Steelcase Secant Assembly Instructions Manual

939504557 Rev T Secant® Freestanding Worksurface Support ® If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500) Or visit our website: www.steelcase.com © 2000 Steelcase Inc. Grand Rapids, MI 49501 U.S.A. Printed in U.S.A. ACR l ll l ACR II #3 Bit #3 Square Drive Bit Use care during the staging and installation to � prevent damage to finished surfaces. ...

939504557 Rev T 1. For an end-of-run application,� attach each bracket to support� with two (2) screws in opposing� holes.� 1a. NOTE: Change glides to� opposite end to change from one� hand to the other on end panel.� � � � � � � � 2. For a shared application, attach� each bracket to support with� two (2) screws using in-line holes. Corner Support Intermediate Support End Panel Support 1a Front worksurface screw location. C-Leg Support ...

939504557 Rev T 3. Attach one end of the stretcher to� one completed support assembly� with four (4) screws, then attach� opposite end of stretcher to adjacent� support assembly.� � 3a. When the intermediate support is� used in the center position of a single� worksurface, bend the tabs of the� intermediate support bracket so that� they are flush with Surface A. Surface A ...

939504557 Rev T 4. �Attach appropriate plates to �intermediate and c-leg supports �with two (2) screws. ...

939504557 Rev T 5.� Align worksurface to support structure �fitting over projections and attach, �using screws as shown. NOTE: Adjust support side to side position to minimize worksurface mismatch. ...

939504557 Rev T 6. Peel backing off double-sided tape� to expose sticky surface, then press wire� manager onto back side �of support. This� is typical for all supports. C-Leg Support Wire Manager ...

939504557 Rev T Conference Link and Conference Wing Assembly� � 1. � For an end-of-run application, attach �each bracket to support with �two (2) screws in opposing holes.� � 2. �For a shared application, attach �each bracket to support with �two (2) screws using in-line holes. Corner Support Intermediate Support ...

939504557 Rev T Conference Link and Conference Wing Assembly� � 3. Attach one end of the stretcher to one� completed support assembly with� four (4) screws, then attach opposite end� of stretcher to adjacent support assembly. 4. Attach post to conference link or� conference wing using (4) screws. Conference wing Conference link NOTE: Adjust support side to side position to minimize work surface mismatch. ...

939504557 Rev T Conference Link and Conference Wing Assembly� � 5. �Attach mounting plate to support. 6. � Attach top with post to brackets. 7. �Attach wire manager as shown in step 6 on page 6. NOTE: Adjust support side to side position to minimize work surface mismatch. ...

939504557 Rev T End Cap Assembly � 1. � For end cap installation, attach each bracket �to support with two (2) screws using in-line holes.� � 2.� Attach stretcher to support assembly with �four (4) screws.� 3. � Install the mounting plate to support using �three (3) 1/4-20 flat head cross-recessed �machine screws. C-Leg Support ...

939504557 Rev T 4. � Attach end cap and adjoining worksurface to �mounting plate using three (3) #12 x 1" long �flat head wood screws in each surface.� � � � 5. � Attach worksurface straps at front and rear� of worksurface using one (1) #8 x 7/8" long� flat head wood screw in each surface. Worksurface attachment holes Install these (2) screws after front edges of worksurfaces are aligned. ...

939504557 Rev T C-Leg Support Corner Support Intermediate Support 1. 2. 3. Secant® Adjustable Height� Worksurface Support� 1. For maintenance adjustable C-Leg� � supports only!� � � a) Install glide assembly.� � � b) Snap plastic cover over glide assembly.� 2. For end-of-run applications, attach each� � bracket to support with four (4) screws.� 3. For shared applications, attach each� � bracket to support with two (2) screws. a b ...

939504557 Rev T 4. � Attach one end of stretcher to one �completed support assembly with �four (4) screws, then attach opposite �end of stretcher to adjacent support �assembly. Continue until the entire �support structure is complete. The nominal length of the Corner Stretcher is 6" shorter than the nominal length of the Corner Worksurface. ...

939504557 Rev T 5.� Attach mounting plate to supports with �three (3) 1/4-20 flat head cross-recessed� machine �screws. ...

939504557 Rev T 6. � Attach mounting plate to supports with �three (3) 1/4-20 flat head cross-recessed machine �screws. �Use (4) screws on the mounting plate for C-Leg �end support. Install these (2) screws after front edge of worksurfaces are aligned. ...

939504557 Rev T 7. Peel backing off double-sided tape� to expose sticky surface, then press wire� manager onto back side �of support. This� is typical for all supports. C-Leg Support Wire Manager 1. 2. ...

939504557 Rev T Conference Link and Conference Wing Assembly� 1. For each end-of run application attach �each bracket to support with four (4) screws. 2.� For a shared application, attach each �bracket to support with two (2) screws. C-Leg Support Intermediate Support ...

939504557 Rev T Conference Link and Conference Wing Assembly � 3.� Attach one end of the stretcher to one �completed support assembly with four (4) �screws, then attach opposite end of stretcher to �adjacent support assembly.� 4. � Attach post to conference link or conference �wing using (4) screws. Conference wing Conference link 3. ...

939504557 Rev T Conference Link and Conference Wing Assembly � 5. � Attach mounting plate to support. 6. � Attach top with post to brackets. 7. � Attach wire manager as shown� in step 6 on page 6. ...

939504557 Rev T Spanner worksurface� 5. � Connect supports with brackets. �Attach mounting plates to supports.� 6.� Align spanner worksurface to mounting �plates and attach using three (3) #12 x 1" �long flat head screws as shown. ...