STOVES 602SCTC Operation & User’s Manual

Calls are charged at the basic rate, please check with your telephone service provider for exact charges Alternatively general, spares and service information is available from our website at: www.stoves.co.uk Glen Dimplex Home Appliances, Stoney Lane, Prescot, Merseyside, L35 2XW Warranty Registration 0800 952 1065 *Please call our Customer Care team for extended warranty Spares Store 0344 815 3745 Cu ...

Please read it carefully before you start using your appliance, as we have endeavored to answer as many questions as possible, and provide you with as much support as we can. General information, spares and service information is available from our website. If you should find something missing from your product or have any questions that are not covered in this use ...

appliance to avoid the possibility of electric shock and call for a service engineer’s visit. • During use the appliance becomes hot. Care should be taken to avoid touching heating elements. • Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced phy ...

you clean any part of it. • Although every care has been taken to ensure this appliance has no sharp edges. We recommend that you wear protective gloves when installing and moving this appliance. This will prevent injury. • This appliance must be fitted to a switch providing all pole disconnection with a minimum contact separation of 3mm. • Connection should be made with a suitab ...

Note: Your appliance layout may differ depending on the model. Control Panel Hob functions USING YOUR APPLIANCE Timer control Timer regulating controls Reset Control Power slider touch control Keylock control ON/OFF control Dual zone control Heating zone selection controls ...

• Read this guide, taking special note of the ‘Safety Warnings’ section. • Remove any protective film that may still be on your ceramic hob. Touch controls Use the flat of your finger, not the tip. The controls respond to touch, so you don’t need to apply any pressure. The touch control keys take approximately 1 second to respond to your touch. Always ensure the touch control area is clean, dry and free from any objects (e. ...

go out, to indicate that the ceramic hob is now in standby mode. 1. Touch the On/Off control key. All the indicators show “-” 2. Place a suitable pan on the cooking zone that you wish to use. • Make sure the bottom of the pan and the bottom of the cooking zone are clean and dry. 3. Touch the relevant heating zone selection cont ...

Turn the cooking zone off by touching the slider to . Make sure that the heating zone control display shows 0. Turn the whole cooktop off by touching the On/Off control key. ...

• The function only works in bottom left and top right cooking zones: • The dual cooking zone has two cooking areas that you can use a central section and an outer section. You can use the central section (A) independently or both sections (B) at once. 1. Touch the relevant heating zone selection key, and select a power level using the slider. 2. While the power level indicator is flashing, touch the dual zone control ke ...

• You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones on). • When the controls are locked, all the controls except the On/Off control are disabled. To lock 1. Touch the keylock control key. The timer display will show “LO“. To unlock 1. Touch the keylock control key until “LO” disappears from the timer display. When the keylock function is active, ...

Note: The minute minder does not switch any of the heating zones off automatically, and so any heating zones in use will continue to heat up until switched off manually. Setting�the�timer�to�turn�one�or�more�cooking�zones�off� automatically 1. First touch the heating zone selection control to select the relevant zone and use the power slider to select the required power level. Then t ...

To modify: 1. Select the relevant heating zone by touching the relevant zone selection control key. 2. While the current power level figure is flashing, touch the timer key. 3. The timer display shows the current time remaining flashing. 4. While the current time remaining figure is flashing, use the plus and/or minus keys to set the required cooking duration tim ...

change or cancel the cooking duration time. • When the timer is controlling more than one zone simultaneously, the timer display will always show the time remaining for the zone which is due to finish first. Note: In this example, the front-left zone (set to pow ...

excessively high temperature is observed, then the heating elements will be switched off automatically. Residual Heat Warning “H” will show which cooking zone is hot to touch. It will disappear when the surface has cooled down to a safe temperature. It can also be used as an energy saving function if you want to heat further pans, use the hotplate t ...

Dos Note: Always switch off your appliance and allow it to cool down before you clean any part of it. Note: Please take extra care when cleaning over the symbols on the control panel, as this can lead to them fading. H Tips: Some foods can mark or damage the metal or paint work e.g.; Vinegar, fruit juices and salt. Always clean food spillages as soon as possible. Don’ts IT IS IMPORTANT TO CLEAN YOUR APPLIANCE REGULARLY AS A BUI ...

Cut out the work surface according to the sizes shown in the drawing. For the purpose of installation and use, a minimum of 50mm space shall be preserved around the hole. Be sure the thickness of the work surface is at least 30mm. Please select heat-resistant and insulated work surface material (Wood and similar fibrous or hygroscopic material shall not be used as work surface material unless sealed) to avoid t ...

Make sure the ceramic hob is well ventilated and that air inlet and outlet are not blocked. In order to prevent accidental touch of the hot base of the appliance or the risk of electric shock, insert a wooden isolation plate at least 50mm beneath the base of the hob, unless an oven is installed directly below the hob. WARNING: There are ventilation holes around outside of the hob. YOU MUST ensure these holes are no ...

Ensure that there is a small gap between the installation brackets and the underside of the worktop to allow space for heat expansion - see the above. ...

WARNING: This appliance must be earthed. 1. If the cable is damaged or needs replacing, this should be done by an after-sales technician using the proper tools, so as to avoid any accidents. 2. If the appliance is being connected directly to the mains supply, an omnipolar circuit breaker must be installed with a minimum gap of 3mm between the contacts. 3. The installer must ensure that the correct electrical ...