Staubli MA251 Operating Instructions Manual

PV-CZM... * UL file E343181 MA251 (中 -英） 操作指导 MA251 (cn_en) Operating instructions 压接钳 PV-CZM 适用于MC3和MC4 和MC4-EVO 2 Crimping pliers PV-CZM... for MC3, MC4 and MC4-EVO 2 目录 安全说明 ������������������������������������������������������������������������������������2 工具说明 MC3............................................................................3 工具说明 MC4...................................................................... ...

安全说明 Safety Instructions 该产品应由具有相应资质或经过培训的人员，遵守相关安全应 用规范进行安装。 Stäubli不承担由于不遵守这些警告而产生的任何责任。 The products may be assembled and installed exclusively by suitably qualified and trained specialists duly observing all ap- plicable safety regulations. Stäubli Electrical Connectors (Stäubli) does not accept any li- ability in the event of failure to observe these warnings. 仅可使用Stäubli指定的零件和工具。对于自行装配，请务必按 照本文指出的准备及安装程序，否则Stäubli不能保证产品的安 ...

1 2 3 4 5 4 工具说明-MC3 Explanation for MC3 (ill. 1) 压接钳 PV-CZM-16100A 包括：两个可更换的定位块和两个可更 换的嵌块。 (ill. 1) Crimping pliers PV-CZM-16100A incl. two interchangeable Locators and two interchangeable crimping inserts 压接范围: 2,5 / 4 / 6 mm2 (14 / 12 / 10 AWG) 订货号: 32.6020-16100A Crimping range: 2,5 / 4 / 6 mm2 (14 / 12 / 10 AWG) Order No.: 32.6020-16100A 单独部件 Individual parts (ill. 2 + 3) 可更换的嵌块 (ill. 2 + 3) Interchangeable crimping inserts 压接范围 Crimping range 型号 Type 订货号 Order No. mm2 AWG 2,5 / 4 / 6 14 / 12 / 10 PV-ES-CZM-16100 32.6021-16100 ...

5 1 2 3 5 4 6 8 7 6 7 8 工具说明-MC4 Explanation for MC4 (ill. 5) 压接钳包括定位块PV-LOC和嵌块 (ill. 5) Crimping pliers incl. locator PV-LOC and built-in crimping insert 压接范围: 1,5 / 2,5 / 4 mm2 (14 / 12 AWG) 型号: PV-CZM-18100 订货号: 32.6020-18100 Crimping range: 1,5 / 2,5 / 4 mm2 (14 / 12 AWG) Type: PV-CZM-18100 Order No.: 32.6020-18100 压接范围: 2,5 / 4 / 6 mm2 (12 / 10 AWG) 型号: PV-CZM-19100 订货号: 32.6020-19100 Crimping range: 2,5 / 4 / 6 mm2 (12 / 10 AWG) Type: PV-CZM-19100 Order No.: 32.6020-19100 压接范围: 4 / 10 mm2 型号: PV-CZM-20100 订货号: 32.6020-20100 Crimping range: 4 / 10  ...

9 10 9 11 11 12 13 10 12 压接范围 Crimping range 型号 Type 订货号 Order No. mm2 6 / 10 PV-ES-CZM-21100 32.6021-21100 压接范围 Crimping range 型号 Type 订货号 Order No. AWG 8 / 12 / 10 PV-CZM-22100 32.6020.22100 (ill. 11) 定位块 PV-LOC 订货号: 32.6040 定位块 PV-LOC-B 订货号: 32.6055 注意: 当使用压接工具PV-CZM-22100 时，请使用定位块PV-LOC-B。 (ill. 11) Locator PV-LOC Order No.: 32.6040 Locator PV-LOC-B Order No.: 32.6055 Note: When using the crimping tool PV-CZM-22100, please use the locator PV-LOC-B� 工具说明-MC4-EVO 2 Explanation for MC4-EVO 2 (ill. 12) 压接钳包括定位块和嵌块 (ill. ...

13 14 15 16 2 1 3 5 4 6 7 8 单独部件 Individual parts (ill. 13 + 14 + 15) 可更换的嵌块 (ill. 13 + 14 + 15) Interchangeable crimping inserts 压接范围 Crimping range 型号 Type 订货号 Order No. mm2 AWG 1,5 / 2,5 / 4 14 / 12 PV-ES-CZM-40100 32.6021-40100 压接范围 Crimping range 型号 Type 订货号 Order No. mm2 AWG 2,5 / 4 / 6 14 / 12 / 10 PV-ES-CZM-41100 32.6021-41100 压接范围 Crimping range 型号 Type 订货号 Order No. mm2 AWG 4 / 10 12 / 8 PV-ES-CZM-42100 32.6021-42100 (ill. 16) 定位块 PV-LOC-C 订货号: 32.6056 (ill. 16) Locator PV-LOC-C Order no.: 32.6056 Pos. 电缆截面积 Cable cross section 适用零件 ...

21 22 19 20 17 18 嵌块安装 Fitting the crimping insert (ill. 21) 打开压接钳（把钳子压到底后可松开） ，把上下两个嵌块装上。嵌块上的印字 必须和压接钳的印字在同一侧。闭合压 接钳，拧上螺栓以固定嵌块。 (ill. 21) Open the crimping tool (press com- pletely together and release). Insert both crimping inserts. The markings must be on the same side as the marking on the crimping tool. Close crimping tool and screw both crimping inserts tight. (ill. 22) 把定位块装到导杆上 (ill. 22) Insert locator into the guide pin. 更换嵌块 Exchanging the crimping inserts 嵌块拆除 Removin ...

25 26 23 24 (ill. 23) 转动定位块（会被磁铁吸住） (ill. 23) Rotate the locator (held magnetically) (ill. 24) 卡住定位块 (ill. 24) Lock the locator. 压接 Crimping 举例 ADBP3/... + ADSP3/... Example for ADBP3/... and ADSP3/... (ill. 25) 拆掉定位块，放入已剥皮的电缆，直到 绝缘层碰到嵌块。放入连接器金属端子 并将钳子压到底。 检查压接效果（见ill.23) (ill. 25) Remove the locator. Insert the stripped cable on the left side until the insulation comes into contact with the crimping insert. Close crimping tool completely. Check crimp (see ill. 23). 举例 KBT4.../KST4... Example for KB ...

29 27 28 (ill. 27) 慢慢闭合压接钳，直到金属端子固定 住。 (ill. 27) Lightly press the pliers together so that the crimping tabs lie securely within the crimping die. (ill. 28) 插入已剥皮的电缆，直到绝缘层碰到嵌 块，然后把钳子压到底。 (ill. 28) Insert the stripped cable until the insulation comes into contact with the crimping insert. Close crimping tool completely. 压接质量 Crimping quality 通过压接高度可以评估压接质量。对于 电缆FLEX-SOL-XL—和Studer—BETAflam®, 常见高度值如下表。 The quality of the crimp can be as- sessed on the basis of the crimp height. Typical v ...

制造商/Producer: Stäubli Electrical Connectors AG Stockbrunnenrain 8 4123 All schwil/Switzerland Tel. +41 61 306 55 55 Fax +41 61 306 55 56 mail [email protected] www.staubli.com/electrical © by Stäubli Electrical Connectors AG, Switzerland – MA251 – 01.2017, Index a, Marketing Communications – 保留修改权利 / Subject to alterations Notes: ...