ABB REU615 Manual 

Issued: 2013-02-21 Revision: C Product version: 4.0 FP1 © Copyright 2013 ABB. All rights reserved ...

permission from ABB, and the contents thereof must not be imparted to a third party, nor used for any unauthorized purpose. The software or hardware described in this document is furnished under a license and may be used, copied, or disclosed only in accordance with the terms of such license. Trademarks ABB and Relion are registered trademarks of the ABB Group. All o ...

or product description and are not to be deemed as a statement of guaranteed properties. All persons responsible for applying the equipment addressed in this manual must satisfy themselves that each intended application is suitable and acceptable, including that any applicable safety or other operational requirements are complied with. In particular, any risks in ...

Communities on the approximation of the laws of the Member States relating to electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB in accordance with the product standards EN 50263 and EN 60255-26 for the ...

Section 1 Introduction.......................................................................7 This manual........................................................................................7 Intended audience..............................................................................7 Product documentation.......................................................................7 Product documentation set.............................. ...

LD0.TRPPTRC1 Global conditioning (1)................................20 LD0.TRPPTRC2 Global conditioning (2)................................21 LD0.FRPFRQ1 Frequency protection (1)...............................21 LD0.FRPFRQ2 Frequency protection (2)...............................21 LD0.FRPFRQ3 Frequency protection (3)...............................21 LD0.FRPFRQ4 Frequency protection (4).. ...

Generic functions.........................................................................29 LD0.MAPGAPC1 Multipurpose analog protection function (1).............................................................................29 LD0.MAPGAPC2 Multipurpose analog protection function (2).............................................................................29 LD0.MAPGAPC3 Multipurp ...

LD0.SPCGGIO2 Multipurpose binary outputs (2)..................37 LD0.SRGAPC1 Multipurpose binary outputs - flip-flop resets (1)................................................................................38 LD0.SRGAPC2 Multipurpose binary outputs - flip-flop resets (2).............................. ...

Protection-related functions.........................................................45 DR.RDRE1 Disturbance recorder values...............................45 LD0.SECRSYN1 Synchrocheck line and bus state................45 Generic functions................................................................. ...

specific to the IED. The manual should be used in conjunction with the corresponding communication protocol manual. 1.2 Intended audience This manual addresses the communication system engineer or system integrator responsible for pre-engineering and engineering for communication setup in a substation from an IED perspective. The system engi ...

functions as well as communication engineering for IEC 61850 and other supported protocols. The installation manual contains instructions on how to install the IED. The manual provides procedures for mechanical and electrical installation. The chapters are organized in chronological order in which the IED should be installed. The operation manual contains instructions on how to ...

1.4.1 Symbols The caution icon indicates important information or warning related to the concept discussed in the text. It might indicate the presence of a hazard which could result in corruption of software or damage to equipment or property. The information icon alerts the reader of important facts and conditions. The tip icon indicates advice on, for example, how to design your project or how to use a certain function. Althou ...

Table 1: REU615 functions, codes and symbols Function IEC 61850 IEC 60617 IEC-ANSI Protection Three-phase non-directional overcurrent protection, low stage PHLPTOC1 3I> (1) 51P-1 (1) Three-phase non-directional overcurrent protection, high stage PHHPTOC1 3I>> (1) 51P-2 (1) Three-phase non-directional overcurrent protection, instantaneous stage PHIPTOC1 3I>>> (1) 50P/51P (1) Residual overvoltage protection ROVPTOV1 Uo> (1) ...

LSHDPFRQ1 UFLS/R (1) 81LSH (1) LSHDPFRQ2 UFLS/R (2) 81LSH (2) LSHDPFRQ3 UFLS/R (3) 81LSH (3) LSHDPFRQ4 UFLS/R (4) 81LSH (4) LSHDPFRQ5 UFLS/R (5) 81LSH (5) Control Circuit-breaker control CBXCBR1 I <-> O CB I <-> O CB ...

2.1 Overview This document describes the DNP3 data points and structures available in the IED. The data points are unmapped as a default on the DNP3 level. The point lists describe a superset of all DNP3 data available through the standard configuration/s including the optional functionalities. The point tables show all the available DNP3 data points in the IEDs. The data objects in the point tables are listed based on the AFL ...

Function block UE01 UE02 PSPTUV2 ● NSPTOV1 ● NSPTOV2 ● FRPFRQ1 ● FRPFRQ2 ● FRPFRQ3 ● FRPFRQ4 ● FRPFRQ5 ● FRPFRQ6 ● T2PTTR1 ● TRPPTRC1 ● ● TRPPTRC2 ● ● ARCSARC1 o ARCSARC2 o ARCSARC3 o MAPGAPC1 o MAPGAPC2 o MAPGAPC3 o MAPGAPC4 o MAPGAPC5 o MAPGAPC6 o LSHDPFRQ1 ● LSHDPFRQ2 ● LSHDPFRQ3 ● LSHDPFRQ4 ● LSHDPFRQ5 ● CBXCBR1 ● ● DCXSWI1 ● ● DCXSWI2 ● ● ESXSWI1 ● ● DCSXSWI1 ● ● DCSXSWI2 ● ● DCSXSWI3 ● � ...