Southwire 10020N Operating Instructions Manual

10020N manual Contents Made in China Product distributed by Southwire Company, LLC One Southwire Drive, Carrollton, GA 30119 ©2014 Southwire Company, LLC. All rights reserved. southwiretools.com 1-855-SW-T00LS Toll Free Technical Help Línea de Ayuda Técnica Gratuita Scan for warranty information and to access our mobile site. Escanea para información de garantía y acceso a nuestro sitio móvil. Operating Instructions 10020N 3in1 MULTIMETER Hz% MODE ® TESTING EQUIPMENT E361819 Instrucciones de Operación MULTÍMETRO 10020N 3en 1

resistance, frequency, and duty cycle. Other functions include non-contact AC voltage detection, continuity and diode test. �������������������������������������������������� This meter is fully tested and calibrated and, with proper use, will provide many years of reliable service. ���������������������������������������������������������������� Instructions in this manual before using this meter. ��������������������������������������������������������������� ���������������������������������������������������������� ����������������������������������������������������������� measurements. ������������������������������������������������������������� always disconnect the test leads from the circuit under test. ����������������������������������������������������� ��������������������������������������������������������� ������������������������������������������������������������� ���������������������������������������������������������� ���������������������������������������������� �����������������������������������������������������damaged. ��������������������������������������������������������������� electrical storms. ����������������������������������������������������������� �������������������������������������������������� Protection may be compromised. ������������������������������������������������������������ ��������������������������� 2 Input Limits Function Maximum Input Voltage AC, Voltage DC Frequency, Duty Cycle Amperage µA, mA AC/DC Resistance, Diode & Continuity Test 600V AC/DC 600V AC/DC Maximum Amperage 200mA, Maximum Voltage 500V 250V AC/DC ��������������������� Max input voltage Diode Test Continuity Check Display Over range indication Polarity Low Battery Indication Input Impedance AC Response ACV Bandwidth Auto Power Off Fuse Batteries Operating Temperature Storage Temperature Operating Altitude Size/Weight Safety 600V AC/DC Test current 1mA max., open circuit voltage of 1.5V typical Audible signal if the resistance is <30Ω, sound off at >150Ω 4000 count 3 -3/4 digit LCD LCD displays “OL” Minus (-) sign for negative polarity “ ” symbol indicates low battery condition >7.5MΩ (VDC & VAC) Average responding 45 to 450Hz 15 minutes (approximately) mA, µA ranges; 0.2A/500V fast acting Resettable Fuse Two 1.5V AAA 41oF to 104oF (5oC to 40oC) 14oF to 140oF (-10oC to 60oC) 7000ft. (2000meters) maximum 4” x 2.165”x 1.28”/0.32 lb. (104x55x32.5mm/145g) UL61010-1 CAT IV-600V Pollution Degree 2, CE Approved

manual for important safety information Indicates hazardous voltages may be present Equipment is protected by double or reinforced insulation Indicates the terminal(s) so marked must not be connected to a circuit where the voltage with respect to earth ground exceeds the maximum safety rating of the meter Indicates the terminal(s) so marked may be subjected to hazardous voltages. MAX 600 V International Safety Symbols Brief Description Typical Applications Category Rating Single phase receptacles and connected loads Three phase circuits and single phase lighting circuits in commercial buildings - Household appliances, power tools - Outlets more than 30ft (10m) from a CAT III source - Outlets more than 60ft (20m) from a CAT IV source - Equipment in fixed installations such as 3-phase motors, switchgear and distribution panels - Lighting circuits in commercial buildings - Feeder lines in industrial plants - Any device or branch circuit that is close to a CAT III source CAT II CAT III The measurement category (CAT) rating and voltage rating is determined by a combination of the meter, test probes and any accessories connected to the meter and test probes. The combination rating is the LOWEST of any individual component. CAT IV Connection point to utility power and outdoor conductors - Primary distribution panels - Overhead or underground lines to detached buildings - Incoming service entrance from utility - Outdoor pumps WARNING: Operation is limited to CAT II applications when the insulated tips are removed from one or both test probes. Refer to Input Limits section of this manual for maximum voltage ratings. CAT III 1000V CAT IV 600V CAT II 1000V Insulated Tip On Insulated Tip Removed 4 Hz% MODE ® Maintenance This Multimeter is designed to provide years of dependable service, if the following care instructions are performed: 1. KEEP THE METER DRY. If it gets wet, wipe it off. 2. USE AND STORE THE METER IN NORMAL TEMPERATURES. Temperature extremes can shorten the life of the electronic parts and distort or melt plastic parts. 3. HANDLE THE METER GENTLY AND CAREFULLY. Dropping it can damage the electronic parts or the case. 4. KEEP THE METER CLEAN. Wipe the case occasionally with a damp cloth. DO NOT use chemicals, cleaning solvents, or detergents. 5. USE ONLY FRESH BATTERIES OF THE RECOMMENDED SIZE AND TYPE. Remove old or weak batteries so they do not leak and damage the unit. 6. IF THE METER IS TO BE STORED FOR A LONG PERIOD OF TIME, the batteries should be removed to prevent damage to the unit. Meter Description 1. Non-contact AC voltage detector probe tip 2. Non-contact AC voltage indicator light 3. LCD display 4. MODE button 5. Rotary function switch 6. Flashlight 7. Flashlight button 8. Hz/% Duty Cycle button 9. Battery Cover 10. Test leads 1. 2. 9. 10. 3. 7. 6. 8. 4. 5.

V Volts A Amps AC Alternating current DC Direct current - Minus sign ����������������������������������������� •))) Continuity Diode test F Farads (capacitance) Hz Hertz (frequency) % Percent (duty ratio) ����������������������� Autoranging Battery status n nano (10-9) µ micro (10-6) m milli (10-3) k kilo (103) M mega (106) �������������������������� ������������������ 6 Operation AC/DC Voltage Measurements 1. Set the rotary function switch to the V Hz% position. 2. Press the button to select AC or DC voltage. 3. Connect the test leads in parallel to the circuit under test. For DC measurements touch the red test probe to the positive side of the circuit and the black test probe to the negative side of the current. 4. Read the voltage on the LCD display AC/DC Current Measurements Observe all safety precautions when working on live voltages. Do not measure current on circuits that exceed 500 V. WARNINGS: Observe all safety precautions when working on live voltages. WARNING: Hz% MODE ® V MODE 1. For current measurements up to 200mA AC/DC, set the rotary function switch to the mA position. 2. For current measurements up to 4000µA AC/DC, set the rotary function switch to the µA position. 3. Press the button to select AC or DC current. 4. Remove power from the circuit under test, then open up the circuit at the point where you wish to measure current. 5. Touch the test probe tips in series with the circuit being measured. For DC current, touch the black test probe to the negative side of the circuit and touch the red test probe to the positive side of the circuit. 6. Apply power to the circuit. 7. Read the current on the LCD display. NOTE: 0.2A/500V fast acting Resettable Fuse on mA and µA ranges. No replacement required. MODE Hz% MODE ®

on a live circuit. WARNING: Hz% MODE ® 1. Set the rotary function switch to the Ω •))) CAP position. 2. Press the button until the “MΩ” symbol appears on the display. 3. Touch the test probe tips across the circuit or part under test. It is best to disconnect one side of the part under test so the rest of the circuit will not interfere with the resistance reading. 4. Read the resistance in on the LCD display. MODE Ω Red Black Black Red Probe Probe Probe Probe Forward test Reverse test 1. Set the rotary function switch to the Ω •))) CAP position. 2. Press the button until the “ ” symbol appears on the display. 3. Touch the test probes to the diode under test. 4. Forward voltage will indicate 0.4V to 0.7V on the LCD display. Reverse voltage will indicate “OL”. Shorted diodes will indicate near 0V and an open diode will indicate “OL” in both polarities. MODE Diode Test Never test diodes in a live circuit. WARNING: Hz% MODE ® 8 Operation cont. Continuity Test Never test continuity on a live circuit. WARNING: 1. Set the rotary function switch to the Ω •))) CAP position. 2. Press the button until the “•)))” symbol appears on the display. 3. Touch the test lead probes to the device or wire being tested. 4. A tone will sound if the resistance is approximately 30 ohms or less. MODE Capacitance Measurements Safely discharge capacitors before taking capacitance measurements. WARNING: 1. Set the rotary function switch to the Ω •))) CAP position. 2. Press the button until the “nF” symbol appears on the display. 3. Connect the test leads to the capacitor to be measured. 4. Read the capacitance on the LCD display. It may take up to a minute to obtain a stable reading on large capacitors. MODE Hz% MODE ® Hz% MODE ® Wire

Observe all safety precautions when working on live voltages. WARNING: 1. Set the rotary function switch to the V HZ % position. 2. Select AC voltage using the button. 3. Press the button once to display Hz (frequency). Pressing the button again will toggle the display to % (duty cycle). 4. Touch the test probe tips to the circuit under test. 5. Read the value on the LCD display. Non-contact AC Voltage Detection (Detection range 100 to 600V) Risk of Electrocution. Before use, always test the Voltage Detector on a known live circuit to verify proper operation. WARNING: 1. Hold the detector probe tip close to an AC voltage. 2. If AC voltage within the specified range is present, the indicator light will illuminate. NOTE: Insulation type and thickness, and distance from the voltage source and other factors may effect operation. Use other methods to verify live voltage if there is any uncertainty. NOTE: The detector is designed with high sensitivity. Static electricity or other sources of energy may randomly trip the sensor. This is normal operation. Hz% MODE ® Hz MODE Hz% 10 REPLACING THE BATTERY To avoid electric shock, disconnect test leads from any source of voltage before removing the battery cover. WARNING: To avoid electric shock, do not operate the meter until the battery cover is in place and fastened securely. WARNING: 1. Remove the one Phillips screw on the bottom of the meter. 2. Remove the battery cover. 3. Replace old batteries with two “AAA” 1.5V batteries. 4. Observe correct polarity. (See label on back of meter.) 5. Close the battery cover and secure the screw. Operation cont. Flashlight 1. Press and hold the button with the symbol to turn on flashlight. 2. Release the button to turn off flashlight. Hz% MODE ® WARNING TO AVOID ELECTRICAL SHOCK, REMOVE TEST LEADS BEFORE OPENING CASE OR BATTERY DOOR. ! 1.5V AAA 1.5V AAA

DC Voltage AC Voltage (50-400Hz) DC Current AC Current 50-60Hz Resistance Capacitance Frequency Duty Cycle 400mV, 4.000V,40.00V, 400.0V, 600V 4.000V, 40.00V 400.0V, 600V 400.0µA, 4000µA 40.00mA, 200.0mA 400.0µA, 4000µA 40.00mA, 200.0mA 400.0Ω 4.000kΩ, 40.00kΩ, 400.0kΩ 4.000MΩ 40.00MΩ 4.000nF 40.00nF 400.0nF 4.000µF, 40.00µF, 100.0µF 9.999Hz, 99.999Hz, 999.9Hz, 9.999kHz, 0.5-99% ± (0.8% rdg + 3d) ± (1.2% rdg + 3d) ± (1.0% rdg + 8d) ± (2.3% rdg + 10d) ± (2.0% rdg + 8d) ± (2.5% rdg + 10d) ± (0.8% rdg + 5d) ± (1.2% rdg + 5d) ± (5.0% rdg + 5d) ± (10.0% rdg + 5d) ± (5.0% rdg + 0.6nF) ± (5.0% rdg + 30d) ± (3.0% rdg + 15d) ± (5.0% rdg + 25d) ± (2.0% rdg + 5d) ± (2.0% rdg + 5d) 12 REGISTER YOUR PRODUCT Register your product purchase at www.southwiretools.com or by scanning the QR code on this manual. At Southwire, we are dedicated to providing you with the best customer experience. By following a few quick steps to register, you can experience quicker service, more efficient support, and receive information on our future products. Simply provide your model number, serial number, and just a few pieces of information about yourself – it is that quick and easy. LIMITED WARRANTY AND LIMITATION OF LIABILITY ON SOUTHWIRE METERS & TESTERS Southwire Company, LLC warrants this product to be free from defects in material and workmanship for two years from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage arising from an accident, neglect, misapplication, contamination, modification, improper maintenance or repair, operation outside of specifications, or abnormal handling of the product. Southwire’s sole liability, and the purchaser’s exclusive remedy, for any breach of this warranty is expressly limited to Southwire’s repair or replacement of the product. Whether Southwire repairs or replaces the product will be a determination that Southwire makes at its sole discretion. SOUTHWIRE MAKES NO WARRANTY THAT THE PRODUCT WILL BE MERCHANTABLE OR FIT FOR ANY PARTICULAR PURPOSE. SOUTHWIRE MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, OTHER THAN THE WARRANTY SPECIFICALLY SET FORTH HEREIN. SOUTHWIRE WILL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES FOR ANY BREACH OF THIS WARRANTY. This warranty is void if this product is used for rental purposes. No product reseller is authorized to extend any other warranty on Southwire’s behalf relating to this product, and no such reseller warranty will be binding on Southwire. If you have a warranty claim, or if the product needs to be serviced during or after the warranty period set forth above, please contact the Customer Service Department at 855-SWTOOLS (855-798-6657). The sender is responsible for all shipping, freight, insurance, and packaging costs associated with sending a product to Southwire. Southwire will not be responsible for lost or damaged products returned pursuant to this warranty. All products returned to Southwire under this warranty should be mailed to: Southwire Company, LLC Attention: Tool Warranty Return 840 Old Bremen Road Carrollton, GA 30117