First Alert 7319DFB Operations & Installation Manual

Text of First Alert 7319DFB Operations & Installation Manual

7319DFB / 7334DFB

Manual # M08-0457-006 www.FirstAlert.com FIRE RESISTANT GUN SAFE Operation & Installation Guide THEFT FIRE 30minutes /1400ºF RATED Manual # M08-0457-006

important: Do not return saFe to store

If you are missing parts or have any other questions pertaining to its proper use and care, Do not return your safe to the store. Please contact Consumer Affairs at 1-800-323-9005, 7:30 a.m. – 5 p.m. Central Standard Time, Monday through Friday. To assist us in serving you, please have the model number and date of purchase available when calling. 1 2 For Your Protection a Do not remove the serial number tag from t

diaGraM exterior (MODEL 7319DFB)

diaGraM interior (MODEL 7319DFB) diaGraM interior (MODEL 7334DFB) INTERIOR CONFIGURATION, LOCkING BOLTS AND BOLT WORk MAY VARY ON SOME MODELS INTERIOR CONFIGURATION, LOCkING BOLTS AND BOLT WORk MAY VARY ON SOME MODELS Heat Expandable Door Seal Top Shelf Safe Interior Walls Gun Rack Side Shelf (3) (Varies based on model) Divider (1) (Varies based on model) Bolt Down Hole Cap (4) Locking Bolts (10) Fire Resistance Labe

reMovinG tHe SaFetY interLocK Screw

batterY inStaLLation 1 Locate the 9V Alkaline Battery in the plastic bag. 2 Remove the Phillips head screw from the battery cover located on the bottom of the keypad. 3 Connect the battery and gently insert the battery up inside the keypad and replace the battery cover. 4 Re-install the Phillips head screw in the battery cover. DO NOT OVER TIGHTEN! IMPORTANT: Your safe may have a “Door Lock Override Device” i

To prevent loosening, apply one drop of Thread Lock on the threads of each spoke.

NOTE: Thread Lock is not included. Purchase from your local hardware store. oPeninG SaFe For tHe FirSt tiMe 8 7 inStaLLinG tHe HandLe SPoKeS 2 Screw spokes into the handle hub. 1 Locate two (2) additional spokes inside safe and remove protective covers. Follow OPENING SAFE FOR THE FIRST TIME on page 7 before proceeding. Follow REMOVING THE SAFETY INTERLOCk SCREW an

1. Locate Metal Shelf

Clips inside the safe. 4. Carefully place shelf on top of the clips. 5. To remove clips, squeeze the clip with your hand or pliers and lift up. 2. Insert the top of the clip into the notch. important Four (4) clips are required for each shelf. Make sure all four (4) clips are in alignment before moving on to step 4. 3. Push the bottom of the clip into the lower notch. 1. Write down your new six (6) digit passcode before you proceed. 2

1 Locate the four (4) Concrete Bolts inside the safe.

2 Remove interior shelving and four (4) Bolt Down Hole Caps. 3 Place the safe where you want it bolted down and mark the floor through the holes in the bottom of the safe. 4 Move the safe and drill holes in the floor with a 5/8 inch masonry bit. 5 Reposition the safe over the holes and install the four (4) Concrete Bolts. 6 To prevent heat from entering the safe during fire, fill the holes with a

Your saFe’s unique iDentiFication numBers

When contacting Consumer Affairs, you should be prepared to supply some important information that specifically identifies your safe. This information is extremely important to assuring prompt and accurate customer assistance. It is strongly recommended that you identify and record the following information in the Safe Identification Record form located on page 15. iMPortant Do not remove

First Alert Safes Owners Instructions: