Matrix S-DRIVE PERFORMANCE TRAINER Manual 

Text of Matrix S-DRIVE PERFORMANCE TRAINER Manual 

2 3 ENGLISH 12 DEUTSCH 21 NEDERALANDS 30 DANSK 39 FRANÇAIS 48 ESPAÑOL 57 ITALIANO 66 ΕΛΛΗΝΙΚΆ 75 POLSKI 84 PORTUGUÊS

Matrix S-DRIVE PERFORMANCE TRAINER SAVE THESE INSTRUCTIONS

• When using a treadmill, basic precautions should always be followed, including the following: Read all instructions before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions. • This product is intended for commercial use. To ensure your safety and protect the equipment, read all instructions befor

SERIAL NUMBER LOCATION

ASSEMBLY UNPACKING Unpack the equipment where you will be using it. Place the carton on a level flat surface. It is recommended that you place a protective covering on your floor. Never open box when it is on its side. IMPORTANT NOTES During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded. Several parts have been pre-lubricated to aid in assembly and usage. Please do not wipe this off. If you

Black Hardware Bags (x2)

Description Qty A B Bolt Flat Washer 4 4 Note: Do not fully tighten hardware until the end of step 5. Step 2 Torque Value: 78.4 Nm / 57.8 ft-lb 2 Note: There are no screws holding on the motor cover. ENGLISH

Red Hardware Bags (x2)

Description Qty C Bolt 4 Note: Do not fully tighten hardware until the end of step 5. Step 3 Torque Value: 78.4 Nm / 57.8 ft-lb White Hardware Bag Description Qty D Bolt 4 Note: Do not fully tighten hardware until the end of step 5. Step 4 Torque Value: 39.2 Nm / 28.9 ft-lb ENGLISH

Yellow Hardware Bag

Description Qty H Screw 2 5 6 Green Hardware Bag Description Qty E F G Bolt Flat Washer Bolt 4 4 2 Note: Step 5 Torque Value: 39.2 Nm / 28.9 ft-lb A. Carefully pull the CABLE (1) through the RIGHT HANDLEBAR SUPPORT using the twist tie located inside the RIGHT HANDLEBAR SUPPORT and attach to the CONNECTOR CABLE (2) on the MAIN FRAME. B. Repeat on other side. C. Completely tighten hardware from steps 2–5 according to th

BEFORE YOU BEGIN

TREADMILL LOCATION Place the treadmill on a level and stable surface away from direct sunlight. The intense UV light can cause discoloration on the plastics. Locate your treadmill in an area with cool temperatures and low humidity. Please leave a clear zone behind the treadmill that is at least the width of the treadmill and at least 79” (2000 mm) long. This zone must be clear of any obstruction and provide the user a clear exit path f

WALK / SPRINT

PROPER USAGE SLED MODE PROPER USAGE PROPER USAGE The treadmill can be used in two modes; sled or walk/sprint. To use the treadmill in sled mode, remove the harness so the user has access to the upper and lower sled handlebars. To use the treadmill in walk / sprint mode, connect the harness and adjust by using the instructions below. Emergency dismount can be done by grabbing the front or side handlebars and jumping with both feet on the si

Clean entire machine using water and a mild soap

or other Matrix approved solution (cleaning agents should be alcohol and ammonia free). DAILY Check harness for wear and secure connections. DAILY Remove the front cover. Check for debris and clean with a dry cloth or small vacuum nozzle. MONTHLY Lubricate treadmill running deck EVERY 3 MONTHS MAINTENANCE 1. Any and all part removal or replacement must be performed b

BEWAHREN SIE DIESE ANLEITUNG SORGFÄLTIG AUF

• Bei der Nutzung eines Laufbands müssen stets grundlegende Vorsichtsmaßnahmen ergriffen werden, darunter Folgendes: Lesen Sie vor der Nutzung dieses Laufbands alle Anweisungen. Es liegt in der Verantwortung des Eigentümers, sicherzustellen, dass alle Nutzer dieses Laufbands über alle Warnungen und Vorsichtsmaßnahmen informiert werden. • Dieses Produkt ist für den gewerb

Matrix S-DRIVE PERFORMANCE TRAINER ORT DER SERIENNUMMER

MONTAGE AUSPACKEN Packen Sie das Gerät am Aufstellungsort aus. Stellen Sie den Karton auf ebenem Untergrund auf. Es wird empfohlen, dass Sie eine Schutzfolie auf dem Boden auslegen. Öffnen Sie den Karton nicht, wenn dieser auf der Seite liegt. WICHTIGE HINWEISE Stellen Sie während jedes Montageschritts sicher, dass ALLE Muttern und Schrauben eingesteckt und teilweise eingeschraubt sind. Mehrere Teile wurden zur Vereinfachung von

Matrix S-DRIVE PERFORMANCE TRAINER Schwarze Beschlagteilebeutel (x2)

Beschreibung Menge A B Schraube Flache Unterlegschei- be 4 4 Hinweis: Die Beschlagteile erst nach Abschluss von Schritt 5 vollständig festziehen. Drehmomentwert Schritt 2: 78,4 Nm / 57,8 ft-lb 2 Hinweis: Die Motorabdeckung ist nicht durch Schrauben gesichert. DEUTSCH

Rote Beschlagteilebeutel (x2)

Beschreibung Menge C Schraube 4 Hinweis: Die Beschlagteile erst nach Abschluss von Schritt 5 vollständig festziehen. Drehmomentwert Schritt 3: 78,4 Nm / 57,8 ft-lb Weißer Beschlagteilebeutel Beschreibung Menge D Schraube 4 Hinweis: Die Beschlagteile erst nach Abschluss von Schritt 5 vollständig festziehen. Drehmomentwert Schritt 4: 39,2 Nm / 28,9 ft-lb DEUTSCH

Drehmomentwert Schritt 5:

39,2 Nm / 28,9 ft-lb A. Ziehen Sie das KABEL (1) vorsichtig durch die RECHTE HANDGRIFFHALTERUNG; verwenden Sie hierzu den Kabelbinder, der sich in der RECHTEN HANDGRIFFHALTERUNG befindet, und verbinden Sie das Kabel mit dem ANSCHLUSSKABEL (2) am

Matrix Treadmill Owners Instructions: