National Instruments FD-11605 Quick Start Manual
Text of the manual
Caution Before installing your device, read all product
documentation to ensure compliance with safety, EMC, and
environmental regulations.
Attention Avant d’installer votre périphérique, lisez toute la
documentation se rapportant au produit pour vous assurer du respect
des règles concernant la sécurité, la CEM et l’environnement.
Achtung L
10 A TOTAL
9-30 V
FieldDAQ
STATUS
OUT
(9)
(3)
Caps
BANK 1
BANK 2
0
1
2
3
0
1
2
3
Contents I Contenu I Inhalt
内容 I 내용 I 内容
Pinout I Brochage I Pinbelegung
ピン配列 I 핀출력 I 引脚
FD-11605
±16V/±60V AnalogInput
0
10/100/1000
LINK/ACT
SYNC
1
IN
10 A TOTAL
9-30 V
FieldDAQ
STATUS
OUT
BANK 1
BANK 2
0
1
2
3
0
1
2
3
Aux2
Aux1
C
V
Chassis
Ground
BI_DA+
(TX+)
BI_DC–
(No Connect)
BI_DC+
(No Connect)
BI_DD–
(No Connect)
BI_DB–
(RX–)
BI_DD+
(No Connect)
BI_DA–
(TX–)
First install application development software (if applicable). Then install the most current
supported version of NI-DAQmx.
Installez d’abord le logiciel de développement d’application (le cas échéant). Ensuite,
installez la version la plus récente supportée de NI-DAQmx.
Installieren Sie zuerst die Entwicklungsumgebung (sofern zutreffend). Instal
Connect signals to the FieldDAQ. Refer to the user guide for complete signal connection information.
Connectez les signaux au FieldDAQ. Reportez-vous au guide de l’utilisateur pour obtenir des informations complètes sur la connexion
des signaux.
Verbinden Sie Signale mit dem FieldDAQ. Weitere Informationen zur Signalverbindung fi nden Sie in der Bedienun
±16V /±60V Analog Input
Connect Ethernet Port 0 on the FieldDAQ to a network port or directly to the network card in your computer. Then connect the power supply to
the Power IN Port.
Raccordez le port Ethernet 0 du FieldDAQ à un port réseau ou directement à la carte réseau de l’ordinateur puis connectez l’alimentation au port
Power IN.
Ve
Open MAX. If the device is listed, right-click it and select Add Device. If it is not listed, right-click Network Devices and select Find Network NI-DAQmx Devices. Select a device or manually
enter the hostname or IP address. Click the troubleshooting link for help.
Ouvrez MAX. Si le périphérique est répertorié, cliquez dessus avec le bouton droit et sé
Take your fi rst measurement in MAX. Right-click the FieldDAQ and select Test Panels. Click
Start to verify measurement functionality.
Effectuez votre première mesure dans MAX. Faites un clic droit sur le FieldDAQ et sélection-
nez Panneaux de test. Cliquez sur Démarrer pour vérifi er la fonctionnalité de mesure.
Führen Sie Ihre erste Messung im MAX
©2019 National Instruments
All rights reserved.
Software
ni.com/downloads/drivers
NI-DAQmx
Demonstrations
ni.com/daq/videos
Pinouts
In MAX, right-click FieldDAQ
Examples
ni.com/info daqmxexp
Services and Support
ni.com/services
FD-11605 Documentation
ni.com/manuals FD-11605
AI1
AI2
AI3
AI4
AI5
1
2
3
4
5
Designing TSN System