Biostar TFORCE 550 Operation & User’s Manual

Text of Biostar TFORCE 550 Operation & User’s Manual

TForce 550 Setup Manual

FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmf

Table of Contents

Chapter 1: Introduction.......................................... 1 1.1 Before You Start ................................................................................1 1.2 Package Checklist.............................................................................1 1.3 Motherboard Features......................................................................2 1.4 Rear Panel Connectors .................................................

CHAPTER 1: INTRODUCTION

1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: „ Prepare a dry and stable working environment with sufficient lighting. „ Always disconnect the computer from power outlet before operation. „ Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded applian

AMD Athlon 64 / Athlon 64 FX / Sempron

processors AMD 64 Architecture enables 32 and 64 bit computing Supports Hyper Transport and Cool=n=Quiet FSB Support HyperTransport Support up to 1000 MHz Bandwidth Chipset nVIDIA nForce 550 Super I/O ITE 8712F Provides the most commonly used legacy Super I/O functionality. Low Pin Count Interface Environment Control initiatives, H/W Monitor Fan Speed C

Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supply Power Connector (4pin) x1 Connects to Power supply Back Panel I/O PS/2 Keyboard x1 PS/2 Mouse x1 Serial Port x1 LAN port x1 USB Port x6 Audio Jack x6 Connects to PS/2 Keyboard Connects to PS/2 Mouse Provide RS-232 Serial connection Connects to RJ-45 ethernet cable Connects to USB devices Provide Audio-In/Out and microphone

CHAPTER 2: HARDWARE INSTALLATION

2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Step 1: Remove the socket protection cap. Step 2: Pull the lever toward direction A from the socket and then raise the lever up to a 90-degree angle. Step 3: Look for the white triangle on socket, and the gold triangle on CPU should point forwards this white triangle. The CPU will fit only in the correct orientation.

Step 4: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation. Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN power cable to the JCFAN1. This completes the installation. 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while m

JSFAN1/JSFAN2: System Fan Header

JSFAN1 Pin Assignment 1 Ground 2 Smart Fan Control 3 FAN RPM rate sense JSFAN2 Pin Assignment 1 Ground 2 +12V 1 3 1 3 JSFAN2 JSFAN1 3 NC JNFAN1: North Bridge Fan Header Pin Assignment 1 Ground 2 +12V 3 1 JNFAN1 3 FAN RPM rate sense Note: The JSFAN1/JSFAN2 and JNFAN1 support 3-pin head connector. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to

INSTALLING SYSTEM MEMORY

DDR2A1 DDR2B1 DDR2B2 DDR2A2 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated. B. Memory Capacity DIMM Socket Location DDR/DDR2 Module Total Memory Size DDR2A1 256MB/512MB/1GB *1

Biostar Motherboard Owners Instructions: