Cisco Firepower 4110 Hardware Installation Manual

First Published: 2016-03-31 Last Modified: 2021-09-13 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 ...

Full Cisco Trademarks with Software License ? Overview 1 C H A P T E R 1 Features 1 Deployment Options 4 Package Contents 4 Serial Number Location 6 Front Panel 7 Front Panel LEDs 9 Rear Panel 10 Network Modules 11 10-Gb Network Module 11 40-Gb Network Module 12 Hardware Bypass Network Modules 14 1-Gb Network Module with Hardware Bypass 15 40-Gb Network Module with Hardware Bypass 16 1-Gb SX/10-Gb SR/10-Gb LR Network Module with Hardware By ...

42 Safety Recommendations 43 Maintain Safety with Electricity 44 Prevent ESD Damage 44 Site Environment 45 Power Supply Considerations 45 Rack Configuration Considerations 45 Rack-Mount and Ground the Chassis 47 C H A P T E R 3 Unpack and Inspect the Chassis 47 Rack-Mount the Chassis 48 Ground the Chassis 52 Installation, Maintenance, and Upgrade 55 C H A P T E R 4 Install, Remove, and Replace the Network ...

Overview • Features, on page 1 • Deployment Options, on page 4 • Package Contents, on page 4 • Serial Number Location, on page 6 • Front Panel, on page 7 • Front Panel LEDs, on page 9 • Rear Panel, on page 10 • Network Modules, on page 11 • Hardware Bypass Network Modules, on page 14 • Power Supply Modules, on page 21 • Fan Modules, on page 23 • Supported SFP/SFP+ and QSFP Transceivers, on page 24 • Hardware Specif ...

The following table lists the features for the Firepower 4100 series. Table 1: Firepower 4100 Series Features 4150 4140 4120 4110 Feature • Common Criteria (CC) and Commercial Solutions for Classified (CSFC) for ASA 9.8.x and FTD 6.2.x • CC for the Network Device Collaborative Protection Profile (NDcPPv2.1) for ASA 9.12.x and FX-OS 2.6.x • Federal Information Processing Standards (FIPS) 140-2 on ASA 9.12.x, FTD 6.4.x, ...

Maximum number of interfaces One Gigabit Ethernet Supports 1-Gb fiber or copper small form-factor pluggable (SFP) Management port One RJ-45 console Serial port One USB 2.0 Type A USB port Eight fixed 1-Gb and 10-Gb SFP ports (named Ethernet 1/1 through 1/8) Network ports Eight fixed 1-Gb and 10-Gb SFP ports See Supported SFP/SFP+ and QSFP Transceivers, on page 24 for a list of support ...

3+1 redundancy Hot-swappable Fan Two SSD slots Ships with one 400-GB SSD installed in slot 1. Slot 1 is the primary SSD and should always be present. RAID is not supported. Note The SSD must be installed in slot 1. Slot 2 is optional and is reserved only for the MSP. Two SSD slots Ships with one 200-GB SSD installed in slot 1. Slot 1 is the primary SSD and should always be present. RAID is not supported. Not ...

Blue console cable PC terminal adapter 2 Firepower 4100 chassis 1 10/100/1000BASE-T SFP transceiver 4 Two power cords (country-specific) See Power Cord Specifications, on page 32 for a list of supported power cords. 3 Tie wrap clamp 6 Two slide rails 5 Flextronics tie wrap 8 Artesyn tie wrap 7 Ten 8-32 x 0.375 inch Phillips screws used to secure the mounting bracket to chassis (six screws), and the cable management ...

The serial number for the Firepower 4100 series chassis is located on the pullout asset card on the front panel. Figure 3: Serial Number on the 4100 Chassis You can also view additional model information on the compliance label located on the bottom of the chassis. Cisco Firepower 4110, 4120, 4140, and 4150 Hardware Installation Guide 6 Overview Serial Number Location ...

Front Panel The following figure shows the front panel of the Firepower 4100. Figure 5: Firepower 4100 Front Panel Gigabit Ethernet management port 2 RJ-45 console port 1 Eight fixed SFP+ (1-Gb/10-Gb) ports (in network module slot 1) Ethernet 1/1 through 1/8 labeled top to bottom, left to right 4 USB 2.0 Type A port 3 SSD 2 Reserved for the optional MSP. 6 SSD 1 Reserved for the primary SSD; slot 1 must always ...

The 10-Gb network module is shown. Note 10 Pullout asset card 9 Network module 3 The 10-Gb network module is shown. Note 11 RJ-45 Console Port The Firepower 4100 has a standard RJ-45 console port. You can use the CLI to configure your Firepower 4100 through the RJ-45 serial console port by using a terminal server or a terminal emulation program on a computer. The RJ-45 (8P8C) port supports RS-232 signaling to an internal UART controller. T ...

The following figure and table describe the Firepower 4100 front panel LEDs. Figure 6: Front Panel LEDs Health (SYS) • Off—System is not booting yet. • Green, flashing—Power-up diagnostics are complete and system is booting up. • Green—The system has passed power-up diagnostics. • Amber—Power-up diagnostics has failed. • Amber, flashing—Alarm; power-up diagnostics are running. 2 Management • Off—No connection or por ...

• Amber—No link or network failure. • Green—Link up. • Green, flashing—Network activity. 7 Rear Panel The following figure shows the rear panel of the Firepower 4100. Figure 7: Firepower 4100 Rear Panel Power supply module 1 2 Power on/off switch 1 Fan module 1 4 Power supply module 2 3 Fan module 3 6 Fan module 2 5 Fan module 5 8 Fan module 4 7 Location for the two-post grounding ...

After removing power from the chassis either by moving the power switch to OFF or unplugging the power cord, wait at least 10 seconds before turning power back ON. Note Network Modules The Firepower 4100 contains two network module slots that provide optical or electrical network interfaces. Network modules are optional, removable I/O modules that provide either ...

Ethernet X/1 2 Captive screw/handle 1 Ethernet X/5 4 Ethernet X/3 3 Ethernet X/2 6 Ethernet X/7 5 Ethernet X/6 8 Ethernet X/4 7 Network activity LEDs • Off—No connection or port is not in use. • Amber—No link or network failure. • Green—Link up. • Green, flashing—Network activity. 10 Ethernet X/8 9 For More Information • For a list of copper SFPs, see Supported SFP/SFP+ and QSFP Transceivers, on page 24. 40-Gb Net ...

module. For instructions on how to verify your firmware package version and to upgrade the firmware if necessary, see the Cisco Firepower 4100/9300 FXOS Firmware Upgrade Guide. See Cisco Firepower 4100/9300 FXOS Compatibility for the software compatibility matrix. Note The FPR4K-NM-4X40G is NEBS-compliant. Note Figure 9: FPR4K-NM-4X40G Network activity LE ...

Hardware bypass (also known as fail-to-wire) is a physical layer (Layer 1) bypass that allows paired interfaces to go into bypass mode so that the hardware forwards packets between these port pairs without software intervention. Hardware bypass provides network connectivity when there are software or hardware failures. Hardware bypass is useful on ports where the Firepower security appliance is only monitoring or logging tra ...

cannot enable hardware bypass on this inline interface set. You can only enable hardware bypass on an inline interface set if all the pairs in the inline set are valid hardware bypass pairs. Note For More Information • See 1-Gb Network Module with Hardware Bypass, on page 15 for a description of the 1-Gb network module. • See 40-Gb Network Module wi ...

Ethernet X/1 Ports 1 and 2 are paired together to form a hardware bypass pair. LED B1 applies to this paired port. 2 Bypass LEDs B1 through B4 • Green—In standby mode. • Amber, flashing—Port is in hardware bypass mode, failure event. 1 Ethernet X/2 Ports 5 and 6 are paired together to form a hardware bypass pair. LED B3 applies to this paired port. 4 Ethernet X/2 Ports 3 and 4 are paired together to form a hardware bypass p ...