ST UC2842B Manual 

Text of ST UC2842B Manual 

HIGH PERFORMANCE CURRENT MODE PWM CONTROLLER

. TRIMMED OSCILLATOR FOR PRECISE FRE- QUENCY CONTROL . OSCILLATOR FREQUENCY GUARANTEED AT 250kHz . CURRENT MODE OPERATION TO 500kHz . AUTOMATIC FEED FORWARD COMPENSA- TION . LATCHING PWM FOR CYCLE-BY-CYCLE CURRENT LIMITING . INTERNALLY TRIMMED REFERENCE WITH UNDERVOLTAGE LOCKOUT . HIGH CURRENT TOTEM POLE OUTPUT . UNDERVOLTAGE LOCKOUT WITH HYSTER- ESIS . LOW START-UP

All voltages are with respect to pin 5, all currents are positive into the specified terminal.

PIN CONNECTION (top view) COMP VFB ISENSE RT/CT GROUND OUTPUT Vi VREF 1 3 2 4 6 5 7 8 D95IN332 Minidip/SO8 ORDERING NUMBERS SO8 Minidip UC2842BD1; UC3842BD1 UC2843BD1; UC3843BD1 UC2844BD1; UC3844BD1 UC2845BD1; UC3845BD1 UC2842BN; UC3842BN UC2843BN; UC3843BN UC2844BN; UC3844BN UC2845BN; UC3845BN ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit Vi Supply Volt

ELECTRICAL CHARACTERISTICS ( [note 1] Unless otherwise stated, these specifications apply for

-25 < Tamb < 85°C for UC284XB; 0 < Tamb < 70°C for UC384XB; Vi = 15V (note 5); RT = 10K; CT = 3.3nF) Symbol Parameter Test Conditions UC284XB UC384XB Unit Min. Typ. Max. Min. Typ. Max. REFERENCE SECTION VREF Output Voltage Tj = 25°C Io = 1mA 4.95 5.00 5.05 4.90 5.00 5.10 V ∆VREF Line Regulation 12V ≤ Vi ≤ 25V 2 20 2 20 mV ∆VREF Load Regulation 1 ≤ I

1. Max package power dissipation limits must be respected; low duty cycle pulse techniques are used during test maintain Tj as

close to Tamb as possible. 2. These parameters, although guaranteed, are not 100% tested in production. 3. Parameter measured at trip point of latch with VPIN2 = 0. 4. Gain defined as : ∆ VPIN1 A = ; 0 ≤ VPIN3 ≤ 0.8 V ∆ VPIN3 5. Adjust Vi above the start threshold before setting at 15 V. ELECTRICAL CHARACTERISTICS (

Figure 1: Open Loop Test Circuit.

RT A 2N2222 4.7KΩ 1KΩ ERROR AMP. ADJUST 4.7KΩ 5KΩ ISENSE ADJUST 100KΩ COMP VFB ISENSE RT/CT 1 2 3 4 CT 7 6 5 8 VREF Vi OUTPUT GROUND 0.1µF 0.1µF VREF Vi OUTPUT GROUND 1W 1KΩ D95IN343 High peak currents associated with capacitive loads necessitate careful grounding techniques. Timing and bypass capacitors should be connected close to pin 5 in a single point ground. The transistor and 5 KΩ potentiometer are u

Figure 4: Oscillator Discharge Current vs. Tem-

perature. 1 2 3 5 40 50 60 70 80 90 Dmax (%) 0.8 RT(KΩ) D95IN336 Vi=15V CT=3.3nF TA=25˚C Idischg=7.5mA Idischg=8.8mA Figure 5: Maximum Output Duty Cycle vs. Tim- ing Resistor. 10 100 1K 10K 100K 1M f(Hz) -20 0 20 40 60 80 (dB) 180 150 120 90 60 30 φ D95IN337 Vi=15V VO=2V to 4V RL=100K TA=25˚C Gain Phase Figure 6: Error Am

ST Microcontrollers Owners Instructions: