Xerox WorkCentre Pro 128 Install Manual

Xerox DocuTech 128/155/180 HighLight Color 701P46159 October 2006 The main DocuTech 128/155/180 HLC components are: • Sun Blade TM 2500 Controller • CD/DVD combo drive • color flat panel monitor • keyboard and mouse • Ethernet interface (10/100/1000 BaseT) • Three printer interface cards • Controller Stand • Options • 18/36 track tape drive • Online connection • QIC tape • USB floppy disk drive or • Sun W1100Z (AMD) contoller • CD/DVD combo drive • color flat panel monitor • keyboard and mouse • Ethernet interface (10/100/1000 BaseT) • Three printer interface cards • Controller Stand • Options • 18/36 track tape drive • Online connection • QIC tape • USB floppy disk drive • Solaris 10 and DocuSP print services software • Printer • Black plus one highlight color* • Xerographic engine with laser raster imaging system for black and Light Emitting Diode for color • Permanent housing for black dry ink; customer changeable unit (CCU) for color dry ink • Prints simplex or duplex • Inverter Feeder/Stacker and up to 3 additional feeder/stackers • Optional Bypass Transport to provide connection to additional finishers * Additional dry inks, not listed on this document, will be customer options as they become available, and will be offered under standard Xerox terms and conditions. Space Requirements / Service Space Envelope The dimensions shown below are absolute minimums. Configuration Width Depth Min total req’d Width x depth Weight With inverter feeder/stacker and one feeder/stacker 173.3 (in) 433.3 (cm) 48.8 (in) 122 (cm) 262.5 x 131.5 (in) 631.3 x 328.8 (cm) 3164 lbs 1438 kg With inverter feeder/stacker and two feeder stackers 205.6 (in) 511.3 (cm) 48.8 (in) 122 (cm) 294.8 x 131.5 (in) 737 x 328.8 (cm) 3685 lbs 1675 kg With inverter feeder/stacker and three feeder/stackers 237.9 (in) 594.4 (cm) 48.8 (in) 122 (cm) 327.1x 131.5 (in) 817.8 x 328.8 (cm) 4206 lbs 1912 kg Optional Bypass Transport* 20.4 (in) 51 (cm) 28.3 (in) 71 (cm) 176 lbs 80 kg • The minimum total space required includes the required space necessary for the Xerox service personnel to service the printer. • A minimum of 78 inches/198 cm clearance from the floor to the nearest overhead obstruction must be maintained. • The printing system must be installed in a fixed location. • Space requirements for the controller stand are 36 x 36 inches/91 x 91 cm. • For proper operation, the printer must be perfectly level. On floors less than two degrees out of level, a leveling kit must be used to level the equipment. The printer will not function properly on floors more than two degrees out of level. • For detailed space requirements and diagrams, refer to the DocuTech 128/155/180 HighLight Color Installation Planning Guide. Electrical Requirements (printer) The printer requires: • 60 HZ service (2 cords required) MultiSource 2-phase, dual power cord configuration Voltage 208/240(4 wire) 208/240 (4 wire) Amperage (dedicated) 50 30 Cycles 60 Hz 60 Hz Receptacle Xerox Part No. Receptacle NEMA Part No. 14-50R 14-30R Receptacle Diagram Power Cord Kit Number Power Cord Length 15 feet 15 feet

Xerox DocuTech 128/155/180 HighLight Color 701P46159 October 2006 • 50 Hz service • 30 amp dedicated service (WYE): 220/380 VAC or 230/400 VAC or 240/415 VAC (3 phase) Agency certifications: UL, cUL, CE Mark, FCC Electrical Requirements (Controller) The Controller requires 20 AMP dedicated service. The information for the 20 Amp electrical service is identified below. Controller 36 Track Tape (Optional) Line Options Dedicated Dedicated Voltage 115vac 115vac Amperage 20 20 Cycles 60 Hz 60 Hz Xerox Receptacle Part No. 600S3703 600S3703 Receptacle NEMA Part No. 5-20R 5-20R Power Cord Xerox Part No. 98K19950 98K19950 Receptacle Diagram 97S02370 97S02370 Installation Considerations 1. DocuTech HLC printers built in 2004 may require specific delivery cooperation between the Xerox Service Representative and the delivering Rigger for any doorway or hall that is smaller than 37 inches. Please ensure that Xerox Service is informed during the preinstallation planning process if any opening through which the printer is to be moved is smaller than 37 inches. 2. Dedicated service is required for each component. 3. The controller can be connected to a 15 amp or 20 amp outlet. 4. The length of the cable from the controller to the printer is 16 feet (4.8 metres). 5. Do not use an adapter to connect the controller to an electrical outlet that lacks a ground connection terminal. 6. The customer is responsible for providing the network and the client workstation(s). The Ethernet interface on the DocuSP controller is a auto-sensing 10/100/1000 - MB/sec twisted pair standard (BaseT). 7. The Ethernet connection to the DocuSP controller must be compatible with the Institute of Electrical and Electronics Engineers (IEEE) 802.3 standard. Paper Handling • 16 to 110 lb. (60 to 200 gsm) cut sheet paper weights • 8 by 10 in. to 14 x 17 in. (203 by 254 mm to 356 by 432 mm) including A4, A3, and B4 paper sizes • 7 by 10 in. (178 by 254 mm) optional enablement kit • Transparencies, label stock, tab stock, carbonless paper, pre- perforated stock • Paper stock weights less than 16 lb. are not recommended. • Textured stocks are not recommended. • Some 65 lb. stocks may not fully fuse. Input Tray Capacity Main tray (tray 1) 1,100 sheets 20 lb (75 gsm) Auxiliary tray (tray 2) 600 sheets 20 lb (75 gsm) High capacity feeders (trays 3 and 4) 2,600 sheets each 20 lb (75 gsm) Additional high capacity feeders (up to two optional) 2,600 sheets each 20 lb (75 gsm) Output Tray Capacity Two high-capacity stackers 2,500 sheets each 20 lb (75 gsm) Sample tray 100 sheets 20 lb (75 gsm) Purge tray 100 sheets 20 lb (75 gsm) Environmental Requirements Temperature 50 to 85 o F (10 o to 29 o C) Humidity Non-condensation 30 to 65% RH Heat Emission - printer 4454 BTU/Hr (Standby) 32,770 BTU/Hr (Operating) Altitude (above sea level) Up to 6,000 ft (1830 m) Operating Supplies Reorder No. Dry Ink - Black 6R206 (US/CA) Dry Ink – Blue 6R1191 (US/CA) 6R90343 (XE) Dry Ink – Red 6R1192 (US/CA) 6R90344 (EU) Dry Ink – Green 6R1193 (US/CA) 6R90345 (EU) Dry Ink – Royal Blue 6R1255 (US/CA) 6R90356 (XE) Dry Ink – Cardinal Red 6R1277(US/CA) 6R90358(XE) Dry Ink – Cyan 6R1284(US/CA) 6R90359(XE) Dry Ink – Magenta 6R1296 (US/CA) 6R90360 (XE) Dry Ink – Yellow* 6R1299 (US/CA) 6R90361 (XE) Developer (Black, Red, Blue, Green, Royal Blue, Cardinal Red, Cyan, Magenta, Yellow) NA Fuser Blend 8R12938 (1 bottle) 8R12939 (6 bottles) Fuser Shield 8R4077 (1 bottle) 8R7618 (6 bottles) Dry ink waste container 93K1393 HLC developer waste bottle 604K24870 (4 bottles) * Will be available in the near future.

Xerox DocuTech 128/155/180 HighLight Color 701P46159 October 2006 NOTE: The formula for the DocuTech HLC fuser lubricant was changed in 2006 to provide better image quality and to prevent image transfer. The new fuser formula is called Fuser Shield. The Fuser Blend and the Fuser Shield CANNOT be intermixed in a DocuTech HLC. To change from one fuser lubricant to another requires a service call and cleaning or replacing components. The two fuser formulas are identified with different color bottles and caps. PDL Compatibility The system interprets the following data streams: • PostScript Level 3 • HP PCL5c / HP PCL6 • ASCII • PDF • TIFF If a machine is running with in-line finishing equipment, the new Fuser Shield may contribute to poor binding at the binder glue seam. Customers experiencing this problem can have their equipment returned to using Fuser Blend by placing a service call to clean and/or replace components. Do NOT place Fuser Blend in a machine that has been using Fuser Shield. • VIPP • PPML • LCDS/Metacode and IPDS will be customer options which may be acquired as they become available, and will be offered under standard Xerox terms and conditions. Printing Considerations • Monthly duty cycle is up to 4 million (DT 128 HLC), 4.5 million (DT 155 HLC) or 6 million (DT 180 HLC). Not all features and capabilities are available with every print driver and OS/Protocol combination. Custom software applications may produce unexpected results. • The Xerox Supplies Marketing Center, 1-800-822-2200, is available for ordering Xerox supplies, including paper and other throughput material. Other Considerations • The Dry ink waste container supply is maintained at the customer site by the Xerox Service Representative and is not orderable by the customer. • The Xerox Welcome Center at 1-800-821-2797 is available to provide customer support. Network Connectivity The DT 1xx HLC supports the following connectivity: Network Operating System Protocol Topology Novell 3.x / 4.x (NDS or Bindery mode) IPX / SPX Ethernet Windows NT 4.0 / Win2000 / WinXP TCP / IP LPR Ethernet / Token Ring AppleTalk EtherTalk Ethernet LPD Server (Unix Systems) TCP / IP Ethernet / Token Ring Online Channel IBM 3211/4245 Ethernet / Token Ring Bus and Tag NOTE: Token Ring is not available for AppleTalk or Novell environments. The system supports Port Printing, and HTTP and IPP Printing modes. Additionally, SNMP Services and DocuSP Remote Workflow can be enabled on the customer’s network. Print Drivers - Environments The DT 1xx HLC supports the following print drivers: • Windows 95/98/ME/2000/XP • Windows NT 4.0 • MAC OS 8.6 & higher • Solaris 2.8 Additional Optional Interface Requirements Online – Bus and Tag supporting IBM 3211/4245 interface.