hattrick EVOLUTION Operation & User’s Manual

Text of hattrick EVOLUTION Operation & User’s Manual

EVOLUTION USER MANUAL

Read all instruction carefully before use this product. Read all instruction carefully before use this product. Retain this owner’s manual for the future’s reference !

hattrick EVOLUTION Warning: Now here we suggest that you should consult with your physician or health professional before

starting your workout, especially for the age up to 35 old or once-health problem people. We take no responsible for any troubles or hurts if you don’t following our specification. Treadmill will be carefully assembled and covered the motor shield, then connect to the power. ATTENTION: 1. Ensuring the safety clamps were attached to t

hattrick EVOLUTION When you open the carton, and you will find the below parts in the carton

ASSEMBLY INSTRUCTIONS When you open the carton, and you will find the below parts in the carton Parts list: NO. DES. Specification Nos. NO. DES. Specification Nos. 1 Main frame 1 70 Bolt M8*55 2 12 Wrench screw Driver S=13\14\15mm 1 105 screw ST4.2*19 6 13 5# Allen Wrench 5mm 1 103 screw ST4.2*20 4 14 6# Allen Wrench 6mm 1 86 Lock washer 8 10 31 Right base

hattrick EVOLUTION 1.Open the carton, get out the above

spare parts, and put the Main Frame onto the level ground. Use the 5#Allen Wrench to fix the right upright onto the base frame with Bolt M8*55(70) and Lock Washer(86), and fix at the other side of this upright with Bolt M8*16(67) and Lock Washer(86) Same way for the Left upright. NOTICE; PLEASE HOLD THE UPRIGHT WHEN FIXING IT ONTO BASE FRAME TO AVOID HURT. 1. Push up the Computer and L &

1. Use the 5# Allen wrench to fix the

computer frame onto left and right uprights(3、4) with bolt M8*45(62) and Lock washer(86) NOTICE, PLEASE HOLD THE COMPUTER FRAME BEFORE YOU HAVE TIGHTEN THE BOLT TO IN VOILD FALLING DOWN AND ESCAPE ANY HURT. 1. Use wrench screw driver to fix the right base cover(31) onto the right upright(3) and base frame(2) with ST4.2*19 screw(105). Use the same way to fix the left upright. 2. Use wrench scr

ATTENTION:Please confirm complete assembly as the require above and lock all the bolt. Do the

following operation after checking everything is OK. Before you use the treadmill, please read the instruction carefully. Hold and push up the base frame at position A, push harder until hear “Bi..” from the elastic pull pin. ATTENTION: when pulling up, the main frame will move forward, please hold on the handbar. The transpor

This product must be grounded. If it should malfunction or breakdown, grounding provides a part of least

resistance for electric current to reduce the risk of electric shock. This products is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. DAN

hattrick EVOLUTION LED WINDOW DISPLAY:

1.Speed window show current speed values. 2.Time window show running time. 3. DIST/CAL window show the running distance or calorie consumption alternately. 4. INC/PUL window show the incline value or the heart beating value alternately. When runner hold the handpulse sensor, the window will show the heart beating value.

1.”MODE”:press MODE under standby mode, the user can choose below function circlely, “0:00” manual

operation mode, it’s default mode by the system. Default speed under manual operation mode is 1.0 KM/H. “15:00” Time counting down mode. “1.0” Distance counting down mode. “50” Calorie counting down mode. In any mode, the user can set up countdown number through “SPEED+”“SPEED-”or“INCLINE+”“INCLINE-”,

5. Press “STOP” the mathine will slow donw until stop running.

6. Hold handle pulse for 6 seconds, the window will display the user’s hearbeat rate. MANUAL MODE 1.Under standby mode,press “START” botton,treadmill starts in speed 1.0km/h and in gradient zero; other windows count forward from zero, press“INCLINE+”、“INCLINE-”、“SPEED+”、“SPEED-” to change speed and gradient. 2.Under standby mode, press “MODE”to enter t

Settting time/20 = interval

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 P01 SPEED 2 3 3 4 5 3 4 5 5 3 4 5 4 4 4 2 3 3 5 3 INCLINE 1 1 2 2 2 3 3 3 2 2 1 2 2 1 1 3 3 2 2 2 P02 SPEED 2 4 4 5 6 4 6 6 6 4 5 6 4 4 4 2 2 5 4 2 INCLINE 1 2 2 2 2 3 3 2 2 2 2 2 3 3 3 4 4 3 2 2 P03 SPEED 2 4 4 6 6 4 7 7 7 4 7 7 4 4 4 2 4 5 3 2 INCLINE 2 3 3 2 2 3 3 3 2 2 2 2 4 4 4 6 6 3 2 2 P04 SPEED 3 5 5 6 7 7 5 7 7 8 8 5 9 5 5 6 6 4 4 3 INCLINE

USER DEFINED PROGRAM

There are three program U1, U2, U3 for user defined. 1.User define program setting Press “PROGRAM” continuously under standby mode until window display U1-U3,press “MODE” to start setting first segment, setup speed and incline by pressing “SPEED+”“SPEED-”AND “INCLINE+”“INCLINE-”, press “MODE” finish first segment seting and enter second one, until finish all 20 segments. The data will be permanently sa

SAFETY KEY FUNCTION

The treadmill will stop emergently by pulling off the safety key in any situation, TIME window will display “―――” with buzzing for 3 time. At this moment, the computer accept no operation command except power off. Put the safety back to the position, the treadmill will enter standby mode and waiting for operation command. POWER SAVE MODE The system have Power saving function, system will enter power saving mod

settle the problem, try to change a good transformer.

2.Display E01: Message failure. Probable reason: The wires from computer and bottom control board didn’t connect well, please check each wire. If the wire was destroyed, change a good one. 3.Display E02: Burst clash. Check the power is right, if not, use correct power to test; Check if the bottom control was burnt out, change a good one; reconnect the motor wire. 4.Display E03: No sensor signal. Th

Learn how to adjust the speed and incline before using. Walk about 1 km at stable velocity and write

down the time, it will take you about 15-25 minutes. If walk at 4.8 km/h, it will take you about 12 minutes in 1 km. If you feel comfortable at the stable velocity, you can add the speed and incline, after 30 minutes, you can have good exercise. At this stage, you can not add the speed or incline too much at one time, it can keep you feel

Speed 9.0-12.0KM/H intermediate speed walking

Speed 12.0-14.5M/H well experiences of running Speed 14.5-16.0KM/H excellent runner Attention: The speed of movement ≤6KM/H , the normal walking; The speed of movement ≥8.0KM/H ,the runner. WARM-UP INSTRUCTION Take warm-up exercise before workout for 5-10mints.It’ easy to start training with warm-muscle. Training following this method for 5-times, each leg doing for 10seconds or more ,do it again after

RUNNING BELT ADJUSTMENT

Warning: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE CLEANING OR SERVICING THE UNIT. Clean: General cleaning or the unit will greatly prolong the treadmill. Keep treadmill clean by dusting regularly. Be sure to clean the exposed part of the deck on either side of the walking belt and also the side rails. This reduces the build up of foreign material underneath the walking belt by wearing the clean running shoes

CENTER THE RUNNING BELT

●Place treadmill on a level surface. Run Treadmill at approximately 6-8KM/H, checking the running condition. If the belt has drifted to the right, pull out of the save clock and switch, turn the right adjusting bolt 1/4 turn clockwise, then start running until centering the belt. PIC A If the belt has drifted to the left ,pull out of the safety clock and switch, turn the left adjusting bolt 1/4 turn clockwise ,then start runnin

Specification Qty NO.

Description Specification Qty 1 Main frame 1 48 Computer bottom wire 1 2 Base frame 1 49 Safety lock 1 3 Right upright Group 1 50 Light inductor 1 4 Left upright Group 1 51 Magnitic ring 1 5 Handle frame 1 52 Power switch 1 6 Incline motor bracket 1 53 Standard power wire 1 7 DC motor bracket 1 54 Overload protector 1 8 Rotation Tube Plug 2 55 AC single line 1 9 Cylinder 1 56 Blue single line 1 10 Fr

hattrick Treadmill Owners Instructions: