DeVilbiss HVLP TRANS-TECH Operation Manual

2 Operation Manual COMPACT – Gravity Feed Spraygun Important Read and follow all instructions and Safety Precautions before using this equipment Description The Compact Gravity feed Spraygun Kit complies to ATEX regulations 94/9/EC, protection level; II 2 G X, Suitable for use in Zones 1 and 2 Important: : These Sprayguns are suitable for use with both waterbased and solvent based coating materials. The design uses EPA compliant (Devilbiss Trans-Tech®) and HVLP atomising technology to reduce overspray and improve coating efficiency. These guns are not designed for use with highly corrosive and/or abrasive materials and if used with such materials it must be expected that the need for cleaning and/or replacement of parts will be increased. If there is any doubt regarding the suitability of a specific material contact your local Distributor or ITW Finishing direct. EE Model Part Number Example: COM-G510B-16 Aircap Fluid nozzle size (16 = 1,6 mm) Gunbody Finish B= Blue Anodised ITW Finishing Systems and Products reserve the right to modify equipment specification without prior notice. EC Declaration of Conformity We: ITW Finishing UK, Ringwood Rd, Bournemouth, Dorset, BH11 9LH, UK, as the manufacturer of the Spraygun model Compact, declare, under our sole responsibility, that the equipment to which this document relates is in conformity with the following standards or other normative documents: BS EN 292-1 PARTS 1 & 2: 1991, BS EN 1953: 1999; and thereby conform to the protection requirements of Council Directive 98/37/EC relating to Machinery Safety Directive, and; EN 13463-1:2001, council Directive 94/9/EC relating to Equipment and Protective Systems intended for use in Potentially Explosive Atmospheres protection level II 2 G X. This product complies with the requirements of the EPA guidelines, PG6/34,PG6/20 and PG6/23. Achieving transfer efficiency in excess of 65%. B. Holt, General Manager 30th June 2003

3 SAFETY WARNINGS Fire and explosion Solvents and coating materials can be highly flammable or combustible when sprayed. ALWAYS refer to the coating material suppliers instructions and COSHH sheets before using this equipment Users must comply with all local and national codes of practice and insurance company r e q u i r e m e n t s g o v e r n i n g ventilation, fire precautions, operation and house-keeping of working areas This equipment, as supplied, is NOT suitable for use with Halogenated Hydrocarbons. Static Electricity can be generated by fluid and/or air passing through hoses, by the spraying process and by cleaning non- conductive parts with cloths. To prevent ignition sources from static discharges, earth continuity must be maintained to the spraygun and other metallic equipment used. It is essential to use conductive air and/or fluid hoses. Personal Protective Equipment Toxic vapours – When sprayed, certain materials may be poisonous, create irritation or be otherwise harmful to health. Always read all labels and safety data sheets for the material before spraying and follow any recommendations. If In Doubt, Contact Your Material Supplier The use of respiratory protective equipment is recommended at all times. The type of equipment must be compatible with the material being sprayed. Always wear eye protection when spraying or cleaning the spraygun Gloves must be worn when spraying or cleaning the equipment Training – Personnel should be given adequate training in the safe use of spraying equipment. Misuse Never aim a spraygun at any part of the body Never exceed the max. recommended safe working pressure for the equipment The fitting of non-recommended or non- original spares may create hazards Before cleaning or maintenance, all pressure must be isolated and relieved from the equipment The product should be cleaned using a gun washing machine. However, this equipment should not be left inside gun washing machines for prolonged periods of time. Noise Levels The A-weighted sound level of sprayguns may exceed 85 dB (A) depending on the set-up being used. Details of actual noise levels are available on request. It is recommended that ear protection is worn at all times when spraying. Operating Spray Equipment using high pressures may be subject to recoil forces. Under certain circumstances, such forces could result in repetitive strain injury to the operator. EE

4 Parts List Ref. No Description Part Number Qty Options 1 Air Cap/Retaining ring See Selection Chart 1 + 2 Nozzle See Selection Chart 1 *+ 3 Separator SP-626-K5 5 *+ 4 Packing GTI-445-K2 2 5 Spreader Valve SP-403-K 1 6 Stud and Screw GTI-408-K5 5 7 Needle Adjusting Screw SP-614-K 1 *+ 8 Spring SP-622-K5 1 + 9 Needle See Selection Chart 1 10 Airvalve housing + seal SP-612-K 1 *+ 11 Spindle 1 12 Trigger SP-617-K 1 13 Connector SP-611-K 1 14 Airflow Valve SP-402-K 1 15 Drip Check Lid kit of 5 GFC-2-K5 1 + 16 Air Valve Service Kit SPK-101-K 1 17 Retaining Ring and Seals SPK-102-K 1 * 18 Spreader/ Cheater Service Kit GTI-428-K5 5 19 Circlip 25746-007-K5 5 20 Cup Lid GFC-402 1 21 Filter KGP-5 1 22 1/2 Ltr Gravity Cup Kit GFC-501 1 * 23 Air Valve assembly Tool 1 24 Spanner SPN-5 1 Spraygun Service Kit (parts included marked + ) SPK-401-** 1 12, 13,16,18,20 e.g ** =16 =1.6 mm EE

5 AIR CAP/ RETAINING RING SP-100-***- K e.g *** = 430 CONVENTIONAL HVLP TRANS -TECH 430,497,443, 470 505 510,522,523,513, 590 Nozzle SP-200S-**-K e.g ** =14 =1.4mm 085,10,12,13,14, 16,18,20,22 085,10,12,13,14, 16,18,20,22 085,10,12,13, 14,16,18,20,22 Needle SP-300S-**-K e.g ** =14 =1.4mm 085,10,12,13,14, 16,18,20,22,28 085,10,12,13, 14,16,18,20,22 085,10,12,13, 14,16,18,20,22 05,07,10 Needle Plastic tipped SP-300P-**-K e.g ** =14 =1.4mm 10, 12, 14 10, 12, 14 10, 12, 14 10 Nozzle Hard- ened SP-200N-**-K e.g ** =14 =1.4mm 14,18, 22 14,18, 22 14,18, 22 Nozzle Hardened ( Air Cap 470 only) SP-247N-**-K e.g ** =22 =2.2mm 22,28 Needle Hardened SP-300N-**-K e.g ** =14 =1.4mm 14,18,22 22,28 14, 18, 22 14, 18, 22 Nozzle (Air Cap 590 only) SP-259S-**-K e.g **=10=1.0mm 05,07,10 Nozzle ( Air Cap 470 only) SP-247S-**-K e.g ** =22 =2.2mm 22,28 CHART : AIR CAPS / NOZZLES AND NEEDLE COMBINATIONS

6 Patent No 2372465 (GB) EE Air supply connection - Universal 1/4“ BSP and NPS Maximum static Air inlet pressure - P1 = 12 bar (175 psi) Nominal gun Air inlet pressure - with gun triggered 2. bar (29 psi) 510 Trans-Tech Air Cap 1.4 bar (20 psi) 505 HVLP Air Cap Maximum Service temperature 40°C Gun Weight - 583 g Materials of Construction Gun body Anodised Aluminium Nozzle Stainless Steel Needle Stainless Steel Fluid Inlet Stainless Steel / PTFE Trigger Nickel Plated Steel Cup Acetal (Anti-static) Cup Lid Acetal (Anti-static) Specification

7 Installation Important: To ensure that this equipment reaches you in first class condition, protective coatings have been used. Flush the equipment through with a suitable solvent before use. 1. Attach air hose to connector (13). Recommended hose size 8 mm bore. The hose must be conductive and electrical bond from the spraygun to earth should be checked with an ohmeter. A resistance of less than 106 Ohms is recommended. 2. Air supply should be filtered and regulated. 3. Attach Cup assembly (22) by screwing into the Fluid Inlet of the spraygun. Tighen when fully home. 1. Turn off air and relieve pressure in the supply lines, or if using QD system, disconnect from airline. 2. Remove Cup Lid (20)and empty coating material into a suitable container. Clean the gun and cup, preferably in a gun wash machine. Clean the cup. 3. Check the breather hole in the Lid and the Drip Check Lid is not blocked. 4. Remove air cap (1) and clean. If any of the holes in the cap are blocked with coating material use a toothpick to clean. Never use metal wire which could damage the cap and produce distorted spray patterns 5. Ensure the tip of the nozzle (2) is Preventative Maintenance Operation 1. Mix coating material to manufacturers instructions. 2. Fill the cup with the required amount of material. Fill to no more than 25mm (1“) from the top of the cup. DO NOT OVERFILL. 3. Attach Cup Lid. 4. Turn needle adjusting screw (7) clockwise to prevent movement. 5. Turn spreader valve (5) counter- clockwise to fully open. 6. Adjust inlet air pressure (For r e c o m m e n d e d f i g u r e s s e e Specifications) at the gun inlet with the gun triggered. (pressure gauge attachment shown under Accessories is recommended for this). 7. Turn needle adjusting screw counter clockwise until first thread shows. 8. Test spray. If the finish is too dry reduce airflow by reducing air inlet pressure or by the Airflow Valve (14). Screw the Adjusting Knob (14) in to reduce pressure. 9. If finish is too wet reduce fluid flow by turning needle screw (7) clockwise. If atomisation is too coarse, increase inlet air pressure. If too fine reduce inlet pressure. 10. The pattern size can be reduced by turning adjusting valve (5) clockwise. 11. Hold gun perpendicular to surface being sprayed. Arcing or tilting may result in uneven coating. 12. The recommended spray distance is 150-200 mm (6”-8”). 13. Spray edges first. Overlap each stroke a minimum of 50%. Move gun at a constant speed. 14. Always turn off air supply and relieve pressure when gun is not in use. EE

8 clean and free from damage. Build up of dried paint can distort the spray pattern. 6. Lubrication – stud/screw (6), needle (9) and air valve (11) should be oiled each day. Replacement of Parts EE Nozzle (2) and Needle (9) – Remove parts in the following order: 7, 8, 9, 1 and 2. Replace any worn or damaged parts and re-assemble in reverse order. Recommended tightening torque for nozzle (2) 9.5-12 Nm (80-100 lbf in). Packing – Remove parts 7, 8, 9. Unscrew cartridge (4). Fit new cartridge finger tight. Re-assemble parts 9, 8, and 7 and tighten cartridge (4) with spanner sufficient to seal but to allow free movement of needle. Lubricate with gun oil. Air Valve Seal Kit (16) - (Refer to photos 1 to 28 and fig 2) 1. Remove Adjusting Knob (7), Spring (8), and Needle (9). 2. Loosen Housing (10). 3. Remove Housing (10) and Airvalve Spring. 4. Remove Valve (11). 5. Using Service Tool SPN-7, engage groove behind the Valve Seat. 6. Remove Valve Seat. 7. Push out the Front Airvalve Seal with a finger. 8. Turn the Gun upside down and let the Seal fall out. 9. Fit New Front Seal to Service Tool. 10. Fit new Seal to gunbody and press firmly to ensure Seal is engaged. 11. Fit New Valve Seat to Service Tool. Groove must face outwards. 12. Fit Valve Seat to Gunbody. 13. Remove Rear Airvalve Seal from housing (10) with a hooked instrument. 14. Fit new Seal to Service Tool. 15. Fit Seal to Housing (10). 16. Replace Valve (11). 17. Replace Valve Spring and screw in Housing (10). 18. Tighten Housing. 19. Fit Needle (9). 20. Fit Spring (8) and Knob (7). 21. Adjust Needle Packing (4) with Spanner sufficient to seal but to allow free movement of needle. Lubricate with gun oil. Spreader valve (5) – Caution: always ensure that the valve is in the fully open position by turning screw fully counter- clockwise before fitting to body. Air cap / Nozzle Selection Refer to coating material manufacturers recommendations or ITW Finishing UK Website: www.itweuropeanfinishing.com FIG 2

11 17 18 19 20 21 16 Accessories Spanner – order SPN-5 Cleaning Brush – order 4900-5-1-K3 Regulator/Gauge Attachment - order HAV-501-B Pressure gauge Attachment – order GA-515 Gun Mounted Regulator – order DVR-501 Spraygun Lubricant - order GL-1-K10

12 Roundspray Aircap - COM-500R HVLP Mode - Air Inlet Pressure = 1.0 Bar (14.5 PSI) Tanstech Mode – Air Inlet Pressure = 2 bar (29 PSI) Approx Spot Size = Ø50mm ITW Finishing Systems and Products Ringwood Road, Bournemouth, BH11 9LH, England. Tel. No. (01202) 571111 Telefax No. (01202) 581940, Website address http://www.itweuropeanfinishing.com ITW Finishing Systems and Products is a Division of ITW Ltd. Reg. Office: Admiral House, St Leonard’s Road, Windsor, Berkshire, SL4 3BL, UK Registered in England: No 559693 Vat No 619 5461 24