press down the control knob while you are cleaning or touching the hob or a burner in the vicinity of an ignitor.  If a cooker hood is installed above the hob, ensure that the burn- ers are always covered with a pan when in use. Otherwise flames could reach the cooker hood, parts of which could then be damaged or even set on fire.  Only light the gas burners after all burner parts have been properly assembled.  Pans must be the correct size for the burner they are used on (see “Suitable Pans”). A pan which is too small will be unstable on the pan support. If the pan diameter is too large, flames can spread out to the sides and damage or burn the worktop, wall claddings or sur- rounding units and also parts of the hob. Miele cannot be held liable for this type of damage.

14  Ensure that the flames from the burner do not spread out beyond the base and up the sides of the pan.  Do not use pans with very thin bases on this hob, and never heat up empty pans as they could get damaged. This could also damage the appliance.  The pan support supplied with the appliance must always be used. Never place a pan on the burner itself.  Replace the pan supports carefully to avoid scratching the surface of the hob.  Do not use or store flammable materials near this hob.  Remove splashes of fat and other food debris from the surface of the hob as soon as possible. These are a fire hazard.  Using the hob will cause a build-up of heat and moisture in the room in which it is installed. Ensure that the room has sufficient nat- ural or mechanical means of ventilation, e.g. a cooker hood.  If the hob is used for very long periods of time, additional ventila- tion of the room may be necessary, e.g. by opening windows or doors, or running the cooker hood on the highest setting.  Do not use roasting dishes, pans or grilling stones that are large enough to cover more than one burner. The resulting build-up of heat could damage the hob.  If the hob has not been used for a long period of time it should be thoroughly cleaned before it is used again. It is also advisable to have the appliance tested by a qualified person for safety.

15 Cleaning and care  Do not use a steam cleaning appliance to clean this hob. The steam could reach electrical components and cause a short cir- cuit.

16 Disposal of the packing mater- ial The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Recycling the packaging reduces the use of raw materials in the manufactur- ing process and also reduces the amount of waste in landfill sites. Disposing of your old appli- ance Electrical and electronic appliances of- ten contain valuable materials. They also contain specific materials, com- pounds and components, which were essential for their correct function and safety. These could be hazardous to hu- man health and to the environment if disposed of with your domestic waste or if handled incorrectly. Please do not, therefore, dispose of your old appliance with your household waste. Please dispose of it at your local com- munity waste collection / recycling centre for electrical and electronic ap- pliances, or contact your dealer or Miele for advice. You are also respons- ible for deleting any personal data that may be stored on the appliance being disposed of. Please ensure that your old appliance poses no risk to children while being stored prior to disposal.

17 Hob KM 3010 a Large burner b Small burner c Medium burner d Medium burner e Pan support (one for each burner) f Cooking zone symbols Controls knobs for the cooking zones: g Front right h Rear right i Rear left j Front left

18 KM 3014 a Wok burner b Small burner c Medium burner d Pan support (one for each burner) e Cooking zone symbols Controls knobs for the cooking zones: f Front right g Rear right h Left

19 Control knobs Small/Medium/Large burners Symbol Description  Burner off, the gas supply is turned off  Largest flame  Smallest flame Wok burner Symbol Description  Burner off, the gas supply is turned off  Largest flame: inner and outer burner on highest setting.  Large flame: outer burner on lowest setting, inner burner on highest setting.  Small flame: outer burner off, inner burner on highest setting.  Smallest flame: outer burner off, inner burner on lowest setting.

20 Burner Wok burner a Outer burner cap b Inner burner cap c Burner head d Burner base e Thermocouple f Ignitor Small, medium and large burners a Burner cap b Burner head c Burner base d Thermocouple e Ignitor

21 Accessories supplied The accessories supplied with your ap- pliance as well as a range of optional ones are available to order from Miele (see “Optional accessories”). Accessories supplied with KM 3014 only: Wok ring The wok ring supplied gives additional stability to the wok, especially to woks with a rounded base. Combination trivet The combination trivet supplied must be used if you are using pans with a smaller base diameter than that spe- cified in the chart for suitable pans.

22 Please stick the extra data plate for the appliance supplied with this doc- umentation in the space provided in the “After sales service” section of this booklet. Remove any protective wrapping and stickers. Cleaning the hob for the first time Before using for the first time, clean the hob with a damp cloth only and then wipe dry. Clean all removable parts of the burn- ers with a solution of warm water and a small amount of washing-up liquid applied with a soft sponge. Dry all parts thoroughly after cleaning and then reassemble the burners (see “Cleaning and care”). Switching on the hob for the first time The metal components have a protect- ive coating which when heated for the first time will give off a slight smell and possibly some vapours. The smell and any vapours given off do not indicate a faulty connection or ap- pliance and they are not hazardous to health.

Burner Ø cm Small burner 10 Medium burner 12 Large burner 14 Wok burner 14 Maximum diameter at top of pan Burner Ø cm Small burner 20 Medium burner 22 Large burner 24 Wok burner 26 – Select the pan to suit the size of the burner: large diameter = large burner small diameter = small burner. – Observe the dimensions given in the chart. Using pans that are too large can cause the flames to spread out and damage the surrounding worktop or other appliances. Using pans of the correct size improves efficiency. Pans that are smaller than the pot rests and pans that do not stand safely (without wobbling) on the pot rests are dangerous and should not be used. – In contrast to pans for use on electric hobs, the bases of pans for use on gas hobs do not need to be flat to achieve good results. – Remember when purchasing new pans that manufacturers usually refer to the diameter at the top of the pan in their documentation, and not to the base diameter. – You can use any cookware that is heat-resistant. – Cookware with a thick base is prefer- able as the heat is distributed evenly. With thinner based cookware, there is the risk that food will overheat in places. Therefore it should be stirred more frequently. – Always place the cookware on the pot rests supplied. Do not place cookware directly on the burners. – Place the cookware on the pot rests in such a way that it cannot tip over. A minor wobble can never be com- pletely excluded. – Do not use pots or pans with an edge-supported base. Wok ring Use the wok ring supplied to give ad- ditional stability to pans, especially to woks with a rounded base.

port so that it sits securely in position and cannot move (see diagram). The wok is unique among cookware in that it has a small base diameter and a large rim diameter (usually 35-40 cm). Wok pans are ideal for use on the wok burner. Combination trivet The combination trivet must be used if you wish to use a pan with a smaller diameter base than the minimum given in the table.

25 – Use a pan lid whenever possible to minimize heat loss. – Wide, shallow pans are preferable to tall, narrow ones. They will heat up faster. – Cook with as little water as possible. – Reduce the size of the flame once the water has come to the boil or the oil is hot enough to fry in. – Use a pressure cooker to reduce cooking times.

Unattended food can overheat and catch alight. Do not leave the hob unattended whilst it is being used. Switching on Press in the relevant rotary control and turn it anticlockwise to the large flame symbol. The ignition electrode will “click” and ignite the gas. When the rotary control is operated, a spark is automatically produced on all burners. This is normal and does not indicate a fault. When a flame is visible, keep the rotary control pressed down for 5– 10 seconds, and then let it go. If the burner does not ignite, turn the rotary control to the  position. Ventil- ate the room or wait for at least 1 minute before trying again. When making another ignition attempt, it may be necessary to hold the rotary control for longer. If the burner does not ignite the second time, turn the rotary control back to the  position and see “Prob- lem solving guide”. Switching on during a power outage If there is an interruption to the electri- city supply, the gas can be ignited manually, e.g. with a match. Press in the relevant control and turn it anti-clockwise to the large flame symbol. Hold the control pressed in and light the gas at the burner with a match. Keep the control pressed in for a fur- ther 5-10 seconds and then release it.

The burners can be regulated at any level between the strongest and weak- est flame. As the outer part of the flame is much hotter than the centre, the tips of the flames should stay beneath the pan base. Flame tips which extend beyond the sides of the pan merely warm up the air in the room and can also dam- age pan handles and increase the danger of injury. Adjust the flame so that it does not spread out beyond the sides of the pan. Wok burner Depending on the type of control knob, there may be a stopper between the low and high settings at the 6 o'clock position. Press the control knob down lightly to move past this resistance. Switching off Turn the rotary control clockwise to the  position. The gas supply is cut off and the flame goes out.

monitor Your hob is equipped with a thermo- electric flame failure monitor. If a gas flame is extinguished, e.g. by food boil- ing over or by a draught, the gas supply is switched off. This prevents the re- lease of gas. If you turn the rotary con- trol to the  position, the burner is ready for use again. The thermo-electric flame failure mon- itor operates independently from the electricity supply. This means that it will still work if the hob is used during a power cut.

29 Danger of burning due to hot surfaces. The hob surface, pan supports and burners will be hot after use. Allow the hob to cool down before cleaning it. Risk of damage due to moisture ingress. The steam from a steam cleaning ap- pliance could reach live electrical components and cause a short cir- cuit. Do not use a steam cleaner to clean the hob. All surfaces could be discoloured or damaged if unsuitable cleaning agents are used. All surfaces are susceptible to scratching. Remove all cleaning agent residues immediately. Never use abrasive sponges or cleaning agents. Food boiling over can cause discol- oration of the burner components. Remove any soiling and salt and sugar splashes immediately. When a control knob is pressed down, a spark is generated on the ig- nitor. Do not press down the control knob while you are cleaning or touching the hob or a burner in the vicinity of an ignitor. Unsuitable cleaning agents To avoid damaging the surfaces of the appliance, do not use: – cleaning agents containing soda, al- kalines, ammonia, acids or chlorides – cleaning agents containing descaling agents – stain and rust removers – abrasive cleaning agents, e.g. powder cleaners and cream cleaners – solvent-based cleaning agents – dishwasher cleaner – oven sprays – glass cleaning agents – hard, abrasive brushes or sponges (e.g. pot scourers), or sponges which have been previously used and still contain abrasive cleaning agents – melamine eraser blocks

30 The entire hob should be cleaned after each use. Soften any stubborn soiling before- hand. Dry the hob thoroughly after every damp cleaning to avoid limescale residue. Ceramic surface Risk of damage by pointed ob- jects. The seal between the hob and the worktop could suffer damage. The seal between the ceramic sur- face and the frame could suffer dam- age. Do not use pointed objects for clean- ing. Not all soiling and residues can be removed using a solution of wash- ing-up liquid. An invisible film can develop that can lead to discoloura- tion of the glass ceramic surface. This discolouration cannot be re- moved. Clean the ceramic surface regularly with a proprietary ceramic glass cleaning agent. Remove any coarse soiling with a damp cloth and more stubborn soil- ing with a shielded scraper blade suitable for use on glass. Then clean the ceramic glass surface with the Miele ceramic and stainless steel hob cleaner (see “optional ac- cessories”) or with a proprietary ceramic glass cleaner applied with kitchen paper or a clean cloth. Do not apply cleaner whilst the hob is still hot, as this could result in marking. Please follow the cleaning agent manufacturer's instructions. Spots caused by limescale or water can be removed using Miele's ceramic and stainless steel hob cleaner. Wipe the surface afterwards with a damp cloth to remove any cleaning agent residues. Residues can burn on the next time the appliance is used and cause dam- age to the ceramic surface. Ensure that all cleaning agent residues are re- moved. Dry the ceramic surface with a clean, soft cloth.

31 Pan supports Remove the pan supports. Clean the pan supports in the dish- washer or with a solution of warm water and a little washing-up liquid applied with a soft sponge. Stubborn soiling should be soaked first. After cleaning, dry the pan supports thoroughly with a clean cloth. Control knobs The control knobs are not dish- washer-safe. The control knobs should only be cleaned by hand. The rotary controls can become dis- coloured if they are not cleaned reg- ularly. Clean the control knobs after each use. Clean the control knobs using a solu- tion of warm water and a little wash- ing-up liquid applied with a soft sponge. Burner Do not clean any parts of the burners in a dishwasher. The surface of the burner cap will be- come duller with time. This is com- pletely normal and does not indicate material deterioration. The burner should be dismantled and then cleaned by hand using a solu- tion of warm water and a little wash- ing-up liquid applied with a soft sponge. Clean any soiling from the flame openings. Danger of explosion. Blocked flame openings can cause a dangerous build-up of gas in the base of the hob which could ignite and cause an explosion. This can lead to damage to the appliance and injury. Ensure the flame openings are kept clean at all times. Parts of the burner that cannot be re- moved should be wiped clean with a damp cloth only. The ignitor and thermocouple should be very carefully wiped clean using a well wrung-out cloth. The ignitor must not get wet, other- wise it will not spark. Finally dry everything thoroughly with a clean cloth. Make sure that the flame openings are completely dry.

32 The surface of the burner cap will be- come duller with time. This is com- pletely normal and does not indicate material deterioration. Assembling the small, medium and large burners Place the burner head  on the burner base  so that the thermo- couple  and the ignitor  extend through their respective holes in the burner head. The burner head must click into place correctly. Place the burner cap  flat over the burner head . When correctly posi- tioned, the burner cap will not slide about. Ensure parts are reassembled in the correct order.

33 Assembling the wok burner Place the burner head  on the burner base  so that the thermo- couple  and the ignitor  extend through their respective holes in the burner head. The burner head must click into place correctly. Then place the burner caps  and  in position. Ensure parts are reassembled in the correct order.

34 Many malfunctions and faults that can occur in daily operation can be easily remedied. Time and money will be saved because a service call will not be needed. The following guide may help you to find the reason for a malfunction or a fault, and to correct it. Problem Cause and remedy The burners do not ig- nite when the hob is be- ing used for the first time or after it has been out of use for a longer period. There could be an air lock in the gas pipe. You may need to make several attempts before the burner ignites successfully. The burner does not light after several at- tempts. There is a technical fault. Turn all of the controls clockwise to the  position and interrupt the power supply to the hob for a few seconds. The burner is not correctly assembled. Assemble the burner correctly. The gas shut-off device has not been opened. Open the gas shut-off device. The burner is wet and/or dirty. Clean and dry the burner. The flame openings are blocked and/or wet. Clean and dry the flame openings. The gas flame goes out after ignition. The flames do not touch the thermocouple and the burner does not get hot enough: The burner parts are not positioned correctly. Assemble the burner components correctly. The thermocouple is dirty. Remove any soiling. The flame suddenly looks different. The burner parts are not positioned correctly. Position the burner parts correctly. The burner head or the holes in the burner cap are dirty. Remove any soiling. The gas flame goes out during use. The burner parts are not positioned correctly. Position the burner parts correctly.

35 Problem Cause and remedy The electronic ignition device on the burner is not working. The mains fuse has tripped. If necessary, contact a qualified electrician or Miele Service for assistance. There is food residue stuck between the ignitor and the burner cap. The thermocouple is dirty. Remove any soiling (See “Cleaning and care”).

useful accessories as well as cleaning and conditioning products for your Miele appliances. These products can be ordered through the Miele Webshop. They can also be ordered from Miele (see end of this booklet for contact de- tails) or from your Miele dealer. Ceramic and stainless steel hob cleaner 250 ml Removes heavy soiling, limescale de- posits and aluminium residues Microfibre cloth Removes finger marks and light soiling

Liquid gas 1.0 0.95 – 69 0.25 0.2 Medium burner Natural gas H Liquid gas 1.7 1.7 – 124 0.3 0.35 Large burner Natural gas H Liquid gas 2.7 2.55 – 186 0.5 0.6 Wok Natural gas H Liquid gas 4.7 4.6 – 335 0.3 0.25 KM 3010 Total Natural gas H Liquid gas 7.1 6.9 – 503 KM 3014 Total Natural gas H Liquid gas 7.4 7.25 – 528

38 Contact in case of malfunction In the event of any faults which you cannot remedy yourself, please contact your Miele Dealer or Miele Service. Contact information for Miele Service can be found at the end of this document. Please note that telephone calls may be monitored and recorded for training pur- poses and that a call-out charge will be applied to service visits where the problem could have been resolved as described in this booklet. Please quote the model and serial number of your appliance when contacting Miele. This information can be found on the data plate. Data plate Stick the extra data plate supplied with the appliance here. Make sure that the model number matches the one specified on the back cover of this document. Warranty For information on the appliance warranty specific to your country please contact Miele. See back cover for address. In the UK, your appliance warranty is valid for 2 years from the date of purchase. However, you must activate your cover by calling 0330 160 6640 or registering on- line at www.miele.co.uk.

Damage from falling objects. Take care not to damage the hob when fitting wall units or a cooker hood above it. Fit the wall units and the cooker hood before the hob.  The room in which the hob is installed must conform to all relevant local and national building regulations and safety regulations.  The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort. Any backmoulds must be of heat-resistant material.  The hob must not be installed over a fridge, fridge-freezer, freezer, dishwasher, washing machine, washer-dryer or tumble dryer.  A gas hob must not be installed directly next to a deep fat fryer as the gas flames could ignite the fat in the fryer. It is essential to main- tain a distance of at least 300 mm between these two appliances.  When installing the hob, make sure that the gas pipe and elec- trical connection cable cannot come into contact with hot appliance parts.  The electrical cable and any flexible gas connection pipes must be installed in such a way so that they do not come into contact with any moving kitchen parts (e.g. a drawer), and cannot become trapped.  Observe carefully the safety clearances listed on the following pages.

A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood or if any flammable objects (e.g. utensil rails, wall units etc) are installed above the hob a minimum safety distance of at least 760 mm must be maintained between them and the appliance below. When two or more appliances which have different safety distances are installed together below a cooker hood, you should observe the greatest safety distance.

back of the hob Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear or a tall unit or wall on one side (right or left) (see illus- trations).  Minimum distance between the back of the worktop cut-out and the rear edge of the worktop: 50 mm  Minimum distance between the worktop cut-out and a wall or tall unit to the right of it: 150 mm.  Minimum distance between the worktop cut-out and a wall or tall unit to the left of it: 150 mm. Not allowed Highly recommended Not recommended Not recommended

niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.g. wood) a minimum safety distance  of 50 mm must be maintained between the cut-out and the cladding. If the niche cladding is made from a non-combustible material (e.g. metal, natural stone, ceramic tiles) the minimum safety distance  between the cut-out and the cladding will be 50 mm less the thickness of the cladding. Example: 15 mm niche cladding 50 mm - 15 mm = minimum safety distance of 35 mm Flush-fitted hobs Hob with frame or bevelled edge a Masonry b Niche cladding dimension x = thickness of the niche cladding material c Worktop d Worktop cut-out e Minimum distance to combustible materials 50 mm non-combustible materials 50 mm - dimension x

top Damage caused by incorrect in- stallation. Using sealant under the hob could result in damage to the hob and the worktop if the hob ever needs to be removed for servicing. Do not use sealant between the hob and the worktop. The sealing strip under the edge of the hob provides a sufficient seal for the worktop. Tiled worktops Grout lines  and the hatched area un- derneath the hob frame must be smooth and even. If they are not the hob will not sit flush with the worktop and the sealing strip underneath the hob will not provide a good seal between the hob and the worktop.

KM 3010 a Front b Casing depth c Mains connection box with mains connection cable, L = 2000 mm d Gas connection R ¹/₂ - ISO 7-1 (DIN EN 10226)

c Mains connection box with mains connection cable, L = 2000 mm d Gas connection R ¹/₂ - ISO 7-1 (DIN EN 10226)

Stick the supplied sealing strip under the edge of the hob. Feed the power cable for the hob down through the worktop cut-out. Place the hob loosely in the cut-out. When doing this, make sure that the seal of the appliance sits flush with the worktop on all sides. This is im- portant to ensure an effective seal all round. If the seal does not sit flush with the worktop in the corners, the corner ra- dius (≤ R4) can be carefully cut to fit using a jigsaw. Do not use any additional sealant (e.g. silicone) on the hob. Connect the hob to the electricity supply. Connect the hob to the gas supply (see “Installation – Gas connection”). Preparing the worktop Create the worktop cut-out as shown in the hob diagram. Remember to maintain the minimum safety dis- tances (see “Installation – Safety dis- tances”). Seal any cut surfaces on wooden worktops with a special varnish, silic- one sealant or resin to prevent the wood from swelling as a result of moisture ingress. The sealant must be heat-resistant. Make sure that the sealant does not come into contact with the top of the worktop. The seal under the appliance ensures that the hob will sit securely in the cut- out without slipping. Any gap between the appliance frame and worktop will become smaller over time.

Secure the hob using the brackets  supplied. Functional check After installing the hob, ignite all burners to check that they are operat- ing correctly: – The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting. – On the highest setting, the flame must have a distinctive and visible core.

use a Gas Safe registered engineer. Risk of explosion due to an in- correct gas connection. If the gas connection is carried out incorrectly, it may result in gas leak- age. Connection to the gas supply must only be undertaken by an approved and registered gas installer (GasSafe in the UK) in strict accordance with current local and national safety and building regulations. The installer is responsible for ensuring that the ap- pliance functions correctly when in- stalled. Risk of explosion due to an in- correct conversion. If the conversion to another type of gas is carried out incorrectly, it may result in gas leakage. Conversion from one type of gas to another must only be undertaken by an approved and registered gas in- staller in strict accordance with cur- rent local and national safety and building regulations (GasSafe in the UK). The installer is responsible for ensuring that the appliance functions correctly when installed. The gas connection must be in- stalled so that connection can be made either from inside or outside the kitchen furniture unit. The isolat- ing valve must be easily accessible and visible (by opening the cabinet door if necessary). Check with your local gas supplier about the type of gas supplied and compare this information with the type of gas quoted on the appli- ance's data plate. The hob is not connected to an ex- haust flue. When installing and connecting the appliance please observe all relevant installation instructions and ensure it has adequate ventilation once in- stalled. The gas connection must be made in accordance with national and local regulations (GasSafe in the UK). Any special local conditions relating to gas installations as well as build- ing regulations must also be ob- served.

Gas connections, pipes and connec- tion cables can suffer damage if ex- posed to heat from the hob. After installation make sure that neither the gas pipe nor the mains cable can come into contact with hot parts of the appliance and that the gas pipe and connections on the hob cannot come into contact with hot gas exhaust. Risk of explosion due to dam- aged gas pipes. Gas can leak from damaged flexible gas pipes. Attach flexible gas pipes in such a way so that they do not come into contact with any moving kitchen parts (e.g. a drawer) and are not ex- posed to mechanical stress. Connect the hob to the gas supply in accordance with national and local regulations. Check the gas connec- tion for any leaks. This hob is a class 3 appliance and is suitable for use with natural gas or li- quid gas. Category in acc. with EN 30 United Kingdom, Ireland II2H3+ 20, 28–30/37 mbar Depending on country of destination this appliance is set up for connection to natural or liquid gas. See adhesive la- bel on the appliance. Depending on country of destination, jets are supplied for conversion to a dif- ferent type of gas. If the appropriate jets have not been supplied with the appli- ance, you will need to contact Miele. Conversion to another type of gas is described in the section “Converting to another type of gas”. Connecting the hob The hob is supplied with a conical ¹/₂" gas connection point. There are two connection options: – Fixed connection – Flexible connection in accordance with DIN 3383 Part 1, maximum length 2000  mm. (Not for the UK.) Risk of explosion due to gas leakage. Unsuitable sealant will not ensure the required leak protection for connec- tions. Ensure that a suitable sealant is used.

a Connection R ¹/₂" with test point - ISO 7-1 (DIN EN 10226) b 90° elbow The installation height in the area of the gas connection is increased by approx. 60 mm.

by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK). Connection must be made via a switched socket. This will make it easier for service technicians should the appliance need to be re- paired. The electrical socket must be easily accessible after installation. Danger of injury. Miele cannot be held liable for unau- thorised installation, maintenance and repair work as this can be dan- gerous to users. Miele cannot be held liable for dam- age or injury caused by incorrect in- stallation, maintenance or repair work, or by an inadequate or faulty earthing system (e.g. electric shock). If the plug is removed from the con- nection cable or if the cable is sup- plied without a plug, the appliance must be connected to the electrical supply by a suitably qualified electri- cian. If the switched socket is not access- ible after installation, or if the appli- ance is to be hard-wired, an addi- tional means of disconnection must be provided for all poles. When switched off, there must be an all- pole contact gap of at least 3 mm in the switch (including switch, fuses and relays). Connection data is shown on the data plate. It must match the mains electrical supply. After installation ensure that all elec- trical components are shielded and cannot be accessed by users. Total power rating See data plate Connection data The connection data is quoted on the data plate. Please ensure these match the household mains supply. Residual current device For extra safety, it is advisable to pro- tect the appliance with a suitable resid- ual current device (RCD) with a trip range of 30 mA. WARNING THIS APPLIANCE MUST BE EARTHED

Risk of electric shock. There is a risk of electric shock if the appliance is connected to the mains supply during repair or service work. After disconnection, ensure the ap- pliance cannot be switched back on by mistake. To disconnect the appliance from the mains power supply, do one of the fol- lowing depending on installation: Safety fuses Completely remove fuses. Automatic circuit breakers Press the (red) test button until the middle (black) button springs out. Built-in circuit breakers Circuit breakers at least type B or C: Switch the lever from 1 (on) to 0 (off). Residual current device (RCD) Switch the main switch from 1 (on) to 0 (off) or press the test button. Replacing the mains connection cable Risk of electric shock. Incorrect connection to the power supply may result in an electric shock. The mains cable must only be re- placed by a qualified electrician. When replacing the mains cable only use cable type H 05 VV-F with a suit- able cross section. A suitable connec- tion cable is available to order from Miele.

* I N S T A L L A T I O N * 53 Risk of explosion due to an in- correct conversion. If the conversion to another type of gas is carried out incorrectly, it may result in gas leakage. Conversion from one type of gas to another must only be undertaken by an approved and registered gas in- staller in strict accordance with cur- rent local and national safety and building regulations (GasSafe in the UK). The installer is responsible for ensuring that the appliance functions correctly when installed. When converting to another type of gas, both the main and small jets need to be changed. Jet table The jet markings refer to a ¹/₁₀₀ mm bore diameter.  Main jet Small jet Natural gas H Small burner Medium burner Large burner Wok burner 0.76 0.94 1.20 2x 1.07 / 0.72 0.39 0.42 0.54 0.42 Liquid gas Small burner Medium burner Large burner Wok burner 0.52 0.66 0.81 2x 0.70 / 0.46 0.23 0.36 0.42 0.25 Changing the jets Disconnect the hob from the electri- city supply and turn off the gas sup- ply. Changing the main jets Small, medium and large burners Remove the pan support, burner cap  and burner head . Using an M7 socket spanner, un- screw the main jet  Fit the correct jets securely (see jet table). Secure the jets against inadvertent loosening with sealing wax.

* I N S T A L L A T I O N * 54 Wok burner Remove burner caps  and burner head . Using an M7 socket spanner, un- screw the main jets . Fit the correct jets securely (see jet table). Secure the jets against inadvertent loosening with sealing wax. Changing the small jets To change the small jets, the burner fixing screws must first be loosened and the upper section of the appliance removed. Pull the control knobs off. Remove the burner components. Lift the top of the appliance off (see il- lustration). Using a small screwdriver, unscrew the small jet  in the gas fitting. Pull out the jet with a pair of pliers. Fit the correct jets securely (see jet table). Secure the jets against inadvertent loosening with sealing wax.

* I N S T A L L A T I O N * 55 Functional check Check all gas fittings for leaks. Reassemble the hob. Ignite all burners to check that they are operating correctly. – The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting. – On the highest setting, the flame must have a distinctive and visible core. Adhere the label supplied with the jets, stating the type of gas being used.

56 The following data sheets apply to the models described in this operating instruc- tion manual. Information for domestic gas-fired hobs In acc. with regulation (EU) No. 66/2014 MIELE Model name / identifier KM 3010 Number of gas burners 4 Energy efficiency per gas burner (EEgas burner) 1. = 58,2 3. = 55,1 4. = 55,1 Energy efficiency for the gas hob calculated per kg (EEgas hob) 56,1 Information for domestic gas-fired hobs In acc. with regulation (EU) No. 66/2014 MIELE Model name / identifier KM 3014 Number of gas burners 3 Energy efficiency per gas burner (EEgas burner) 1. = 52,4 2. = 55,1 Energy efficiency for the gas hob calculated per kg (EEgas hob) 53,8

Fairacres, Marcham Road Abingdon, Oxon, OX14 1TW Tel: 0330 160 6600 Internet: www.miele.com Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield, VIC 3180 Tel: 1300 464 353 Internet: www.miele.com.au Miele (Shanghai) Trading Ltd. 1-3 Floor, No. 82 Shi Men Yi Road Jing' an District 200040 Shanghai, PRC Tel: +86 21 6157 3500 Fax: +86 21 6157 3511 E-mail: [email protected], Internet: www.miele.cn China 41/F - 4101, Manhattan Place 23 Wang Tai Road Kowloon Bay, Hong Kong Tel: (852) 2610 1025 Fax: (852) 3579 1404 Email: [email protected] Website: www.miele.hk Miele (Hong Kong) Limited Miele India Pvt. Ltd. Ground Floor Copia Corporate Suites Plot No. 9, Jasola New Delhi - 110025 Tel: 011-46 900 000 Fax: 011-46 900 001 E-mail: [email protected] Internet: www.miele.in India Miele Ireland Ltd. 2024 Bianconi Avenue Citywest Business Campus Dublin 24 Tel: (01) 461 07 10 Fax: (01) 461 07 97 E-Mail: [email protected] Internet: www.miele.ie Ireland Malaysia Miele Sdn Bhd Suite 12-2, Level 12 Menara Sapura Kencana Petroleum Solaris Dutamas No. 1 Jalan Dutamas 1 50480 Kuala Lumpur, Malaysia Phone: +603-6209-0288 Fax: +603-6205-3768 Miele New Zealand Limited IRD 98 463 631 Level 2, 10 College Hill Freemans Bay, Auckland 1011 New Zealand Tel: 0800 464 353 Internet: www.miele.co.nz New Zealand Miele Pte. Ltd. 163 Penang Road # 04 - 03 Winsland House II Singapore 238463 Tel: +65 6735 1191 Fax: +65 6735 1161 E-Mail: [email protected] Internet: www.miele.sg Singapore Miele (Pty) Ltd 63 Peter Place, Bryanston 2194 P.O. Box 69434, Bryanston 2021 Tel: (011) 875 9000 Fax: (011) 875 9035 E-mail: [email protected] Internet: www.miele.co.za South Africa Miele Appliances Ltd. Showroom 1 Eiffel 1 Building P.O. Box 114782 - Dubai Tel. +971 4 3044 999 Fax. +971 4 3418 852 800-MIELE (64353) E-Mail: [email protected] Website: www.miele.ae United Arab Emirates Manufacturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany K.E. & Kingstone Co., Ltd. 6th Fl., No. 120, Sec. 2 Jianguo N. Rd. Taipei, Taiwan TEL: +886 2 2502-7256 FAX: +886 2 2502-3077 E-mail: [email protected] Website: www.kenk.com.tw/ke/miele Taiwan Thailand BHIRAJ TOWER at EmQuartier 43rd Floor Unit 4301-4303 689 Sukhumvit Road North Klongton Sub-District Vadhana District Bangkok 10110, Thailand Sheikh Zayed Road, Umm Al Sheif