Sorelle 1050 Manual
Text of Sorelle 1050 Manual
Made in China
Important Information:
Before assembly, read these instructions. Make sure
all preassembled parts are tight. Store this instruction
manual in envelope (attached to mattress support
tube) for future reference.
By Sorelle - A Division of C&T International, Inc.
46 Whelan Road
East Rutherford
N J. 07073 U S A
Tel, +1(201)531 1919 Fax,+1(201)531 1920
Sorelle
1050
CRIB AND MORE
• Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE. DO NOT
USE THIS CRIB IF THE INSTRUCTIONS CANNOT BE STRICTLY FOLLOWED.
• Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use crib is any parts are missing or broken. Ask your dealer or write to C&T
Internatinoal/Sorelle for replacement parts and instructional literature if needed. DO NOT sub
CLEANING & MAINTENANCE
• ALWAYS STORE THE CRIB & CHANGING TABLE IN A CLEAN AND DRY PLACE.
• TO CLEAN YOUR CRIB & CHANGING TABLE, USE A SOFT DAMP CLOTH WITH A SMALL
AMOUNT OF MILD SOAP, WIPE IMMEDIATELY WITH A DRY CLOTH.
• DO NOT USE ABRASIVES OR DETERGENT ON CRIB & CHANGING TABLE SURFACES.
• REGULARLY CHECK ALL SCREWS AND FITTINGS TO ENSURE THEY ARE TIGHT.
• THE IDEAL BALANCE IS TO MAINTAIN THE TEMPERATURE AROUND 21°C (70°F) AND THE
RELA
(A1) Left Side Rail (x1)
(C1) Front Side Rail (x1)
(B1) Back Side Rail (x1)
(D1) (x14)
(E1) Front & Back Contoured Top (x2)
(F1) Rear Leg (x1)
(G1) Front Leg (x1)
(H1) (x2)
(I1) (x2)
Mattress Support Assembly Parts
(Q) Bolt with Loctite®
Threadlocker Blue (x4)
(X1) Dowel Pin (x4)
Allen Wrench
Allen Wrench
ec ra v
r
r
r
r
v
r
r
r
r
r
T
r
v
r
r
r
v
W
r
2
(C-1)Suppo
(C-2)Suppo
(C-3)Suppo
(C-4)La
(C-5)La
(C-6)La
(C-7)D
(L) Rear Dresser Leg (x1)
(M) Front Foot Board Leg (x1)
Screwdriver
(A2) Drawer Bottom (x3)
(B2) Drawer Back (x3)
(C2) Drawer Left (x3)
(D2) Drawer Right (x3)
(E2) Knob (x3)
(F2) Drawer Front (x3)
(G2)
Phillips Screw
Long (x24)
(B2)
(A2)
(C2)
(D2)
(I2)
(H2)
Screw for
Knob (x3)
Screws shown at actual size.
(E2)
Full Size Headboard Parts
(F2)
1. Working on a padded
fl at surface, attach Drawer
Sides (C2 &D2) to Drawer
Back (B2) with Philips Head
Screw. Figure 1.
2. Slide Drawer
Bottom (A2) into drawer
assembly. Figure 2.
3. Secure both sides of
Drawer Front (F2) to drawer
assembly with four (4)
Screws (G2). Figure 3.
Check all screws for
tightness.
4. Using Drawer Knob
Screw (H2), install one (1)
Knob (E2) on Drawer.
Figure 4.