Stark 5030 Operating And Maintenance Manual

General Congratulations on the purchase of your STARK Road Grader! For us, the long lifecycle and efficiency of your new equipment is a priority. To keep the road grader in top working condition, read this manual carefully before using the equipment. STARK products are engineered and manufactured in Finland, and each of them is equipped according to the needs of the customer. Never let anyone operate or maintain the device without reading this ...

Table of contents General ................................................................................................................................................. 2 Read before use ................................................................................................................................... 2 1. DECLARATION OF CONFORMITY ............................................................................................... ...

1. DECLARATION OF CONFORMITY The original manufacturer’s EC declaration of conformity: Generic product name: Road grader Models: TL 7500 Manufacturer: Lametal Ltd Kaskenviertäjäntie 2 73100 LAPINLAHTI, Finland tel. +358 17 731 565 Declares that the above-mentioned equipment meets the provisions of Directive 2006/42/EC on machinery and, where applicable, comply with the standards • SFS-EN ISO 12100-1, • SFS-EN ISO 12100-2 • SFS-EN 1050 ...

2. PURPOSE OF USE STARK Road graders are used for grading gravel roads and flat areas and for transferring ice (removal of packed snow). The device can also be used to shape and align fields. 3. SAFETY PRECAUTIONS Make sure you know your equipment before you start using it. Equipment may be operated only by an individual who is thoroughly familiar with its use. Before connecting hydraulics to the base machine, make sure that: - there is no-one ...

4. IDENTIFICATION INFORMATION AND SPAREPARTS 4.1. Identification plate Identification plate is placed on the side of the equipment. The plate includes contact information, machine type, year of manufacture, serial number and weight. (See an example of an identification plate in picture 1 below). The first four numbers in the serial number indicate the month and year of manufacture (month first). The remaining five numbers constitute the machine ...

5. MAIN PARTS OF THE ROAD GRADER Picture 2. Main parts of the road grader 1) Frame of the road grader 2) Shaft of the windrow spreader 3) Front wing 4) Middle wing 5) Back wing 6) Windrow spreader 7) Lift arm 8) Box ...

6. ATTACHING THE ROAD GRADER When attaching the road grader for the first time, make sure it is compatible with the base machine by following the instructions below. Always check the compatibility when attaching the road grader to a new base machine. Make sure that the base machine allows installation of the road grader. Minimum requirements of the base machine: - Minimum weight of 6,000 kg - With wireless controller, 1 x 2-way hydraulic valve ...

7. OPERATING THE ROAD GRADER Before operating the road grader, make sure: - the road grader is installed correctly - all locking pins are in place - hydraulic hoses are connected right and properly - hoses are intact - there are no oil leaks - all functions are working properly - learn to operate the road grader in a closed area before actually using the device 7.1. Operating instructions 1. Make sure that the attachment and the base machine ar ...

7.3. Adjusting the blades Edge of the blade should be 15–45 mm lower than the blade frame. Blades need to be adjusted at the latest when the blade edge is less than 10 mm lower than the blade frame (picture 4). Do not adjust the blades more than 50 mm lower than the blade frame. Picture 4. Minimum distance of the blade to the frame Blades can be adjusted three times. Each time there will be about 45 mm wear edge on the blade. First when the ...

Picture 7. Turned blade Picture 8. Turned and lowered blade 7.4. Detaching the road grader - When you disconnect the blade assembly from the tractor, lower the assembly on a flat surface and rest it on the blades. - Rest the blades on top of strong support brackets. - When transferring road grader for long distances, windrow spreader must be secured to upwards stance with e. g. a cargo strap. - Turn off the base machine and remove pressure fro ...

8. MAINTAINING THE ROAD GRADER 8.1. General safety precautions for the use and maintenance - Comply with the applicable laws and regulations and the instructions in this manual - Never go under the road grader if it is not supported - Always put on the base machine’s parking brake before any servicing on the road grader. - Use only tools which are in good condition. - Watch out for pressurized hydraulic hoses and components. - Make sure ther ...

8.4. Daily maintenance It is important to perform a daily visual inspection of the road grader for early detection of possible faults and to prevent further damage. Inspect the following items on the road grader daily: - Hydraulic hoses and components for possible leaks - General mechanical condition 8.5. Maintenance after every 10 hours - Lubricate marked components (see a later section for instructions) - Check the bolts for tightness (table ...

8.7. Lubrication points 1) Pegs of the lift arm 2) Hydraulic cylinder of the windrow spreader’s shaft 3) Hydraulic cylinder of the wheel rack 4) Pegs of the wheel rack 5) Wheel’s brake pole 6) Fastener peg of the windrow spreader 7) Hydraulic cylinder of the windrow spreader’s support wheel 8) Pole of the extension blade 9) Fastener peg of the windrow spreader Picture 9. Lubrication points Picture 10. Lubrication points ...

9. HYDRAULICS The road grader is attached to the base machine with 10-hose hydraulics (figure 1). The system has been tested and adjusted by the manufacturer. Any alterations or modifications to the hydraulic system are on the sole responsibility of the client. 9.1. 10-hose hydraulics 1. Cover plate 2. Side blade 3. Main blade 4. Windrow 5. Frame rack 1 6. Free rotation 7. Frame rack 2 8. Windrow extension 9. Windrow rack 1 10. Windrow rack 2 ...

10. WARRANTY POLICY 1. Warranty coverage Lametal Oy, the manufacturer of STARK attachments, offers new devices a guarantee which covers material and manufacturing defects in accordance with the terms in this warranty policy. Limitations to the warranty are specified in point 7. 2. Warranty starting date The warranty starts on the agreed date of product delivery to the client, or on the date of approved instalment or on the date the equipment h ...