Caliber CALNAV Owner's Manual

INSTALLATION............................................................................................................5 VIEWS ..........................................................................................................................9 Front View...............................................................................................................9 Back View .............................................................................................................10 Bottom View ..................................... ...

follow all the instructions given. This will help to ensure reliable operation and extend the service life of your device. Keep the packaging and the user instructions for future reference or inquiries. If you pass the article on to another person, you must pass on these instructions, too. • Never open up the housing of the device or the AC adaptor. These do not contain any serviceable parts. If the housing is opened there will be danger to life from electric shock. • Do not place any objects on the device and do not exert any pressure on the display. Otherwise there is a danger that th ...

• Warning: Danger of explosion if rechargeable batteries are not charged properly. • Batteries cannot withstand heat. Avoid the device and the integrated battery becoming overheated. Failure to comply with this instruction may lead to damage to and even explosion of the battery. • Only use either the original AC adaptor or the car adaptor from the optional navigation kit to charge the battery. • The batteries are special category waste. When disposing of the device ensure that this is done correctly. For more details, please contact customer service. Care of the Display • Avoid scratching the d ...

by step through the initial setup of the navigation system. Firstly, remove the foil for protecting the device during transportation from the display. Switch on the navigation system. Set the battery switch (15) on the bottom of the device to the ON position. Attention: Always leave the battery switch on the ON position, unless you want to perform a new reinstallation. If the switch is set to the OFF position, all data will be lost and you will have to perform the initial installation again. The initial installation of the navigation system is started automatically. The brand logo appears and after a few seco ...

• Your device only supports memory cards in the FAT16/32 file format. If you insert a card formatted with a different format (e.g. in cameras, MP3 players), your navigation system may not recognise it and will ask you to format it again. Warning: Formatting the memory card irretrievably wipes out all data. • Likewise you cannot just copy files to the memory card. In some cases they must be converted by the Microsoft ActiveSync programme. Data Exchange via Card Reader You can transfer or synchronise data via ActiveSync. Particularly, this is the correct method if files to be transferred must be converted into a system your ...

• The display of your navigation system may show “light reflexions”. Please make sure of not being “blinded” during operation. • Do not mount the components within the airbag deployment zones. • Check the secure adherence of the suction cup at regular intervals. • The power plug will consume power, even if no device is connected. Remove it when not in use to avoid draining the battery. • Check all safety equipment in your car after installation. Additional Notes for Using the Navigation System on a Bike • Make sure during installation that the ability to steer is not impaired. Mounting the Navigation ...

navigation system from dust and dirt by using the storage pocket. The storage pocket, however, does not protect against rain or moisture. Make sure that the navigation system is not exposed to moisture. This may damage the electronic parts. When you use the navigation system, make sure that it is mounted in an upright position so that the GPS antenna (13) will receive a strong signal. If the signal is too weak, please adjust the direction of the GPS antenna to receive the best possible signal. INSTALLATION ...

Press it to switch on/off the unit. 2. Battery Charge Indicator When the battery is charging the indicator lights red When the battery is fully charged, the indicator turns green. 3. Back Button Press it to return to the previous menu. 4. Setting Button Press it to enter into the setting menu. 5. Navigation Pad Moves up/down/left/right by pushing the corresponding area of the pad. 6. Enter Button Press it to enter into the selected item. 7. Press it to enter into the main menu. 8. Touch Screen Displays the output of your device. Touch the screen with the stylus to select menu commands or enter information. 9. Bu ...

Pull the stylus pen out of its compartment in order to use it. Store it in this slot when not in use. The stylus pen is required for operating the touch screen. 12. Loudspeaker Plays back voice instructions and warnings. 13. GPS Antenna Receives the signals of the GPS satellites. 14. External Antenna Jack Interface for an optional second antenna. 11 12 13 14 ...

Separates the device completely from the battery (also hard reset). 20. Reset Button Press it to reset the unit. 15 20 RESET ON OFF BATTERY 19 18 17 16 16. SD/MMC Slot Accepts an optional SD (Secure Digital) Card for removable storage. 17. USB Interface Interface for connecting to a PC by means of the Sync- cable (for data synchronisation). 18. Headphone Jack Connects to a pair of stereo headphones (optional). 19. AC Adaptor Port Connection to external power supply. Left View Right View ...

determining your position. With the help of more than 24 satellites revolving around the earth, it is possible to determine your position on earth with an accuracy of a few meters. The satellite signals are received by the antenna of the integrated GPS receiver, which must have a “line of sight” to at least 4 satellites. • Note: By limited line of sight access (e.g. in tunnels, between houses, in woods or also in vehicles with metal- coated windows) it is impossible to determine the position. The satellite reception automatically picks up again as soon as the obstacle has been passed and the line of sight i ...

2.The navigation software starts automatically or after tapping the navigation control button, depending on the product version. 3.Tap the button to enter the destination and the address of your navigation destination. Then start the navigation by tapping Navigate. After a short time - if the satellite reception is adequate - you will receive the route information on the screen, augmented by voice instructions. For further operation of the navigation software, please refer to the comprehensive user handbook on the navigation CD. In addition, brief help is available to you on your navigation sys ...