Leader Fox Exeter Operating Instructions Manual
Text of Leader Fox Exeter Operating Instructions Manual
Electric Bicycle Operating
Instructions
Under the law, the dealer is obliged to attach the LEADER FOX Electric Bicycle Operating Instructions to every product
Exeter
Awalon
E – BIKE POWER RIDE
Please read carefully all the information regarding your E-LF product to ensure optimal functioning of your
e-bike. The following text containing a comprehensive description will provide you with information on all
aspects and details (including installation, setting up and general use of the display) regarding the use of
our display. This instruction document will also help you solve potential problems and failures.
What is an
Factors influencing the electric bicycle range
1. Rolling resistance of the tyres. Leader Fox e-bikes are fittet with tyres with low rolling resistance and
increased resistance to puncture. It is also important that the tyres are infla
The system uses monitoring of torque, monitoring of speed of the pedal assist system and monitoring of
real speed of wheels.
The system uses a dual protection feedback for measuring the speed signal to ensure safety and
reliabilityof the system.
Speed sensor is used for a more comfortable and smoother ride, with less effort on the rider
It is highly efficient with low power consumption, long range, low noise levels, and smooth operation.
Descr
Leader Fox Exeter Do not throw the battery into fire.
Do not throw the battery into water.
Do not use the battery for other appliances. It has been made specifically for this model.
Do not dismantle or modify the battery.
Do not connect the positive and negative poles of the battery.
Charger:
Do not dismantle or modify the charger.
Do not use the charger for other appliances. It has been made specifically for this model.
Do not throw the charger
Battery charging and maintenance:
Charge the battery in a dry enviroment to avoid short-circuit damage.
Charge the battery to at least 60% of the capacity once every 3 months even when the bicycle is not used.
Do not cover the battery or the charger.
Do not leave the battery constantly connected to the power source.
Do not use the battery for other appliances. It has been made specifically for this model.
Do not disassemble or modify the battery pa
If the charge indicator shows that the battery is discharged, there is still a minimum voltage level in it
which protects it against damage but is not enough to power the electric bicycle. Recharge the battery as
soon as possible. Never leave the battery fully discharged, it could results in its damage.
In the case, that the battery will be turned on more than 30 min and bike will not be used, the battery will be
automatically switched off.
Proper care of
Intelligent LCD display APT TFT850C
Supplier:
Tianjin APT Development Cop., Ltd.
Electrical parameters:
Battery supply 36V
Rated operating current 40mA
Max operating current 100 mA
Off leakage current < 1 uA
Maxoutput current to controller 100mA
Operating temperature –20 ~ 70 °C
Storage temperature –30 ~ 80 °C
Dimensions and materials:
High-contrast TFT colorful display.
Prodcut shell is ABS, transparent window is made withhigh s
TFT screen instruction:
Battery indicator of capacity (48,2V at illustration image)
Speed indicator – AVG speed, MAX speed, RT speed
Light and display backlight indicator
Km or Mile set value
5 levels pedal assistance
POWER indication (492w at illustration image)
Distance indication – Trip, ODO (total distance), Riding time
Time (12:38AM at illustration image)
In the case of automatic deleting the time and riding distance is it possible, that display b
Please pay attention to the tightening torque of screws. Damage caused by excessive tightening torque or
incorrect assembly / disassembly is not covered by warranty.
A –controller clamping jaw
Open the controller clamping jaw and place it on handlebars in your chosen position. Use an Allen wrench to
tighten the locking screw M3x8.Tightening torque: 1 Nm
1 –Red wire: Anode (24V/36V)
2 –Blue wire: Power cord to the controller
3 –Black wire: GND
4 –Green wire: RxD (controller -display)
5 –Yellow wire: TxD (display -controller)
Turning on the electrical system of the e-bike
Before switch on of the system please check electrical wiring.
Switch on power of the electrical system on battery, colored backlighting illuminates.
Switch on display with press and short hold (1,5 second) POWER button. Display will automatically turns off
if it is not used for a while. Can be set range 0 ~ 9 minutes (or OFF).
After ride turns off e-bike in the same way.
Press and hold UP button for
Speed and mileage mode switch
Short press POWER button can change the speed and mileage mode
Headlight/Backlight On/Off
Press and hold UP button for 1 second can turn on/off the headlight and the screen will switch to the
corresponding mode.
The motor does not work when battery voltage is low. Display still can keep the headlight on for a while
when e-bike is in riding.
Data cleanup
Press and hold UP and DOWN button together for 1 second can reset several
Leader Fox Exeter By double press POWER button (interval less than 0,3 second) can get into setting menus.
Press UP/DOWN buttons to change the parameter setting, press POWER button toswitch to next item.
Double press POWER button will exit from menu.
Display will automatically quit menu when there is no operation for 30 seconds.
For safety reasons, you can not enter the settings menu while riding.
Language
Press UP/DOWN button to switch between languages.