CATSKILL 7222 Assembly Instructions Manual

Text of CATSKILL 7222 Assembly Instructions Manual

Drop Leaf Cabinet Cart

GENERAL: 1. You have purchased model 7222. Overall dimensions of an assembled unit is 40” x 20” x 34.25” when drop leaves are up. 2. Should you need assistance or need to replace a damaged or missing part, DO NOT RETURN THE UNIT TO THE STORE where you purchased it, simply give us a call at 607-652-7321 from 7:30 - 4:00 PM Eastern time and we’ll send you the prepaid part via UPS usually that sa

Top Front Brace (1)

P/N B-15 7/8-1 1/4-TF B2 Top Back Brace (1) P/N B-15 7/8-5 3/8-TB B3 Bottom Front/Bottom Back Brace (2) P/N B-15 7/8-2-BFBBTB B4 Middle Back Brace (1) P/N B-15 7/8-2-MB B5 Middle Front Brace (1) P/N B-15 7/8-2-MF BP Back Panel (1) P/N BP-7222 15 13/16-15 1/16 D1 Drawer Front (1) P/N DF-7221 15 11/16-3 7/8 D2 Drawer Back (1) P/N DBK-7221/L 13 3/8-3 D3 Drawer Side/Left (1) P/N DS-7221/L 14 7/8-3 D4 Drawer Side/Right (1) P

1 3/4” Phillips Flat Head Bolt (12)

1 1/4” Phillips Flat Head #8 Screw (8) 3/4” Truss Head Machine Screw (6) 5/8” #6 Pan Head Screw (2) 5/8” Phillips Flat Head #8 Screw (12) 3/4” Long 3/16” DIA. Steel Pin (14) 1” Long 3/16” DIA. Steel Pin (8) 1 1/2” Long 3/16” DIA. Steel Pin (4) Hinge (4) Caster Socket (4) Wheel Casters (2) Locking Wheel Casters (2) Magnet Plate (1) Magnet (1) 3/16” Flat Washer (2) 10-24 Hex Nut (12

1. The Bastion fastening system consists of a steel post (threaded on one end with a

hole through the shaft on the other end); a Barrel Nut (cylindrical barrel-shaped with threaded open end & holes through the sides); and a Set Screw (Phillips slot on one end, pointed on the other) 2. To attach Posts: A) Dip threads of Post in vegetable oil. B) Align threaded end of Post with hole in wood, tap on slotted end with hard hammer until threads enter, the

Tap in post with a hammer to start and screw down with a screwdriver or with a small allen wrench

until the shoulder of the post hits the wood. Then unscrew until the hole is parallel with the groove on the bottom of the Drawer Front. To understand how the bastion fastening system works see “Tips on how the Bastion System Works” or visit www.catskillcraftsmen.com and click on our instructional video. Either D1 1 1/4” #8 1” Ma

The glides look almost alike

however, they are labeled CR for Cabinet Right and CL for Cabinet Left. SP 5/8” #6 1 1/4” #8 G1 SP G1 Left Side Right Side STEP 4 Brace Preparation B4 B3 BP B2 3/4” Pin B5 B3 1” Pin Note: Ok if pins are loose

TIP: Place the nut on the tip of your finger

and hold it against the inside of the hole as you screw in the bolt from the other side. Step 6 Door Assembly 1/2” #4 RD 5/8” #8 1 1/2” Pin LD DS INSIDE VIEW OF DOORS B4 BP B3 B2 Nut SP SP 1 3/4” Machine Screws Side Panel Leg Inside Brace Countersunk Hole in Leg ( disk goes in this hole to hide bolt head! ) Nut Access Hole Hex Nut B4 BP B3 SP Side Panel Leg Inside Brace Countersunk H

1 3/4” Machine Screws

B5 B1 Step 8 Door Magnet 1. Stick magnet to magnet plate on right door. 2. With left door open, close the right door. The magnet should be positioned over the wooden block on the bottom of the top front brace. Hold the magnet in place with your thumb, and open the right door. The magnet will be in the correct position on the block. Mark holes with pencil thru slots, make pil

1 3/4” #8

SP SP Invert the Cart Base and posi- tion onto the Cart top. Fit the “Z” brackets into the slot across the top back brace. Align the holes in the top front brace with the pilot holes at the front of the cart top. Attach the top front brace to the cart top with 1-3/4” #8 Wood Screws. Tighten the “Z” brackets to complete top attachment with 5/8” #8 screw. NOTE: The holes for the “Z” brackets are further apart than tho

CATSKILL Indoor Furnishing Owners Instructions: