Sphere Mata 1 Product Manual

to change designs and specifcations for improving the products without prior notice. www.coastrv.com.au Product Manual Mata 1 & Mata 1E Tire Pressure Monitoring System ...

Before using the product, please read and follow the manual instructions carefully. Welcome For your Safety 01 02 02 03 05 05 06 06 06 07 07 08 09 12 14 15 16 17 19 06 11 12 Package Contents Display TPMS Settings Changing Sensor Batteries Installation Sensor Pairing Product Specifcations Q&A A brief look TPMS warning signals Charging the display Display ON/OFF Settings mode Functions rotation Pressure unit selection Temperature unit sele ...

trailer view every 5 seconds. Spare tire pressure can be checked by pressing twice. Quick check: press to switch from 4-wheel view trailer view spare tire view. 4-Wheel View Battery status Warning indicator Solar power charging Tire temperature Trailer View No solar power Spare Tire View Spare tire 2 Spare t ...

When the unit detects abnormal tire conditions or low sensor battery, it will emit audio beeps and visual warning. Press any button to temporarily silence the alarm. High pressure alarm Low pressure alarm High temperature alarm Sensor failure signal Low sensor battery Spare tire alarm* (e.g. low pressure) Spare tire alarm will alert for high/low pressure. Spare tire alarm will beep 15 times and fall silent. ...

2) Then short press button to rotate through the functions. 3) To exit Settings Mode, hold button for 3 seconds. NOTE: All changes to the settings are autosaved. TPMS Settings 05 06 Settings Mode Functions Rotation Pressure Unit Selection Pressure Unit Selection Temperature Unit Selection High/Low Pressure Alarm High Temperature Alarm Tire Swap 1. Enter Settings Mode. 2. P ...

High and Low Pressure Alarm 07 08 Users are able to customise 4 sets of pressure alarms, including: Front wheels set, rear wheels set, trailer front wheels set, and trailer rear wheels set. 1. Enter Settings Mode and rotate to High Pressure Alarm settings [HI] for the frst set. 2. Press or to choose the desired high pressure alarm threshold. 3. Move onto Low Pressure Alarm settings [LO] for the frst set of wheel ...

rear right wheel of the vehicle. ENSURE that these instructions are followed carefully: Tire Swap Function 09 10 1) Original Tire Pressure. 2) Enter Settings Mode, rotate to Tire Swap. 4) Press once. 5) Press button twice to select the second wheel (e.g. front right wheel) for Tire Swap. C2 and the selected wheel will fash. 6) Press once. Tire Swap is done ...

battery is low, please replace the CR1632 button cell battery by following the instructions below: i. Unscrew the valve cap ii. Thread the theftproof nut through iii. Screw on the sensor iv. Tighten the nut using the spanner 11 12 i. Unscrew the sensor cover iii. Replace with new CR1632 battery ii. Remove the old battery (the + side faces upwards) iv. Screw on the sensor co ...

DO NOT mount the display on top of the airbag compartment. Some products such as DVRs may cause interference. The display should be mounted away from such products. ii. Place the display on the dashboard in the right place. i. Mount the display on the dashboard by double-sided sticker. 13 14 Sensor Installation – INTERNAL SENSOR 2. Display Installation i. Remove the original tire valve ii. Install ...

Sensor Pairing Mode. iii. External sensors: screw on the new sensor to the corresponding tire until data shows up on the display with a ‘beep’ sound. Internal sensors: With sensors installed, infate or defate the corresponding tire until data shows up on the display with a ‘beep’. ii. Press or button to select the desired tire position. iv. Short press button once to save t ...

tire position, and repeat steps iii)~iv) to pair the other sensors. vi. If you have fnished pairing selected sensors, hold button for 3 seconds to exit Sensor Programming Mode. 17 18 Product Specifcations Display Factory Default Settings Operating frequency Operating temperature 433.92MHz ±50KHz -20～+70℃ / -4～158˚F User selectable range for alarms High Pressure Low Pressure High temperature 0.8 ...

After installation, why does air leakage occur? Tire valves may not be of universal standard. Check with your installer. There are two methods: 1. External sensors can be taken off and screwed onto the correct position; or 2. Users can utilize the Tire Swap function to exchange two tire positions each time, until all tires are swapped to the correct position. Do I need to perform a dynamic wheel balancing? After installing internal sensors, ...