Stockmaster Step-Thru Assembly Instructions Manual

Platform - Safety Rail Assembly IMPORTANT: To avoid assembly problems follow these instructions exactly. Step 1 - Fasten the two piece Side Safety Rail Set together at A using an M6 x 40mm Bolt and Nyloc Nut. Repeat for the second rail. (See illustration No. 1) Step 2 - Attach one Side Safety Rail to the Rear Brace Plate with two M6 x 40mm Bolts and Nyloc Nuts at B and C. Position the Rear Brace Plate so that it wraps around the Safety Rail. (See illustration No. 2) Step 3 - Position the Platform and Side Safety Rail as shown and slide the front of the Side Safety Rail into the Platform Kickrail housing at position D. ...

Ladder Frame Assembly IMPORTANT: To avoid assembly problems follow these instructions exactly. Work Safely - Do not stand the frames upright when assembling. Place the frames in the positions as shown in the illustrations. Step 1 - Lay the Rear Frame (without steps) on the floor and place the Platform over the frame as shown. Check that the side with the Angled Brace “E” is face side down. (See illustration No. 1) Step 2 - Fix the Tube Brace, Platform and Rear Frame together using a 10 x 20mm bolt and nut - finger tight only. For ease, lift the Frame up slightly. Repeat the process and fit the remaining Tube Brace. (See illus ...

Tube Brace Assembly IMPORTANT: To avoid assembly problems follow these instructions exactly. Work Safely - Do not stand the frames upright when assembling. Place the frames in the positions as shown in the illustrations. Instructions for sizes with 3 to 7 steps including the platform: There are no Tube Braces to be fitted to these sizes. Proceed to Control Handle Assembly Instructions for sizes with 8 to 10 steps including the platform: See Steps 1 & 2 only Step 1 - Place the Platform on its side and place something under the Platform as illustrated so the centre line of the Rear Frame is approximately parrallel to the floor. The M ...

Control Handle Assembly IMPORTANT: To avoid assembly problems follow these instructions exactly. Work Safely - This assembly is done with the Stockmaster standing upright. Step 1 - Position the Control Handle in the Step Frame between the 2nd and 3rd steps. (See illustration No. 1) Step 2 - Fix the Control Handle to the Frame. Pass an “E” Pin through the hole in the Control Handle and the Upper hole in the Mounting Angle of the Step Frame. (See illustration No. 2) Step 3 - Secure with an “E” Clip fitted to the outside ring of the “E” Pin. (See illustration No. 3) Illustration 1 Illustration 2 Illustration 3 “E” C ...

Work Safely - This assembly is done with the Stockmaster standing upright. Step 1 - Fix the Handrail to the Platform Kickrail. Slide the Handrail into the Kickrail and rotate the handrail so that the lower end is over the Step. Place an M6 x 40 bolt through the bottom hole at the front of the Kickrail and fit a nut Finger tight only. (See illustration No. 1) Step 2 - Fix the Handrail to the Step. Place an M6 x 40 bolt through the Handrail and fit the nut under the Step. Check that the Handrails are correctly aligned and tighten all four bolts using the Hex Key and Double Ended Sp ...

Work Safely - Do not stand the frames upright when assembling. Place frames in the positions shown in the illustrations Step 1 - Fix the Mobilisation Rails (Rectangular Hollow Section - RHS) to the Frames at A & B. The fixing detail is shown in steps 2 to 3 (See illustration No. 1) Step 2 - Fix the Mobilisation Rails to the Rear Frame at A. Use a 12 x 65mm Bolt, Nylon Sleeve, Large Nylon Spacer and Nyloc Nut. Pass the Bolt thru the Frame and fit the Large Nylon Spacer and Nylon Sleeve. (See illustration No. 2) Step 3 - Fit the Mobilisati ...

Before use - See the product Risk Assesment at www.stockmaster.co WARRANTY Thank you for choosing Stockmaster your safety is in good hands Register your 2 year warranty online at www.stockmaster.co ...