Newco Bistro 10 T3 Operating Instructions Manual

Operating Instruction Manual Model B-10-T3 1-800-325-7867 3650 NEW TOWN BLVD ST. CHARLES MO 63301 WWW.NEWCOCOFFEE.COM ...

Introduction & Newco Product Warranty ............ 4 Machine Dimensions & Specifications ................ 5 Machine Features .................................................. 6 Plumbing Connections ......................................... 7 Installation Instructions ........................................ 8 Set up instructions for Bistro 10 T-3 Machine ... 9 Product Installation Procedure ............................ 9 Drink Selection and Keypad Display ................. 12 Programming Instructions.................................. 12 Programming -Machine Calibration ................... 18 Programming-Changing the Drink recipes ...

not damage or destroy these notices as they are for your protection ! WARNING  DO NOT OVERLOAD CIRCUIT.  ALWAYS ELECTRICALLY GROUND THE CHASSIS OR ADAPTOR PLUG.  DO NOT DEFORM PLUG OR CORD.  FOLLOW NATIONAL AND LOCAL ELECTRICAL CODES.  KEEP COMBUSTIBLES AWAY. FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE, FIRE OR SHOCK HAZARD. READ THE ENTIRE OPERATING MANUALBEFORE USING THIS PRODUCT ...

INTRODUCTION This machine is intended to brew 8-12 ounce single serving of coffee and / or powdered hot drinks into a cup. This machine will also dispense hot water for allied beverage use. It is intended for indoor use only on a sturdy counter or shelf. WARRANTY Applies to all equipment manufactured after 2/1/2017. This warranty supersedes all other previous warranties that are currently in manuals. Newco warrants equipment manufactured by it for 1 year parts and labor. Accessories and Dispensers 1 Year parts only. Electronic Circuit and Control Boards- 3 years parts, 1 year labor. Equipment manufactured by oth ...

120 VAC-1600W HEATER-15A USA POWER SUPPLY 120 VAC-1400W HEATER-15A CANADIAN POWER SUPPLY 1/2 GALLON TANK 8-12 OZ CUP SIZE TEMPERATURE RANGE 180-205F DRIP TRAY & DRIP TRAY GRATE l WATER INLET & POWER SWITCH l PRODUCT SELECTION SWITCH PAD & DISPLAY l PRODUCT DISPENSE AREA (CUP) l COFFEE OUTLET l RINSE BUTTONS WHIPPER CHAMBERS D l DISPENSE NOZZLES L LIQUID COFFEE BIBS L MILK CANISTER L REG OFFEE INLET l DECAF COFFEE INLET l CHOCOLATE CANISTER L FLAVORED CANISTER L ...

 DECAF BUTTON SWITCHES TO DECAF BIB  WHIPPER RINSE BUTTONS  AUTOMATIC POWDER LEVEL RESET  PRE-PROGRAMMED DRINK RECIPES  BUTTON ASSIGNMENT FOR RECIPES  INDEPENDENT POWDER HOPPER COUNTDOWN & RESET  CUSTOM CALL FOR SERVICE NUMBER  POWER SAVE & POWER DOWN OPTION  WATER FILTER MONITORING OPTIONS  BEEPER VOLUME CONTROL  PUSH & HOLD HOT WATER BUTTON  DUMP VALVE DELIVERY FOR POWDERS  4 LB HOPPER SIZE THIS IS CONFIGURED AND READY TO DISPENSE 8-OUNCE DRINKS. TO CHANGE RECIPES SEE PROGRAMMING SECTION, MACHINE SET-UP. ...

CAUTION: Disconnect Power to machine before proceeding with plumbing installation. 1) Attach water line to water filter, rear of machine. 2) Flush water line before installing machine. Machine should be connected to COLD WATER LINE ONLY. 3) Water pressure should be at least 40 lbs. For less than a 25 ft. run, use 1/4" copper tubing and connect to 1/2" or larger water line. For longer runs, use 3/8" copper tubing & connect to 1/2" or larger water line and provide an adapter fitting for connection to the brewer. A dedicated water line is necessary for this machine. Minimum flow rate is 1GPM. 4 ...

electrical circuit. Warranty will be void if machine is connected to any voltage other than that specified on the nameplate serial tag. 1) Machine must be on a flat and level surface. Plug or wire in machine to appropriate voltage as noted on the brewer serial tag. Serial tag is located on inside of machine. 2) With water line connected, turn machine power ON (power switch located lower left rear of machine). Install Drip tray and drip tray grate under brew area (slide tray between guide rails until seated). 3) Tank will automatical ...

Fill and install ingredient hoppers with nozzles turned up, Flavored (French Vanilla, Caramel, etc.) on the left, Chocolate in the center and Milk on right. Make sure “button” on bottom of hopper is seated in slot in sheet metal. Slight manual rotation of the auger gear may be necessary to seat hopper in correct location. Rotate dispense nozzles down into whipper bowl. Turn machine on, machine should start filling, will shut off when full. Heater will turn on when tank is at probe level and will display “Heating: Please Wait”. When machine temperature reaches brew temp, display will change to “ ...

 Remove the plastic insert from the BIB fitment as shown in Figure 4.  Using finger and thumb only to prevent over-tightening, thread the BIB connector on to the BIB fitment until seated as shown in Figure 5. Fig. 5 Fig. 4 ...

 Place the product in the storage compartment as shown in Figure 6.  Position the tubing as shown in Figure 7-repeat for 2nd BIB- NOTE COFFEE BIB IS LH CONNECTOR AND DECAF BIB IS RH CONNECTOR SEE PAGE 5 Fig. 6 Fig. 7 ...

Programming Instructions To enter into “Programming Mode”, hold the ‘Decaf’ button for 7 seconds. (Note, after 2 seconds display will change to Sanitation Mode, continue holding button until display reads “Maintenance ”). . The machine readout will display in the Message Display Area. Programming Instructions (Cont’d) PRODUCT SELECTION BUTTON MESSAGE DISPLAY AREA SELECTION INDICATOR LIGHT PROGRAM ACCESS AND RESET BUTTON THESE BUTTONS ARE USED TO ENTER A MENU CHOICE OR ADJUST A VALUE THESE BUTTONS ARE USED TO SCROLL UP & DOWN THROUGH THE MENU SCREENS LOOK FOR ICONS ON DIS ...

Pressing the “CAFÉ LATTE” Button will scroll forward through the Select Menu Choices Pressing the “VANILLA LATTE” Button will scroll backwards through the Select Menu Choices Pressing the “CAFÉ LATTE” button repeatedly will loop the display in 5 Modes: Maintenance---Statistics---Setup---Calibration –Recipe Entry--Exit Program Mode Maintenance 1. Press “Coffee-Regular”Button to Select “Maintenance” 2. Press “Café Latte” Button to toggle Select Menu display Install Sanitizing solution-Push Decaf Button to Start Sanit ...

2. Press “Café Latte” Button to Toggle display Water Temperature Setting (170-205 F) Buzzer volume 0-25 Filter Monitoring (On or Off) Filter size 500 1000 1500 5000 gallons (Only displays if “ON”) Energy Save (Off, Semi [140F], Full [0FF] Energy Time -.5 to 4.0 Hrs After Last push (Only displays if “ON”) Assign Recipes To Buttons *See Page 15 Edit Global Ratio (Default Ratio is 30:1-Can change to 25, 35, 40, 45:1) Call for service # (Re-settable phone Number) *See Page 16 Powder Tracking (On or Off) Left Hopper Value-Grams of Chocolate in ...

1. Press Button to Select “Setup” 2. Toggle Selection to “Assign Recipes” 4. Scroll Up & Down Recipe Choices with these Two Buttons 5. Select Recipe to be Assigned a Button 6. All lights will Flash Depressing a Button will Assign the New Recipe to that Button 7. Selection Screen Will Return to “Assign Recipes” (Return to Instruction #3 to Repeat Button Assignment or Instruction #2 to Exit Menu ) 3. Select Assign Recipes ...

58 Hot Cocoa16oz Mild 115 Car Latte 6oz Dbl 172 Ice Van Lat 12oz Reg 229 Iced Cappo 16oz Reg 2 Coffee 6oz Reg 59 Hot Cocoa 16oz Reg 116 Car Latte 6oz Tpl 173 Ice Van Lat 12oz Bld 230 Iced Cappo 16oz Bold 3 Coffee 6oz Bold 60 Hot Cocoa16oz Bold 117 Car Latte 8oz Sgl 174 Ice Van Lat 16oz Mld 231 Iced Cappo 20oz Mild 4 Coffee 8oz Mild 61 Espresso Shot Sgl 118 Car Latte 8oz Dbl 175 Ice Van Lat 16oz Reg 232 Iced Cappo 20oz Reg 5 Coffee 8oz Reg 62 Espresso Shot Dbl 119 Car Latte 8oz Tpl 176 Ice Van Lat 16oz Bld 233 Iced Cappo 20oz Bold 6 Coffee 8oz Bold 63 Espresso Shot Tpl 120 Car Latte 10oz Sgl 177 Ice Van Lat 20oz Mld 234 Iced Cappo 2 ...

Note: Whenever the machine detects a service problem, a description of the problem and a “Call for Service” Telephone Number Scrolls across the Display. This number can be changed during machine Set-Up. Select the “Call for Service # in the “Set-Up” Menu 1. Press Button to Select “Setup” 2. Toggle Selection to “Call for Service #”(0-000-000-0000 is default #) Character Set (A) A-Z Character Set (a) a-z Character Set (9) 1-9 Character Set (@) ! “ # $ % & ‘ ( ) * + , - . / 0 1 2 3 4 5 6 7 8 9 : ; < = > ?@ (SPACE) 3. Select “Call for Service # 4 ...

Calibration 1. Press Button to Select “Calibration” 2. Toggle Selection to “Calibration” 4. Press Button to Toggle display Mix Bowl Calibration Value (Ounces) Left Auger Speed 0-10 Left Auger Calibration Value in grams Center Auger Speed 0-10 Center Auger Calibration Value in grams Right Auger Speed 0-10 Right Auger Calibration Value in grams Coffee Calibration Value (Ounces) Exit Calibration “LH Mix Bowl Cal”, Insert a measuring container capable of holding 32 or more ounces of water under delivery area of machine, then press the top left button to start calibration countdown period of 30 seconds. (Note ...

value, 1-10, to adjust the auger motor speed for delivering powdered product. This value should remain at 9 or 10 for most powdered products. Value is set at 9 at the factory. “Left Auger Cal” (Flavored), remove LH whipper chamber and hold a 12 ounce plastic cup under the left auger dispense spout, then press either of the top two buttons to start calibration countdown period of 30 seconds. At the end of the calibration cycle, display will change to “Adjust Value”. Use the upper left buttons to toggle the value, increasin ...

Changing the Drink recipes TYPE: Type of recipe, i.e. Coffee, Latte, Hot Chocolate, etc. PERIST. PRETIME: Time in 1/10th of a second Coffee Pump runs w/o water. COF VOLUME: Volume, in ounces, of the coffee portion of the drink. COF DLY TIME: Time in 1/10th of a second Coffee portion of the drink is delayed. PUMP SPEED: Adjusts Coffee strength-speeds 1-25, 25 is the highest strength. MIX BWL VOL: Volume, (oz.) of the Flavored, Milk, Choc. portion of drink. MIX BWL DLY: Time in 1/10th of a second Coffee Pump runs without water. MIX BWL RUN TIME: Cannot change, info only. (Info for coffee delay, i.e.) FLAVOR GM/OZ ...