Struers LaboPol-35 Instruction Manual
Read Online
Read the Struers LaboPol-35 Instruction Manual online using the built-in PDF viewer.
Key Pages of Document
Date of Release 27.09.2012 LaboPol-35 Instruction Manual Gebrauchsanweisung Mode d’emploi Spare Parts and Diagrams ...
Page User’s Guide ............................................................... 1 Reference Guide ......................................................... 8 Quick Reference Guide ............................................ 14 Spare Parts and Diagrams ....................................... 16 Always state Serial No and Voltage/frequency if you have technical questions or when ordering ...
To be read carefully before use 1. The operator(s) should be fully instructed in the use of the machine, any connected equipment and accessories and the applied consumables according to the relevant Instruction Manuals. 2. The machine must be placed on a safe and stable table with an adequate working height. All functions on the machine and any connected equipment must be in working order. 3. ...
contain electrical and electronic components and must not be disposed of as general waste. Please contact your local authorities for information on the correct method of disposal in accordance with national legislation. ...
Page 1. Getting Started Checking the Contents of Packing ..................................................... 2 Unpacking LaboPol-35 ....................................................................... 2 Placing LaboPol-35 ............................................................................ 2 Getting Acquainted with LaboPol-35 .................................................. 3 S ...
In the packing box you should find the following parts: 1 LaboPol-35 (Grinding/polishing machine) 1 Pressure hose 3/4" x 2 m 1 Filter gasket 1 Gasket ø11/ø24 x 1.5 mm 1 Reduction ring with gasket 1 Drain hose, ø38 mm x 3 m 1 Drain elbow pipe 2 Hose clamps 1 Protection ring Mains cable 1 Set of Instruction Manuals Detach LaboPol-35 from the bottom of the packing case by removing the four screws from ...
all the LaboPol components: Start switch Stop switch Speed control Turntable Water tap Water inlet Water outlet On/off switch for specimen mover Power supply socket for specimen mover Communication socket for specimen mover Fuse Main switch Power inlet Getting Acquainted with LaboPol-35 Rear View of LaboPo ...
equipment. LaboPol-35 is available in 2 voltage variants: 1/3 x 200-240 V / 50-60 Hz 1 x 100 V / 50-60 Hz The 1/3 x 200-240 V / 50-60 Hz LaboPol-35 is shipped with 2 types of Mains cables: The 2-pin (European Schuko) plug is for use on single-phase connections. If the plug supplied on this cable is not approved in your country, then the plug must be replaced ...
phase power connections. If the plug supplied on this cable is not approved in your country, then the plug must be replaced with an approved plug. The leads must be connected as follows: Green: earth Black: phase (live) White: neutral On the other end the cable is equipped with an IEC 320 cable connector that has to be connected to the LaboPol-35. Connecting a ...
machine and secure the hose using the hose clamp. Lead the other end of the outlet hose to the drain. Be absolutely sure to place the outlet hose with a steady slope to prevent the water from being discharged too slowly, which may cause overflow or blocking the water outlet. Avoid sharp bends on the outlet hose. Connect the inlet hose to the water tap ...
pins engage with the holes in the turntable. Set the speed control to the desired speed. Press the start switch . The machine starts operating. Press the stop switch . 3. Maintenance Clean all accessible surfaces with a moist cloth. Remove the splash ring and the grinding/polishing disc and remove all dirt from the ...
Page 1. Advanced Operations Selection of Disc ................................................................................ 9 Mounting of Specimen Mover (optional)............................................. 9 Mounting of LaboDoser (optional) ...................................................... 9 2. Struers Metalog Guide™ .................................................... 10 3. Acc ...
LaboPol-35 is designed for MD-Discs of 300 mm dia., wet grinding discs of 305 mm dia. and polishing discs of 300 mm dia. However, the whole range of Struers discs can be mounted. LaboPol-35 can be equipped with a LaboForce-Mi specimen mover. LaboPol-35, combined with a specimen mover, can be equipped with LaboDoser for automatic dosing of suspensions and lubricants. Selection of Disc Mounting of Specim ...
LaboPol-35 is designed for grinding, polishing and lapping. In Struers Metalog Guide™ you will find a detailed description of grinding/polishing for automated mechanical specimen preparation. Struers Metalog Guide™ offers preparation methods for the most common materials, based on a simple analysis of two key properties: hardness and ductility. Finding the right method, including choice of co ...
Specification Cat. No: Wet Grinding Discs 305 mm dia., aluminium 02426909 Polishing Discs 300 mm dia., aluminium 02426906 Discs for Magnetic Fixation MD-Disc, 300 mm dia. 02426918 Splash guard for LaboPol-35 for manual preparation 06116905 Specification Cat. No: LaboForce-Mi, 1/3 x 200-240 V / 50-60 Hz LaboForce-Mi, 1 x 100 V / 50-60 Hz Automatic specimen mover for the preparation of m ...
machine starts or the turntable will not turn The belt is too loose Call a Struers service technician. The belt must be tightened. The machine does not operate when the start switch is pressed. - The main switch is off - The fuse at the rear of LaboPol is blown - The switch for the specimen mover at the back of LaboPol is set to “on”, but no specimen mover is con ...
Subject Specifications Disc Diameter 300/305 mm 12" Rotational Speed 50 - 500 rpm Rotational direction Anti-clockwise Motor 370 W Torque at disc Continuous 7.1 Nm / 5.2 lbs-ft Max. 10.6 Nm / 7.8 lbs-ft Supply Voltage Power phases Single-phase versions: 1 (L + N + PE) Three-phase versions: 3 (3L + PE) Continuous load: Max. load: Power consumption 400 W 600 W Voltage / frequency 1/3 x 200-240 V / 50-60 Hz 1 ...
Place the disc on the turntable and turn it until the three driving pins engage with the holes in the turntable. Set the speed control to the desired speed. Press the start switch. Press the stop switch. Mounting a Disc Starting the Disc Stopping the Disc ...
Manufacturer, responsible for Technical File Struers A/S Pederstrupvej 84 DK-2750 Ballerup, Denmark Telephone +45 44 600 800 Herewith declares that Product Name: LaboPol-35 Type No: 611 Machine Type: Grinding and polishing machine is in conformity with the provisions of the following directives: Safety of Machinery 2006/42/EC according to the following standard(s): EN ISO 12100:2011, EN ISO 138 ...
