Stockmaster Tracker Assembly Instructions Manual

Platform - Safety Rail Assembly IMPORTANT: To avoid assembly problems follow these instructions exactly. Note: If assembling the platform with Folding Safety Rails first read the seperate instructions included with the Folding Safety Rail Bracket Kit. Step 1 - Fix the Rear Safety Rail to the rear of the Platform Kickrail. Use the M6 x 45mm Patchlok bolts (blue coated) and screw in with the hexagon key leaving the bolt slight ...

Platform - Safety Rail Assembly Illustration 5 Illustration 6 M6 x 65 NEXT: For Standard Models - Proceed to Ladder Frame Assembly NEXT: For PRO Models - Proceed to Rota-Gate Assembly ...

B A E M6 x 40 M6 x 40 C D C D E IMPORTANT: To avoid assembly problems follow these instructions exactly. Step 1 - Fasten the Angle Rotating Bracket to the Lower Side Safety Rail at A and B using two M6 x 40mm Bolts and Nyloc Nuts - Finger tight only. (See illustration No. 1) Step 2 - Attach the Nylon Catch Plate to the inside of the Rear Safety Rail wi ...

Auto-Safe Gate Assembly Illustration 1 Illustration 2 Illustration 3 Illustration 4 A M6 x 70 A M6 x “U” Bolt M6 x “U” Bolt IMPORTANT: To avoid assembly problems follow these instructions exactly. Work Safely - Do not stand the frames upright when assembling. Step 1 - Remove the M6 x 65mm screw and nyloc nut at A from the LHS Upper Side Safety Rail as viewed from the entry point of the platform and discard. (See illustration ...

Ladder Frame Assembly IMPORTANT: To avoid assembly problems follow these instructions exactly. Work Safely - Do not stand the frames upright when assembling. Place the frames in the positions as shown in the illustrations. Note: If assembling the platform with Folding Safety Rails first read the seperate instructions included with the Folding Safety Rail Bracket Kit. Step 1 - Lay the Rear Frame (without steps) on the floor. Check that ...

Ladder Frame Assembly Illustration 5 Illustration 6 M10 x 20 M10 x 20 NEXT: Proceed to Tube Brace Assembly. ...

Tube Brace Assembly IMPORTANT: To avoid assembly problems follow these instructions exactly. Work Safely - Do not stand the frames upright when assembling. Place the frames in the positions as shown in the illustrations. Instructions for sizes with 4 to 7 steps including the platform: There are no Tube Braces to be fitted to these sizes. Proceed to Control Handle Assembly Instructions for sizes with 8 to 11 steps including the platform: ...

Control Handle Assembly IMPORTANT: To avoid assembly problems follow these instructions exactly. Work Safely - This assembly is done with the Stockmaster standing upright. Step 1 - Position the Control Handle in the Step Frame between the 2nd and 3rd steps. (See illustration No. 1) Step 2 - Fix the Control Handle to the Frame. Pass an “E” Pin through the hole in the Control Handle and the Upper hole in the Mounting Angle of the ...

Work Safely - This assembly is done with the Stockmaster standing upright. Step 1 - Fix the Handrail to the Platform Kickrail. Slide the Handrail into the Kickrail and rotate the handrail so that the lower end is over the Step. Place an M6 x 40 bolt through the bottom hole at the front of the Kickrail and fit a nut Finger tight only. (See illustration No. 1) Step 2 - Fix the Handrail ...

Work Safely - This assembly is done with the Stockmaster standing upright. Step 1 - Fix the Mobilisation Rails (Rectangular Hollow Section - RHS) to the Frames at A & B (See illustration No. 1) Step 2 - Using the M8 x 40 bolts, nuts and sleeves. Pass the bolt through the hole in the Frame Bracket at C, on the Front Frame. Place a sleeve over ...

Before use - See the product Risk Assesment at www.stockmaster.co WARRANTY Thank you for choosing Stockmaster your safety is in good hands Register your 2 year warranty online at www.stockmaster.co ...