Matrix SATATYA Professional Series Installation Manual

The Persistent Vision Safety Instructions Cautions Warning These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. • Ensure that the power supply voltage is correct before using the camera. • Avoid placing cables too close to magnetic or high voltage devices, to reduce undesirable image noise. • Do not touch sensor modules with fingers. For cleaning use ‘clean cloth’ and wipe it gently. • Do not mount the camera with the lens facing the sun or bright light to prevent damage to the sensor. • Do not expose the camera to temperatures below or beyond its operating temperature. • Do not mount the camera near a radiator or a heater. • In the use of the product, you must be in strict compliance with the electrical safety regulations of the region and nation. • Do not connect several devices to one power adapter as it may cause over-heating or fire hazard. • If smoke, odour or noise rise from the device, turn off the power at once and unplug the power cable, and contact the nearest service center. • To prevent electrical shock, turn off power supply before making electrical connections.

Things you will Need Contents Accessing Reset Pin and SD card slot Accessing via Web Browser 4 7 8 Camera Variants Installation Network Configuration Installing Mounting Template Mounting the Camera Adjusting the Camera Angle Connecting cables Please read this guide first for correct installation and retain it for future reference. The information in this guide is prevailing at the time of publication. However, Matrix Comsec reserves the right to make changes in product design and specifications without prior notice. Copyright All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Matrix Comsec. Warranty Limited Warranty. Valid only if primary protection is provided, mains supply is within limit and protected, and environment conditions maintained within product specifications. Complete warranty statement is available on our website: www.matrixvideosurveillance.com Technical Specification IP66 Protection Accessory Installation Know your Camera 1. Cable Guide 2. Cable Assembly 3. Base Plate 4. Hole for Mounting 5. Pivot Joint 6. Camera Body 7. Screws for adjusting Camera Angle 8. Sunshield bolt 9. Sunshield 10. Lens (Fixed) The Standard variant consists of 2 connectors: Power Connector and Ethernet connector (POE). The Premium variant consist of 4 connectors: Power Connector, Ethernet Connector (POE), Audio IN and Audio OUT. 1 2 3 5 4 6 8 7 9 10 Know your Camera 5 5 11 11 13 14 4 15 18 19 23 5 Figure 1

Things you will Need Camera Variants The Bullet Cameras are available in two variants; Standard and Premium. Both the variants are available in 5MP with 2.8mm, 4.0mm and 6.0mm fixed focal length. You can capture near and broader view with lens of 2.8mm and 4.0 mm focal length. For example it can be used in ATM and Elevators. With lens of 6.0 mm focal length, far and narrow view can be captured. For example it can be used in corridors or long passage to capture long view. 6 5 Type of Lens Focal Length Fixed 4.0mm 6.0mm MIBR50FL40CWS Premium Standard MIBR50FL60CWS 2.8mm MIBR50FL28CWS MIBR50FL28CWP MIBR50FL40CWP MIBR50FL60CWP Fixed Fixed Ÿ Bullet IP Camera Unit Ÿ Wall Mounting Template Ÿ Wall Mounting Screws with Screw Grip (3 nos.) Ÿ Allen Key Ÿ Cable Accessories for weather proofing • A Power Drill, Screwdriver Set, Pliers, Wire-cutter, Ladder. • Necessary Cabling • A Power Supply with the recommended output voltage of 12V DC. Use an adapter to connect the camera to the power outlet. The respective available variants of Standard and Premium are listed in below table,

network failover and to upload image or clip as a result of event trigger. See page 15 to know how to open the camera and insert the SD card. Step 2: Prepare for Installation Ensure that the necessary cabling to connect the camera to LAN port and Power outlet are in place. The connecting cables from the monitoring site should be ready at the installation site. Step 1: Select a Location Select a suitable location for your camera to enable coverage of the intended surveillance area. The location should preferably be a flat surface, such as a wall or a ceiling. You can install the camera where cables are running through the interior of the wall or ceiling as shown in Figure 2. Else cabling has to be done through POE. Installation 8 7 Step 3: IP66 Protection Accessory Installation 1. By default your camera contains the LAN connector fitted by IP66 protection accessory. 3. Rotate the middle part of IP66 assembly in anticlockwise direction to detach the IP66 accessory from the LAN connector. 2. The IP66 protection assembly consist of tail end, middle part, “IO” ring and LAN connector as shown below. Tail end Middle Part “O”ring LAN Connector Power cable IP66 protection accessory Before you start Please make sure, Ÿ The device in the package is in good condition and all the assembly parts are included. Ÿ All the related equipments are powered-off before installation. Ÿ The wall or ceiling is strong enough to support the weight of camera.

LAN Connector IP66 accessory 4. Loosen the tail end of the IP66 accessory by rotating it in anticlockwise direction. Ethernet cable 5. Insert the ethernet cable from behind. Then tighten the “tail end” by rotating in clockwise direction to its maximum and crimp the RJ45 connector. 10 9 6. Insert male RJ45 connector into female connector part. Then tighten the middle part by rotating in clockwise direction.

Wall Mounting: Figure 3 Ceiling Mounting: Figure 2 12 11 Mounting Template Step 6: Adjusting the Camera Angle Step 5: Mounting the Camera • Stick the Mounting Template on the desired installation surface. • Drill three holes through the markings of the Mounting Template on Wall or Ceiling. • Insert the screw grips in the holes you drilled. • To avoid cable damage, take the Power, Ethernet, Audio IN, Audio OUT, Alarm IN, Alarm OUT cables of the camera through the cable guide on the base plate, see Figure 3. • Align the screw holes on the base plate with those you drilled on the installation surface. • If the cabling is running through the interior of the wall or ceiling behind the installation surface then, drill the hole (20mm approx) on the center of the mounting template through the false ceiling. Before you mount the base plate, pull the cables of the camera through the hole drilled on the installation surface, see Figure 2. • Secure the base plate of the camera on the installation surface with the supplied screws. • Use the Allen Key supplied to you to loosen the socket screws on the pivot joint between the base plate and the camera body. • Tilt the camera body to achieve the desired angle. You can turn the camera upto 360 degrees. • Hold it at the desired angle and tighten the socket screw with the Allen key.

Audio Input cable of the camera. The audio when enabled will be recorded with the video and will be available at the monitoring location. 2. You may connect the Audio Output device such as earphone or speaker to the Audio Output cable of the camera. This will generate audio received from the network. Step 6: Connecting Cables Ethernet 12V DC @2A Audio IN Audio Out Figure 4 Figure 5 • Connect the Ethernet cable to LAN port and Power cable to the 12V DC power supply. • In Premium variants, connect the Audio I/O cables if required. If devices such as Mike and Speaker can be connected to Audio IN and Audio OUT, you may need to connect an external power source if their power requirements are not fulfilled with the camera adapter. LED: CLASS1 (Category RS1) Never look at the transmit laser while the power is on. Never look directly at the fiber ports and the fiber cable ends when they are powered on. Use of controls or adjustment to the performance or procedure other than those specified herein may result in hazardous laser emission.

The IP camera is PoE- compliant, allowing transmission of power and data via a single Ethernet cable connected to PoE switch. If you forget the IP address or login credentials of camera then the camera can be reset to factory default settings using the reset pin. Accessing Reset Pin and SD card slot To access the Reset pin 1. Open the Sunshield by removing the sunshield screw. Sunshield Sunshield Screw 2. Open the front cover by rotating it in the anti-clockwise direction. Front cover 3. Press the Reset switch for minimum 5 sec and release the switch to reset the camera to default settings. Reset Pin Figure 6 Figure 7 Figure 8

recordings. SD Card Slot 18 17 Network Configuration Figure 9 To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then install the software to configure the IP address. Steps to get the IP address • Once the camera is connected to the network, it will automatically be assigned a dynamic IP address by the DHCP server. You can view the assigned IP address through any IP scanner utility. • If DHCP server is unavailable or is not able to provide an IP address then 192.168.1.126 will be set as default IP address. • You can change the IP address and subnet mask of Camera from the Basic Settings page of camera. After Reset or SD card insertion, you may need to set the camera focus and camera angle.

The IP cameras are supported by Microsoft Windows Operating System. Steps: 20 19 192.168.1.126 • Run the web browser as administrator. • In the browser address bar, type the IP address of the camera e.g., 192.168.1.126 and press the Enter key to open the login interface. 192.168.1.124 192.168.1.126 • Enter the User Name and Password. • By default, you can login with User Name as admin, operator or viewer with the password as admin, operator and viewer respectively. • Click on Login. Ÿ The browser will ask you to install ActiveX control. Ÿ Click on Run Add-on to install the plugin. In Internet Explorer you can access the camera with Matrix ActiveX plugin. In other browsers you need to install Quicktime or VLC plugin.

Ÿ Now you can Run the plugin. Ÿ Install the Camera software by clicking on Install. Ÿ The home page of the camera will open and the live view will be displayed. Ÿ The camera configuration can be set from Configuration tab. 2 9 - A u g - 2 0 1 9 0 3 : 2 9 : 1 5 P M a a a a a 3 9 3 9

Technical Specification 24 23 Specification Standard Premium Storage NAS SD Card Zoom IVA Events Software Environmental Yes Yes(upto 128GB) ONVIF Profile Operating Temp. Humidity Motion, Temper, Trip Wire, Intrusion & Audio Exception Detection Motion, Temper, Trip Wire, Intrusion, Detection 5 to 90% RH Yes(digital) S,G Specification Standard Premium Power Supply User Adapter PoE Ethernet WiFi Audio IN Audio Out Alarm IN Alarm Out Connectors Casting Physical Material Colour Dimensions Weight 12V DC Yes (802.3af, Class 3) No No No No No Yes Yes Yes Aluminum White 150mm x 70mm 500 g(Approx) Power Consumption 12VDC 0.7A; max: 8.5W PoE (36V to 57V)(0.3A to 0.2A); max: 10W Technical Specification 0 0 -20 C to +50 C

metal components and plastic components must be disposed through recyclers. If you are unable to dispose-off the products or unable to locate e-waste recyclers, you may return the products to Matrix Return Material Authorization (RMA) department. Disposal of Product after End-Of-Life The product refered is covered by the waste Electrical and Electronic Equipment (WEEE) directive and must be disposed of in a responsible manner. WEEE Directive 2002/96/EC www.matrixvideosurveillance.com Head Office 394-GIDC, Makarpura, Vadodara - 390010, India Ph: (+91)1800-258-7747 Email: [email protected] MATRIX COMSEC V.2, March ’2021