360 Vision Eclipse HD Stainless Steel Installation & Configuration Manual

Page 1 © 360 Vision Technology Ltd. Eclipse HD Stainless Steel Installation/Configuration Manual ...

Page 2 © 360 Vision Technology Ltd. Table of Contents 1 Safety and Precautions .............................................................................................................................. 3 2 Housing Dimensional Drawing ................................................................................................................... 3 3 Connection .................................................................... ...

Page 3 1 Safety and Precautions 1. Please read these notes before attempting to operate the 360 Vision Eclipse HD Stainless Steel, and keep for future reference. 2. DO NOT disassemble or remove covers. This will break the water seals and invalidate the warranty. 3. All servicing and repairs must be handled by 360 Vision Technology. 4. Avoid pointing the camera directly towards a bright light source (sunlight), or expose the camera to ...

Page 4 © 360 Vision Technology Ltd. 3 Connection MAINS FUSE PRED-PSU-SM-WA-HD MAINS FUSE 3 = 2AF OUTPUT FUSE PRED-PSU-SM-WA-HD FUSE 1 = 6.3AT FUSE 2 = 1AT FUSE 4 = 1AT MAINS input 100 - 240Vac Io Vo Adj Adj Model Number: PRED-PSU-SM-WA-HD Serial Number: yymmndd-xxxx Input Voltage:100-240VAC 50/60Hz Input current 2.1A Output Voltage: 30V DC Output Current: 6.2A PRED-PSU-SM-WA-HD 255 x 180 x 100mm Enclosure Dimensions 360 USE 3 ...

Page 5 © 360 Vision Technology Ltd. The Ethernet connection uses standard CAT5, CAT5e or CAT6 cables fitted with RJ45 connectors. RJ45 CAT5, CAT5e, CAT6 Cable Signal Pin 1 White with Orange Band Tx+ Pin 2 Orange Tx- Pin 3 White with Green Band Rx+ Pin 4 Blue Pin 5 White with Blue Band Pin 6 Green Rx- Pin 7 White with Brown Band Pin 8 Brown The power connection is supplied as a standard length of 2m cable (red/black) • 24Vdc - 36Vdc ...

Page 6 © 360 Vision Technology Ltd. Eclipse HD Stainless Steel Configuration 4 Locating the Eclipse HD on your Network Default IP Address 192.168.1.187 Subnet 255.255.255.0 Gateway 192.168.1.4 Using the DVR management software, ‘Onvif Device Manager’ or 360 Vision Discovery Tool (which can be found on the CD supplied or from the 360 Vision Technology technical support) to find the IP address of the Eclipse HD. Note the ports used ...

Page 7 © 360 Vision Technology Ltd. Enter the User Name (default is admin) Enter the Password (default is 9999) If you select the box ‘Remember Password’ it could compromise the security of the Eclipse HD camera. Select Submit The camera web page uses VLC as the video player. VLC video plug-in file can be downloaded from the camera if it is not installed on the connecting PC/laptop (See Browser - page 24) ! ...

Page 8 © 360 Vision Technology Ltd. There are six main tabs on the left of the web page/screen. 1 Live View 2 Settings 3 Add/Edit Users 4 Maintenance 5 Browser 6 Logout 5.1 Live View 5.1.1 Live Video The Live Video page offers options to:- • Stream - Choose required stream from drop down selection. • 1x Display - Use to show selected stream as full screen. • Zoom In/Out - This will operate the optical and digital zoom (if digit ...

Page 9 © 360 Vision Technology Ltd. 5.1.2 Status Status page shows information relating to the camera status. Status page, top section. Status page, bottom section. ...

Page 10 © 360 Vision Technology Ltd. • Save - Used to save the status page information as a HTML file. • Refresh - Select an automatic page refresh option. • Camera - Shows information relating to the camera time & date settings, the version of codec and mainboard software loaded • Video Streams - Shows the current video streams configuration. • Streaming - Shows the IP address on the PC that is receiving the video streams. ...

Page 11 © 360 Vision Technology Ltd. 5.2 Settings 5.2.1 Video The Video page, offers options to setup:- • Camera - Add or edit the camera name. • Stream Type - Choice of single or dual video streams. • Codec - Choose which compression format, the stream will use. (See page 27 for table of options). • Resolution - Set what resolution the stream will use. (See page 27 for table of options). Stream Tabs, offer options to:- • F ...

Page 12 © 360 Vision Technology Ltd. RTSP URL • Copy - Use this option to copy the RTSP URL • Date Position - Choose date text to bottom right or left of the image. • Time Position - Choose time text to bottom right or left of the image. • Show Sub-stream - Shows second sub-stream if enabled. OK to program the new settings into the Eclipse HD. Cancel to abandon the changes to the video settings. 5.2.2 Video Advanced Multicast ...

Page 13 © 360 Vision Technology Ltd. Multicast If the receivers of the video streams are suitable for using ‘multicast’ and the video streams will all have the same format, then it may be possible to use ‘multicast’. In this mode, the CODEC in the Eclipse HD chooses a ‘new UDP address’ (Typically an address which is outside the normal range of addresses for the network to which the Eclipse HD is connected) and sends a vid ...

Page 14 © 360 Vision Technology Ltd. 5.2.3 Advanced Features The Advanced Features page, offers options to:- • Camera - Cannot be edited, shows label/name given to the camera. (See Video - Camera - page 11). A ‘Preset’ is a stored view. When a preset is defined, it will store the zoom, focus and iris positions. Presets Set Preset using the following options:- • Number - Choose from a list of presets using the drop down box. � ...

Page 15 © 360 Vision Technology Ltd. Wiper • Rest Time - Set wiper rest time. • On Time - Set time period for how long wiper will run. Home Function The camera will perform an action (goto preset), after a period of inactivity. • Home Action - This sends the camera to a preset. • Home Number - This sets the preset the camera will go to/start. • Home Timer - This sets the time for the period of inactivity. Zoom ratio is also ...

Page 16 © 360 Vision Technology Ltd. 5.2.4 Camera • Camera - Cannot be edited, shows label/name given to the camera. (See Video - Camera - page 11). The Camera page, offers options to:- Camera Settings • Digital Zoom - Enable digital zoom. Default is off. • White Balance - Select White Balance settings to suit camera location. (See page 29 for table of options). • Wide Dynamic range - Enable WDR. Options available are ON, Aut ...

Page 17 © 360 Vision Technology Ltd. Steady Shot – The viewed picture is made from a window which shows part of the full picture from the camera sensor. This means that part of the picture is wasted. The viewed part of the picture is moved automatically to use some of the wasted part so that the observed picture is stable and has compensated for the vibrations and minor movements of the Eclipse HD. The maximum amount of picture sta ...

Page 18 © 360 Vision Technology Ltd. 5.2.5 Date/Time • Camera - Cannot be edited, shows label/name given to the camera. (See Video - Camera - page 11). • Camera Time - Cannot be edited, shows the current date and time of the camera. • Date Format - Select from the drop down the date format. • Time Format - Choose 24hr or 12hr time display. Set Time The Date/Time page, offers options to:- • Set Manually - Input time/date man ...

Page 19 5.2.6 Network • Camera - Cannot be edited, shows label/name given to the camera. (See Video - Camera - page 11). Network The Network tab, offers options to:- • DHCP Enable - Allows the camera to be set using a dynamic IP address. • IP Address - Input a static IP address, if DHCP is not used. • Netmask - Input the Network Subnet Mask. • Default Gateway - Input the Network Gateway. • Primary Name Server - Input the D ...

Page 20 © 360 Vision Technology Ltd. 5.2.7 Interfaces Auxiliary Functions Allows the camera to be configured to use Onvif Auxiliary commands. Features available are:- • Force White Light On - Forces white lights on. • Force White Light Off - Switches off forced white lights. • Wiper On - Activates wiper. • Wiper Off - Stops wiper. • Dark IR Light On - Switch on IR, when dark. • Dark White Light On -Switch on white light, ...