Benelli BJ250 Operation & User’s Manual

Preface ................ ...

Tool Bag ....................................................................................................................................................................................................... Notice of Use of ...

Bulb Replacemen ...

specifcations of fuses are not allowed to use, especially the electric wires which would result severe damages to other parts, even fre accidents. Location of fuse: beside the battery. Burnt fuse is usually caused by the internal circuit fault of the motorcycle. Simply estimate the whole situation of the motorcycle ...

The very beginning 1,000km driving-way of the motorcycle is the most important part of its service life. If the running in is carried normally, a longest service life can be assured and the performances of the new motorcycle can be fully fulflled. PREFACE Thanks for choosing Benelli motorcycle, which is combined with international advanced technologies and ...

here to indicate the importance degrees, please make sure that you have fully understand the meanings as following: Alarm------------ This is for the important procedures that may endanger safety of the driver and would bring injuries if ignored. Caution------------ This is for the relative operation specifcations of the motorcycle ...

2. Many accidents happen due to inexperienced driver. Make sure the driver is qualifed before driving the motorcycle. Never give it to any people without a driving license. 3. Most of the crashes between cars and motorcycles are caused by the car drivers' "not seeing" the motorcycle drivers. In order to avoid accidents, the dri ...

driver should wear a safety helmet, and also motorcycle boots, gloves and protection clothes. The passenger shall also wear the same. 2. The exhaust pipe will be very hot during driving and the heat will last after turning of the engine. Never touch the mufer and wear those clothes that can totally cover the legs ...

can also make sure that the dealer would provide you better services involving accessories purchasing or other services. Record the numbers for the possible use in the future. Vehicle identifcation number (VIN) is printed on the right side of the head tube. The engine number is printed on lower part of the right case of e ...

Left view Right view C 1 2 3 4 6 7 5 1 Clutch lever 2 Left handle switch 3 ABS switch(if equipped) 4 Meter 6 Throttle grip 5 Right handle switch Rear shock absorber Rear brake pedal Shift pedal 11 Side stand 12 Tank 8 9 10 Front brake lever 7 10 12 11 9 8 ...

1.TURNING INDICATOR The indication lamps would fash with the turning signals. 2. GEAR INDICATOR LAMP Numbers on the meter indicate the gear positions of the vehicle including 1, 2, 3, 4, 5 and6. 3. TACHOMETER Tachometer indicates the revolution per minute of engine. 4. NEUTRAL INDICATOR LAMP When the transmission is in the neutral, the indicator lamp would be on. 5. ODOMETER/ TRIP METER Odometer records the total mileage driven, ...

15. ABS INDICATOR LIGHT(IF EQUIPPED) 1. ABS failure -- If any type of ABS failure is detected and stored, ABS indicator light is lit and stays on after repaired, then ABS indicator light will be unlit after the next Power switch ON/OFF and when vehicle speed exceeds 5km/h. 2. ABS is under OFF mode --ABS indicator light Blink 1 time/1.27s(Slow Blink) 3. When press the the ABS switch within 3s ~30s --ABS indicator light Blink 1 ...

is not necessary and is also apt to cause accident. Press the key in a proper force. P U S H KEY SWITCH “ ”position: The circuits are on “ ”Position: turn left to the maximum, press the key to the position of “ ”. Take out the key. In this condition, the vehicle has been locked. If you want to unlock the vehicle, insert the key a ...

Press down on the button,to activate the horn. 2. HIGH & LOW BEAM SWITCH Turn the switch to " " position, the high beam of headlamp turn on and the indicator lamp on the meter would also turn on; turn the switch to " " position, the low beam of headlamp turn on. 3. DIRECTION INDICATOR LAMP SWITCH Turn the switch to " " position, the left direction signal lamp fashes; turn the switch to " " po ...

If you want to enable/disable the ABS , please keep you motorcycle slower than5km/h or stop, because the ABS switch only works when vehicle speed is lower than 5km/h. 5 ABS From ABS ON mode → OFF mode Please Keep pressing the ABS switch precisely within the range of 3~5 sec- onds, the ABS indicator light should be changed from lit to blink as per 1.27s (Slow Blink) when you release the switch,Now ...

system If you keep pressing the ABS switch within 5s~30s. ABS will keep the current mode. The ABS will be changed to ON mode from any other mode if the switch was stuck or pressed more than 30s. ABS is designed to help prevent the wheels from locking up when the brakes are applied hard while running straight. The ABS automatically regulates brake force Intermittently, gaining grippin ...

manner as conventional vehicle brake system. • ABS cannot compensate for adverse road conditions, misjudgment or improper application of brakes. You must take the same care as with vehicles not equipped with ABS. • ABS is not designed to shorten the braking distance. On unpaved, uneven, or downhill surfaces, ...

can afect wheel speed, they may confuse the computers, which can extend braking distance. Use of non-recommended tires may cause malfunctioning of ABS and can lead to extended braking distance. The rider could have an accident as a result. Always use recommended standard tires for this vehicle. WARNING ! ○ ABS in ...