Icom IC-M802 Notes On Operation

Text of Icom IC-M802 Notes On Operation

Notes on operation of the ICOM IC M802:

1. It has been noted that the ICOM IC M802 does not like to send DSC messages in low power. For some reason the Antenna tuner cannot tune and results in High reflected RF waves (SWR). This results in improper transmission of the digital calling message. No similar problem has been noted when the radio is set to medium or high power. 2. Since there is no option to press the tune button when sending a DSC message.

1. Press the [FREQ/CH] button until two frequencies are shown, one above the other.

At this point they may or may not be the same frequency. The upper is the receive Frequency and the lower is the transmit frequency. Press the [TXF/TX] button. 2. Note: The TX in the middle left side of the [Function Display] will flash on and off. 3. Using the key pad, press [0] 4. The [Function Display] lower (smaller) number should now display 0 5. Press and Hold the

HF Marine Operators (WLO Radio)

WLO Radio has taken over all US HF based Marine Operators and is available on many frequencies. To sign up with them call 334-665-5110. Give them a credit card number to keep on file so that if in an emergency you need to make a call you do not have to broadcast your credit card number around the world. They have had my card on file for years and will not charge you for anything but calls made. WLO ITU CHANNEL

Delete published procedure for Group Calls starting On Page 94

Insert: Group DSC Call Procedure: 1. Press [DSC] button to go to the DSC WATCH display. 2. Press [SET/MODE] button to go to the DSC MENU. 3. NOTE: Press [SET/MODE] button at any time to cancel the procedure and [FREQ/CH] button to move back one menu screen. 4. Rotate [CH] knob to select Group 5. Press [ENT] button to display Group – Group ID menu 6. Select what Group the message

7. Rotate the [CH] knob to select the desired traffic

frequency. a. Press [ENT] button to continue to the Group – Call frequency menu. b. IF Manual set is selected, enter the nine digit Group ID. i. Press [ENT] button to continue to the Group – Call frequency menu. 8. Rotate the [CH] knob to select the desired calling frequency and press [ENT] to display a summary of selected items. a. IF Manual set was selected, enter the desired calling frequency and

The procedures in the book assume the channel is

programmed so step 1, changing the mode does not work for a blank channel. The following procedure replaces step one and two and will work for both blank and programmed channel programming. Step 1 – Input the Receive Frequency & Mode of Operation The frequency is programmed in kHz for the IC – M802. That means if you are trying to program 15MHZ, you need to enter 15000.0. 1. Press

Icom IC-M802 Step 2 – Input the Transmit Frequency

This step only needs to be completed if the transmit frequency is different than the receive frequency. For many shore stations such as WLO radio, the marine telephone operator, the transmit frequency is different than the receive frequency. This is called duplex operation as opposed to simplex where the same transmit and receive frequency is used. One nice feature on the IC – M802 is that it automatically assume

9. Note: The TX in the middle left side of the [Function Display] will flash on and off.

10. Using the key pad, press [8]; then [2]; then [6]; then [4]; then [0] 11. The [Function Display] lower (smaller) number should now display 8.264.0 12. Press and Hold the [ENT] button until the TX in the middle left side is removed. 13. The channel is now programmed for 8264.0KHz frequency. 14. Note in the upper part of the [Function Display] the SIMP is now changed

Icom IC-M802 b. The Channel Indication display shows the label with the

channel number below. If no label has been entered, the Receive Frequency with the channel number below will be displayed. 2. Press the [FREQ/CH] button to display the label display if not shown. 3. Press [F] button. 4. Note: F in the upper right side of the [Function Display] 5. Press [FREQ/CH] button to display the label input. The underscore/digit at the left most letter or blank will blinkin

11. IF it is already a blank, rotate clockwise the [CH] knob one click to move the cursor to

the right one additional letter on the [Function Display] 12. Press the [2] key to display a 2 on the [Function Display]. 13. Press the [5] key to display a 5 on the [Function Display]. 14. Press the keys [6], then [6] to display an M on the [Function Display]. 15. Verify the display should read WWVH 25. a. To change a wrong letter or number, use the [CH] knob to m

Trouble with email?

It seems like a lot of folks have issues with email. Email on HF is not as clean as when you are connected to the internet. Here are a few tips to help you get started for both sail Mail and Winlink.  Review the Sailmail Primer: http://www.sailmail.com/smprimer.htm There are some excellent application information in Sailmail Primer and may solve all your issues.  Get the internet mode working first as that will make sure your

2. With your 802 on and your computer running, note the frequency your radio is on. (Press

[FREQ/CH] if need be to obtain the frequency display. Receive Frequency over the Transmit Frequency.) 3. Open Airmail 4. Select Module, then HF Terminal. 5. Does your frequency change on the 802? 6. If so, the computer is directly or via the modem controlling the IC M802. a. If not you need to figure out how to get the computer to control the radio. b. IF the radi

13. You can use the pull down on the transmit control screen to select the station and the frequency

or double click in the Propagation display on the frequency (on the left side of the propagation chart.) 14. Listen to see if you can hear others getting mail. a. Don’t start till it is clear. b. Most stations monitor several frequencies, but only do email one at a time so it may say busy. c. If you can hear others getting email, you should be able to get

Appendix XII – Improving DSC Calling for Cruisers

Discussion Factory programming only includes one usable calling frequency, 2177.0KHz, for cruiser to cruiser communications. This is because all the other frequencies are duplex frequency intended for calling shore stations. 2177.0KHz is not a long range communications frequency. While a higher frequency might get you to the US from Mexico, 2177.0 KHz, may not make it across the Sea of Cortez during

Re-programming the IC M802 to utilize simplex calling channels is easy. Re-programming of the radio

will change both the transmit and receive frequencies to those listed as the transmit frequencies in the table. The 2177.0 channel is already a simplex channel and will be retained. Both the Scan Frequencies and Call frequencies must be changed. A custom procedure specific for this change to the radio is provided below. Delete the old Scan Frequencies

Icom IC-M802 INTER 4-1, 6-1, 8-1, 12-1 16-1 frequencies. Leaving the other frequencies programmed, e.g INTER 4-2,

6-2, etc. 1. In DSC Watch press [SET/MODE] to display the DSC MENU. 2. Rotate the [CH] knob to select Set up and press [ENT]. 3. Rotate the [CH] knob to select Call frequency and press [ENT] 4. Rotate the [CH] knob to select (INTER 4-1, 6-1, 8-1, 12-1 16-1 duplex frequencies one at a time for deletion) and press [ENT]. 5. Press and hold the [CE] until two

Program the new Call frequencies.

1. Rotate the [CH] knob to select and press [ENT]. 2. Using the Keypad, enter the desired label for the new frequency, e.g. 4MHz Ship, 6MHz Ship, 8MHz Ship etc. 3. Rotate the [CH] Knob to move to the TX:_ _ _ _ _ . _KHz and enter the new frequency. {4MHz: 4,208.0; 6MHz: 6,312.5; 8MHz: 8,415.0; 12MHz: 12,577.5; 16MHz: 16,805.0} 4. Rotate the [CH] Knob to move to the RX:_ _ _ _ _ . _KHz and enter the same frequen

Icom Marine Radio Owners Instructions: